[linearburn]

Is there any plan to support this new N type router I would gladly donate 20$ to see a build for this new linksys product below is a link to the source code for the firmware.


ftp://ftp.linksys.com/opensourcecode/wrt310n/1.00.1/WRT310N_v1.00.1_US.tgz

for any one intrested here is a link for all of linksys open source code

http://www.linksys.com/servlet/Satellite?c=L_CASupport_C1&childpagename=US%2FLayout&cid=1169671246380&pagename=Linksys%2FCommon%2FVisitorWrapper&lid=4638035652B04#WRT310N

it should list all of linksys linux based roughters

I would also be intrested if any one has the tech specs for this router hardwear ect you may be able to find it in the code but im unsure.

Thanks Guys for all the hard work
Sincerly
Nathan/Linear burn

[Sash]

can u give us some hardware info (cpu, ram, flash)?

fcc-id plz, good pics of the pcb!

[Eko]

Linksys WRT310N v1 (4705 cpu, fccid: Linksys Q87-WRT310N

It has new cpu - switch combo, so this is tricky one to figure out, see how much problems we have with wrt300n v1.1

[linearburn]

ill do anything i can except disamble the new roughter if there is any non destructive way i can get info from it ill be glad to help

[cramer]

It'll probablly work as soon as we figure out the exact sequence of Magic(tm) necessary to support the 300Nv11 -- they're exactly the same hardware, as far as I know, in a different case. If you follow the v11 thread, you'll see I have it working under almost unreproducable conditions. I've not been able to get wired and wireless functional at the same time. (probablly an NVRAM issue as the stock firmware chokes as well.)

[SirSilentBob]

As cramer says, same hardware.... I know these pics are shit, but its the best I can do as I don't own this device myself.......

[linearburn]

the pics arnt bad wish they were a higher res but cant gripe I was just wondering this is from a laymans point i know nuthing abought compileing firmwear but cant you pull the drivers for the hardwear from the linux firmear and recompile it in to ddwrt?


Thanks
Nathan

[linearburn]

bump

[Sash]

added here
http://dd-wrt.com/wiki/index.php/Supported_Devices#Linksys

it would help if we had cfe and nvram

read here

http://www.dd-wrt.com/wiki/index.php?title=Broadcom_detection

[Apple][]

Hi

I read the instructions, I think they are telling me that I can either a) load DD WRT on the hardware before I can pull cfe and nvram or b) pull it out via JTAG.

As another option, would it be possible to recompile the linksys firmware, update the ping.asp to accept arbitrary commands and then pull out the data we need?

Just asking for your recommended approach.

[linearburn]

is there any way to get it off the svesoft firmware that is what i currently have on the device however i realy dont care for it. it not nearly as nice as ddwrt

[linearburn]

i can access the comand shell is there a set of commands i can feed it to spit out the needed info you will have to post it exactly as i will have to input it as i am a noob with linux command line

[Sash]

[linearburn]

i couldnt get it to creat that file so im dumping every file on the device that it will alow and plan to up load it in a rar format altho its intersting that the files are rather larger than i expected

[linearburn]

here is the file some of the stuff would not alow me to dump if there is somthing exactly you need on it let me know and ill do my best

part 1 of 4