D-Link Dir-620 (Asus RT-N13U) не коннектится Hu

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Использование и установка DD-WRT
Author Message
Smart-Support
DD-WRT Novice


Joined: 16 Jun 2014
Posts: 2

PostPosted: Mon Jun 16, 2014 10:46    Post subject: D-Link Dir-620 (Asus RT-N13U) не коннектится Hu Reply with quote
Ребята, помогите побороть связку D-Link 620 Rev. A1E (RIR620EEU) в связке с Huawei EC306 (Интертелеком, UA).

Предистория: 620 был перепаян и долго работал как Keenetic на модеме того же Интертелекоме, EC122 вроде как. Работал он не очень стабильно, часто рвал соединение и т.п. Решил поменять оборудование, т.к. поставили рядом вышку с поддержкой Rev. B. Последняя прошивка (не официальная) в которую вшиты драйвера от EC306 модем увидели, но то модем сам по себе исчезал из морды, то тупо отказывался по 20-40 минут подключатся. Решил шиться в DD-WRT, вроде как заявлена поддержка модема и роутер - копия ASUS RT-N13U.

Прошил я последнюю версию от BrainSlayer-V24-preSP2, 05-27-2014-r24160. Но к сожалению счастья не произошло и проставив в настройках WAN порта MobileBroadband и введя все настройки, а так же включив в разделе Service USB support - интернет не поднялся.

Вставив другой модем, тоже EVDO-шный, от МТСа был напуган пришедшими сообщениями в Skype.

Итого все таки какая-то проблема с совместимостью. Но найти причину у меня не получается. Хотелось бы попросить руку помощи у знатоков и гугу сообщества DD-WRT.

Логи:

root@DD-WRT:~# dmesg
Code:

<5>Linux version 3.2.59-svn24090 (root@dd-wrt.buildserver) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.01 r39555) ) #6568 Tue May 27 11:12:05 CEST 2014
<7>prom: fw_arg0=00000001, fw_arg1=81f6efb0, fw_arg2=01f6f3b0, fw_arg3=00000000
<7>argv[0]=  (null) is invalid, skipping
<7>env[0]: memsize=32
<7>env[1]: initrd_start=0x00000000
<7>env[2]: initrd_size=0x0
<7>env[3]: flash_start=0xBF000000
<7>env[4]: flash_size=0x800000
<7>env[0]: memsize=32
<7>env[1]: initrd_start=0x00000000
<7>env[2]: initrd_size=0x0
<7>env[3]: flash_start=0xBF000000
<7>env[4]: flash_size=0x800000
<6>bootconsole [early0] enabled
<6>CPU revision is: 0001964c (MIPS 24KEc)
<6>Ralink RT3052 id:1 rev:3 running at 384.00 MHz
<6>Determined physical RAM map:
<6> memory: 02000000 @ 00000000 (usable)
<4>Zone PFN ranges:
<4>  Normal   0x00000000 -> 0x00002000
<4>Movable zone start PFN for each node
<4>early_node_map[1] active PFN ranges
<4>    0: 0x00000000 -> 0x00002000
<7>On node 0 totalpages: 8192
<7>free_area_init_node: node 0, pgdat 80260700, node_mem_map 81000000
<7>  Normal zone: 64 pages used for memmap
<7>  Normal zone: 0 pages reserved
<7>  Normal zone: 8128 pages, LIFO batch:0
<7>pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
<7>pcpu-alloc: [0] 0
<4>Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
<5>Kernel command line:  console=ttyS1,57600n8 root=/dev/mtdblock4 rootfstype=squashfs noinitrd
<6>PID hash table entries: 128 (order: -3, 512 bytes)
<6>Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
<6>Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
<4>Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
<4>Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
<6>Writing ErrCtl register=0003ba28
<6>Readback ErrCtl register=0003ba28
<6>Memory: 29556k/32768k available (2166k kernel code, 3212k reserved, 326k data, 160k init, 0k highmem)
<6>NR_IRQS:48
<6>console [ttyS1] enabled, bootconsole disabled
<6>Calibrating delay loop... 255.59 BogoMIPS (lpj=1277952)
<6>pid_max: default: 4096 minimum: 301
<6>Mount-cache hash table entries: 512
<6>NET: Registered protocol family 16
<6>bio: create slab <bio-0> at 0
<5>SCSI subsystem initialized
<6>Switching to clocksource MIPS
<6>NET: Registered protocol family 2
<6>IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
<6>TCP established hash table entries: 1024 (order: 1, 8192 bytes)
<6>TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
<6>TCP: Hash tables configured (established 1024 bind 1024)
<6>TCP reno registered
<6>NET: Registered protocol family 1
<6>squashfs: version 3.0 (2006/03/15) Phillip Lougher
<6>msgmni has been set to 57
<6>io scheduler noop registered
<6>io scheduler deadline registered (default)
<6>Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
<6>serial8250: ttyS0 at MMIO 0x10000500 (irq = 13) is a 16550A
<6>serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
<4>Ralink gpio driver initialized
<6>system type: RT3052
<6>boot type: 0
<5>ralink flash device: 0x1000000 at 0xbf000000
<6>Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
<7>Ralink SoC physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
<6>Amd/Fujitsu Extended Query Table at 0x0040
<6>  Amd/Fujitsu Extended Query version 1.1.
<5>number of CFI chips: 1
<0>
<0>found squashfs at 12E000
<5>Creating 6 MTD partitions on "Ralink SoC physically mapped flash":
<5>0x000000000000-0x000000030000 : "uboot"
<5>0x000000030000-0x000000040000 : "uboot-config"
<5>0x000000040000-0x000000050000 : "factory-defaults"
<5>0x000000050000-0x0000007f0000 : "linux"
<5>0x00000012e000-0x0000007f0000 : "rootfs"
<4>mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
<5>0x0000007f0000-0x000000800000 : "nvram"
<6>tun: Universal TUN/TAP device driver, 1.6
<6>tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
<6>PPP generic driver version 2.4.2
<6>PPP BSD Compression module registered
<6>PPP Deflate Compression module registered
<6>PPP MPPE Compression module registered
<6>NET: Registered protocol family 24
<6>Ralink APSoC Hardware Watchdog Timer
<6>u32 classifier
<6>    Performance counters on
<6>    Actions configured
<6>Netfilter messages via NETLINK v0.30.
<6>nf_conntrack version 0.5.0 (461 buckets, 1844 max)
<6>ctnetlink v0.93: registering with nfnetlink.
<6>IPv4 over IPv4 tunneling driver
<6>ip_tables: (C) 2000-2006 Netfilter Core Team
<6>IPP2P v0.8.2 loading
<6>ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
<6>TCP bic registered
<6>TCP cubic registered
<6>TCP westwood registered
<6>TCP highspeed registered
<6>TCP hybla registered
<6>TCP htcp registered
<6>TCP vegas registered
<6>TCP scalable registered
<6>NET: Registered protocol family 17
<5>Bridge firewalling registered
<6>8021q: 802.1Q VLAN Support v1.8
<6>searching for nvram
<6>nvram size = 0
<4>MAC_ADRH -- : 0x0000000c
<4>MAC_ADRL -- : 0x43305277
<4>MAC_ADRH -- : 0x0000000c
<4>MAC_ADRL -- : 0x43305277
<4>Ralink APSoC Ethernet Driver Initilization. v2.0  256 rx/tx descriptors allocated, mtu = 1500!
<4>NAPI enable, Tx Ring = 256, Rx Ring = 256
<4>MAC_ADRH -- : 0x0000000c
<4>MAC_ADRL -- : 0x43305277
<4>rt3052 access driver initialization.
<6>VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
<6>Freeing unused kernel memory: 160k freed
<4>rt2860v2_ap: module license 'unspecified' taints kernel.
<4>Disabling lock debugging due to kernel taint
<4>
<4>phy_tx_ring = 0x01579000, tx_ring = 0xa1579000
<4>
<4>phy_rx_ring0 = 0x0157a000, rx_ring0 = 0xa157a000
<4>RT305x_ESW: Link Status Changed
<4>CDMA_CSG_CFG = 81000007
<4>GDMA1_FWD_CFG = 710000
<6>Started WatchDog Timer.
<6>usbcore: registered new interface driver usbfs
<6>usbcore: registered new interface driver hub
<6>usbcore: registered new device driver usb
<6>dwc_otg: version 2.72a 24-JUN-2008
<6>DWC_otg: Core Release: 2.66a
<6>DWC_otg: Periodic Transfer Interrupt Enhancement - disabled
<6>DWC_otg: Multiprocessor Interrupt Enhancement - disabled
<6>DWC_otg: Using DMA mode
<6>DWC_otg: Device using Buffer DMA mode
<6>dwc_otg lm0: DWC OTG Controller
<6>dwc_otg lm0: new USB bus registered, assigned bus number 1
<6>dwc_otg lm0: irq 26, io mem 0x00000000
<6>DWC_otg: Init: Port Power? op_state=1
<6>DWC_otg: Init: Power Port (0)
<6>hub 1-0:1.0: USB hub found
<6>hub 1-0:1.0: 1 port detected
<6>usbcore: registered new interface driver libusual
<6>usb 1-1: new high-speed USB device number 2 using dwc_otg
<3>hub 1-0:1.0: port 1 disabled by hub (EMI?), re-enabling...
<6>usb 1-1: USB disconnect, device number 2
<6>device br0 entered promiscuous mode
<6>device vlan1 entered promiscuous mode
<6>device eth2 entered promiscuous mode
<6>device vlan2 entered promiscuous mode
<6>br0: port 2(vlan2) entering forwarding state
<6>br0: port 2(vlan2) entering forwarding state
<6>br0: port 1(vlan1) entering forwarding state
<6>br0: port 1(vlan1) entering forwarding state
<6>device br0 left promiscuous mode
<6>device br0 entered promiscuous mode
<4>RtmpOSNetDevDetach(): RtmpOSNetDeviceDetach(), dev->name=ra0!
<4>0x1300 = 00064380
<4>0x1300 = 00064380
<6>device ra0 entered promiscuous mode
<6>br0: port 3(ra0) entering forwarding state
<6>br0: port 3(ra0) entering forwarding state
<6>device br0 left promiscuous mode
<6>br0: port 2(vlan2) entering forwarding state
<6>br0: port 1(vlan1) entering forwarding state
<6>usb 1-1: new high-speed USB device number 3 using dwc_otg
<6>br0: port 3(ra0) entering forwarding state
<6>usbcore: registered new interface driver usbserial
<6>USB Serial support registered for generic
<6>usbcore: registered new interface driver usbserial_generic
<6>usbserial: USB Serial Driver core
<6>USB Serial support registered for GSM modem (1-port)
<6>usbcore: registered new interface driver option
<6>option: v0.7.2:USB Driver for GSM modems
<3>hub 1-0:1.0: port 1 disabled by hub (EMI?), re-enabling...
<6>usb 1-1: USB disconnect, device number 3
<6>usb 1-1: new high-speed USB device number 4 using dwc_otg
<6>option 1-1:1.0: GSM modem (1-port) converter detected
<6>usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
<6>option 1-1:1.1: GSM modem (1-port) converter detected
<6>usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
<6>option 1-1:1.2: GSM modem (1-port) converter detected
<6>usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2
<3>hub 1-0:1.0: port 1 disabled by hub (EMI?), re-enabling...
<6>usb 1-1: USB disconnect, device number 4
<3>option: option_instat_callback: error -2
<6>option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
<6>option 1-1:1.0: device disconnected
<6>option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
<6>option 1-1:1.1: device disconnected
<6>option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2
<6>option 1-1:1.2: device disconnected




root@DD-WRT:~# cat /proc/bus/usb/devices

Code:
T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480  MxCh= 1
B:  Alloc=  0/800 us ( 0%), #Int=  1, #Iso=  0
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1d6b ProdID=0002 Rev= 3.02
S:  Manufacturer=Linux 3.2.59-svn24090 dwc_otg_hcd
S:  Product=DWC OTG Controller
S:  SerialNumber=lm0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   4 Ivl=256ms

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 11 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=12d1 ProdID=1506 Rev= 0.00
S:  Manufacturer=Huawei Technologies
S:  Product=HUAWEI Mobile
C:* #Ifs= 3 Cfg#= 1 Atr=c0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=option
E:  Ad=81(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=02 Driver=option
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=03 Driver=option
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
[/size]


Подскажите пожалуйста куда рыть и в чем может быть проблема. Огромное спасибо.
Sponsor
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Использование и установка DD-WRT All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum