kliver
DD-WRT Novice
Joined: 22 Feb 2015
Posts: 2
|
 Posted: Sun Feb 22, 2015 23:43 Post subject: [Help][TL-WR842NDV2] Usb modem not working |
 |
I'm trying to setup USB modem on TL-WR842NDV2
DD WRT build DD-WRT v24-sp2 (02/02/15) std (SVN revision 26125)
dmesg
| Code: | <5>[ 0.000000] Linux version 3.10.67-rc1 (root@dd-wrt.buildserver) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r43972) ) #8186 Mon Feb 2 04:05:48 CET 2015
<6>[ 0.000000] bootconsole [early0] enabled
<6>[ 0.000000] CPU revision is: 0001974c (MIPS 74Kc)
<4>[ 0.000000] cpu srif ddr srif cpu 535 ddr 400 ahb 200
<6>[ 0.000000] sys id = 10123 Atheros AR9341 rev 1.3 (0x0123)
<6>[ 0.000000] Determined physical RAM map:
<6>[ 0.000000] memory: 02000000 @ 00000000 (usable)
<4>[ 0.000000] Zone ranges:
<4>[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
<4>[ 0.000000] Movable zone start for each node
<4>[ 0.000000] Early memory node ranges
<4>[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
<7>[ 0.000000] On node 0 totalpages: 8192
<7>[ 0.000000] free_area_init_node: node 0, pgdat 802d31b0, node_mem_map 81000000
<7>[ 0.000000] Normal zone: 64 pages used for memmap
<7>[ 0.000000] Normal zone: 0 pages reserved
<7>[ 0.000000] Normal zone: 8192 pages, LIFO batch:0
<4>[ 0.000000] Primary instruction cache 64kB, 4-way, VIPT, I-cache aliases, linesize 32 bytes.
<4>[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
<7>[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
<7>[ 0.000000] pcpu-alloc: [0] 0
<4>[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
<5>[ 0.000000] Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd init=/sbin/init
<6>[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
<6>[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
<6>[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
<6>[ 0.000000] Writing ErrCtl register=00000000
<6>[ 0.000000] Readback ErrCtl register=00000000
<6>[ 0.000000] Memory: 29000k/32768k available (2217k kernel code, 3768k reserved, 381k data, 216k init, 0k highmem)
<6>[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
<6>[ 0.000000] NR_IRQS:83
<6>[ 0.070000] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248)
<6>[ 0.080000] pid_max: default: 32768 minimum: 301
<6>[ 0.080000] Mount-cache hash table entries: 512
<6>[ 0.090000] NET: Registered protocol family 16
<0>[ 0.490000] 25MHZ ref freq
<6>[ 0.510000] bio: create slab at 0
<6>[ 0.520000] Switching to clocksource MIPS
<6>[ 0.530000] NET: Registered protocol family 2
<6>[ 0.530000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
<6>[ 0.530000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
<6>[ 0.540000] TCP: Hash tables configured (established 512 bind 512)
<6>[ 0.540000] TCP: reno registered
<6>[ 0.550000] UDP hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.550000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.560000] NET: Registered protocol family 1
<7>[ 0.560000] PCI: CLS 0 bytes, default 32
<5>[ 0.560000] gpio_proc: module loaded and /proc/gpio/ created
<5>[ 0.570000] wl0gpio_proc: module loaded and /proc/wl0gpio/ created
<6>[ 0.590000] squashfs: version 3.0 (2006/03/15) Phillip Lougher
<6>[ 0.600000] msgmni has been set to 56
<6>[ 0.600000] io scheduler noop registered (default)
<6>[ 0.600000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
<6>[ 0.630000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
<6>[ 0.640000] console [ttyS0] enabled, bootconsole disabled
<0>[ 0.650000] guessed flashsize = 8M
<0>[ 0.660000] scanning for root partition
<0>[ 0.660000] tplink uboot detected
<0>[ 0.660000] guessed bootloader size = 20000
<0>[ 0.670000]
<0>[ 0.670000] found squashfs at 110000
<5>[ 0.680000] Creating 9 MTD partitions on 00
<5>[ 0.680000] 0x000000000000-0x000000020000 :
<5>[ 0.690000] 0x000000020000-0x0000007e0000 :
<5>[ 0.690000] 0x000000110000-0x0000007c0000 :
<5>[ 0.700000] mtd: partition 0x0000rootfs00 :
<5>[ 0.710000] 0x0000007c0000-0x0000007e0000 :
<5>[ 0.710000] 0x0000007e0000-0x0000007f0000 :
<5>[ 0.720000] 0x0000007f0000-0x000000800000 :
<5>[ 0.730000] 0x000000000000-0x000000800000 :
<5>[ 0.730000] 0x000000000000-0x000000020000 :
<5>[ 0.740000] 0x000000010000-0x000000020000 :
<6>[ 0.750000] libphy: Fixed MDIO Bus: probed
<6>[ 0.750000] tun: Universal TUN/TAP device driver, 1.6
<6>[ 0.760000] tun: (C) 1999-2004 Max Krasnyansky
<6>[ 0.770000] PPP generic driver version 2.4.2
<6>[ 0.770000] PPP BSD Compression module registered
<6>[ 0.780000] PPP Deflate Compression module registered
<6>[ 0.780000] PPP MPPE Compression module registered
<6>[ 0.790000] NET: Registered protocol family 24
<6>[ 0.810000] u32 classifier
<6>[ 0.810000] Performance counters on
<6>[ 0.820000] input device check on
<6>[ 0.820000] Actions configured
<6>[ 0.820000] Netfilter messages via NETLINK v0.30.
<6>[ 0.830000] nf_conntrack version 0.5.0 (453 buckets, 1812 max)
<4>[ 0.840000] nf_conntrack_rtsp v0.6.21 loading
<4>[ 0.840000] nf_nat_rtsp v0.6.21 loading
<6>[ 0.840000] ip_tables: (C) 2000-2006 Netfilter Core Team
<6>[ 0.850000] TCP: westwood registered
<6>[ 0.850000] TCP: hybla registered
<6>[ 0.860000] TCP: vegas registered
<6>[ 0.860000] NET: Registered protocol family 17
<5>[ 0.870000] Bridge firewalling registered
<6>[ 0.870000] 8021q: 802.1Q VLAN Support v1.8
<6>[ 0.880000] searching for nvram
<6>[ 0.880000] nvram size = 0
<6>[ 0.910000] Atheros AR71xx hardware watchdog driver version 0.1.0
<6>[ 0.920000] ar71xx-wdt: timeout=15 secs (max=171) ref freq=25000000
<6>[ 0.930000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
<6>[ 0.940000] Freeing unused kernel memory: 216K (802ea000 - 80320000)
<7>[ 3.390000] ar71xx-wdt: enabling watchdog timer
<6>[ 3.450000] libphy: ag71xx_mdio: probed
<6>[ 4.010000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:00 [uid=004dd042, driver=Generic PHY]
<6>[ 4.020000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
<6>[ 4.570000] ag71xx-mdio.1: Found an AR934X built-in switch
<6>[ 4.630000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
<6>[ 4.960000] Loading modules backported from Linux version master-2014-11-04-0-gf3660a2
<6>[ 4.970000] Backport generated by backports.git backports-20141023-2-g4ff890b
<6>[ 5.120000] cfg80211: Calling CRDA to update world regulatory domain
<6>[ 5.150000] cfg80211: World regulatory domain updated:
<6>[ 5.150000] cfg80211: DFS Master region: unset
<6>[ 5.150000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 5.170000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 5.170000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 5.180000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 5.190000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 5.200000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 5.210000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
<7>[ 5.730000] ath: EEPROM regdomain: 0x0
<7>[ 5.730000] ath: EEPROM indicates default country code should be used
<7>[ 5.730000] ath: doing EEPROM country->regdmn map search
<7>[ 5.730000] ath: country maps to regdmn code: 0x3a
<7>[ 5.730000] ath: Country alpha2 being used: US
<7>[ 5.730000] ath: Regpair used: 0x3a
<7>[ 5.740000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
<6>[ 5.740000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=78
<6>[ 5.760000] cfg80211: Calling CRDA for country: US
<6>[ 5.760000] cfg80211: Regulatory domain changed to country: US
<6>[ 5.770000] cfg80211: DFS Master region: FCC
<6>[ 5.770000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 5.780000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
<6>[ 5.790000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
<6>[ 5.800000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (N/A)
<6>[ 5.810000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
<6>[ 5.810000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
<6>[ 6.250000] usbcore: registered new interface driver usbfs
<6>[ 6.260000] usbcore: registered new interface driver hub
<6>[ 6.260000] usbcore: registered new device driver usb
<6>[ 6.330000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
<6>[ 6.370000] ar71xx-ehci ar71xx-ehci.0: Atheros AR91xx built-in EHCI controller
<6>[ 6.380000] ar71xx-ehci ar71xx-ehci.0: new USB bus registered, assigned bus number 1
<4>[ 6.390000] ehci_reset Intialize USB CONTROLLER in host mode: 13
<4>[ 6.400000] ehci_reset Port Status 1c000000
<6>[ 6.400000] eth1: link up (1000Mbps/Full duplex)
<6>[ 6.430000] ar71xx-ehci ar71xx-ehci.0: irq 3, io mem 0x1b000000
<6>[ 6.450000] ar71xx-ehci ar71xx-ehci.0: USB 2.0 started, EHCI 1.00
<6>[ 6.450000] hub 1-0:1.0: USB hub found
<6>[ 6.460000] hub 1-0:1.0: 1 port detected
<6>[ 8.780000] device br0 entered promiscuous mode
<6>[ 8.860000] device eth0 entered promiscuous mode
<6>[ 8.870000] eth1: link down
<6>[ 9.040000] device eth1 entered promiscuous mode
<6>[ 9.050000] br0: port 2(eth1) entered forwarding state
<6>[ 9.060000] br0: port 2(eth1) entered forwarding state
<6>[ 9.060000] device br0 left promiscuous mode
<6>[ 9.070000] device br0 entered promiscuous mode
<6>[ 9.120000] cfg80211: Calling CRDA to update world regulatory domain
<3>[ 9.150000] cfg80211: Invalid regulatory domain detected:
<6>[ 9.150000] cfg80211: Regulatory domain: 00
<6>[ 9.160000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 9.160000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 9.170000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 9.180000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 9.190000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 9.200000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 9.210000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
<6>[ 9.240000] cfg80211: Calling CRDA to update world regulatory domain
<6>[ 9.250000] cfg80211: World regulatory domain updated:
<6>[ 9.250000] cfg80211: DFS Master region: unset
<6>[ 9.260000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 9.270000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 9.270000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 9.280000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 9.290000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 9.300000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 9.310000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
<6>[ 9.340000] cfg80211: Calling CRDA for country: DE
<6>[ 9.370000] cfg80211: Regulatory domain changed to country: DE
<6>[ 9.380000] cfg80211: DFS Master region: ETSI
<6>[ 9.380000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 9.390000] cfg80211: (2400000 KHz - 2483000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 9.400000] cfg80211: (5150000 KHz - 5350000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 9.410000] cfg80211: (5470000 KHz - 5725000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
<6>[ 9.420000] cfg80211: (57240000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
<6>[ 9.770000] br0: port 2(eth1) entered disabled state
<6>[ 10.740000] eth1: link up (1000Mbps/Full duplex)
<6>[ 10.740000] br0: port 2(eth1) entered forwarding state
<6>[ 10.750000] br0: port 2(eth1) entered forwarding state
<6>[ 12.750000] br0: port 2(eth1) entered forwarding state
<6>[ 12.790000] device ath0 entered promiscuous mode
<6>[ 13.230000] br0: port 3(ath0) entered forwarding state
<6>[ 13.240000] br0: port 3(ath0) entered forwarding state
<6>[ 13.320000] device br0 left promiscuous mode
<6>[ 13.550000] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.
<6>[ 15.240000] br0: port 3(ath0) entered forwarding state
<6>[ 18.100000] usbcore: registered new interface driver cdc_acm
<6>[ 18.100000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
<6>[ 18.160000] usbcore: registered new interface driver cdc_wdm
<6>[ 18.260000] usbcore: registered new interface driver qmi_wwan
<6>[ 18.280000] usbcore: registered new interface driver usbserial
<6>[ 18.290000] usbcore: registered new interface driver usbserial_generic
<6>[ 18.290000] usbserial: USB Serial support registered for generic
<6>[ 18.380000] usbcore: registered new interface driver sierra
<6>[ 18.390000] usbserial: USB Serial support registered for Sierra USB modem
<6>[ 18.410000] usbcore: registered new interface driver option
<6>[ 18.420000] usbserial: USB Serial support registered for GSM modem (1-port)
<6>[ 48.620000] usb 1-1: new high-speed USB device number 2 using ar71xx-ehci
<6>[ 48.770000] option 1-1:1.0: GSM modem (1-port) converter detected
<6>[ 48.780000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
<6>[ 48.790000] option 1-1:1.1: GSM modem (1-port) converter detected
<6>[ 48.790000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
<6>[ 48.800000] option 1-1:1.3: GSM modem (1-port) converter detected
<6>[ 48.810000] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2 |
cat /sys/kernel/debug/usb/devices
| Code: | T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.10
S: Manufacturer=Linux 3.10.67-rc1 ehci_hcd
S: Product=Atheros AR91xx built-in EHCI controller
S: SerialNumber=platform
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=19d2 ProdID=0031 Rev= 0.00
S: Manufacturer=ZTE, Incorporated
S: Product=ZTE CDMA Technologies MSM
S: SerialNumber=1234567890ABCDEF
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=84(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms |
Any help?  |
|
