DD-WRT :: View topic - TP-Link TL-WR841ND v8 переназначить WAN

TP-Link TL-WR841ND v8 переназначить WAN

DD-WRT Forum Index -> Оборудование на основе Atheros WiSOC

Goto page 1, 2, 3, 4, 5 Next

View previous topic :: View next topic

Author

Message

mfch
DD-WRT Novice

Joined: 04 Jun 2014
Posts: 15

Posted: Wed Jun 04, 2014 20:58 Post subject: TP-Link TL-WR841ND v8 переназначить WAN

Здравствуйте.
TP-Link TL-WR841ND v8
Atheros AR9341 rev 1.1 (0x0121)
DD-WRT v24-sp2 (05/27/14) - build 24160
WAN IP: 0.0.0.0

После грозы перестал появляться интернет, хотя индикатор горит постоянно, что с кабелем провайдера, что без него.
Есть ли возможность на данной модели переназначить WAN-порт? Если да, как именно это сделать?
Заранее благодарен!

Sponsor

vasek00
DD-WRT Guru

Joined: 06 Nov 2010
Posts: 3312

Posted: Thu Jun 05, 2014 5:31 Post subject: Re: TP-Link TL-WR841ND v8 переназначить WAN

mfch wrote:

Данный чип имеет встроенный switch.
1.Вывод команды dmesg
2.Вывод команды ifconfig

Можно предположить что у вас все сидит на eth0

3.Вывод команды swconfig dev eth0 show

4.Если пройдет то интересует самый низ

Code:

VLAN 1:
vid: 1
ports: 0t 1 3 4 5
VLAN 2:
vid: 2
ports: 0t 2

mfch
DD-WRT Novice

Joined: 04 Jun 2014
Posts: 15

Posted: Thu Jun 05, 2014 8:04 Post subject: Re: TP-Link TL-WR841ND v8 переназначить WAN

vasek00, спасибо за оперативный ответ.
1.Вывод команды dmesg

Code:

<6>[ 0.000000] bootconsole [early0] enabled
<6>[ 0.000000] CPU revision is: 0001974c (MIPS 74Kc)
<4>[ 0.000000] cpu srif ddr srif cpu 535 ddr 400 ahb 200
<6>[ 0.000000] sys id = 121 Atheros AR9341 rev 1.1 (0x0121)
<6>[ 0.000000] Determined physical RAM map:
<6>[ 0.000000] memory: 02000000 @ 00000000 (usable)
<4>[ 0.000000] Zone ranges:
<4>[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
<4>[ 0.000000] Movable zone start for each node
<4>[ 0.000000] Early memory node ranges
<4>[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
<7>[ 0.000000] On node 0 totalpages: 8192
<7>[ 0.000000] free_area_init_node: node 0, pgdat 802aabc0, node_mem_map 81000000
<7>[ 0.000000] Normal zone: 64 pages used for memmap
<7>[ 0.000000] Normal zone: 0 pages reserved
<7>[ 0.000000] Normal zone: 8192 pages, LIFO batch:0
<4>[ 0.000000] Primary instruction cache 64kB, 4-way, VIPT, I-cache aliases, linesize 32 bytes.
<4>[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
<7>[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
<7>[ 0.000000] pcpu-alloc: [0] 0
<4>[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
<5>[ 0.000000] Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd init=/sbin/init
<6>[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
<6>[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
<6>[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
<6>[ 0.000000] Writing ErrCtl register=00000000
<6>[ 0.000000] Readback ErrCtl register=00000000
<6>[ 0.000000] Memory: 29196k/32768k available (2093k kernel code, 3572k reserved, 341k data, 188k init, 0k highmem)
<6>[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
<6>[ 0.000000] NR_IRQS:83
<6>[ 0.070000] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248)
<6>[ 0.080000] pid_max: default: 32768 minimum: 301
<6>[ 0.080000] Mount-cache hash table entries: 512
<6>[ 0.090000] NET: Registered protocol family 16
<0>[ 0.490000] 25MHZ ref freq
<6>[ 0.510000] bio: create slab at 0
<6>[ 0.520000] Switching to clocksource MIPS
<6>[ 0.530000] NET: Registered protocol family 2
<6>[ 0.530000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
<6>[ 0.530000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
<6>[ 0.540000] TCP: Hash tables configured (established 512 bind 512)
<6>[ 0.540000] TCP: reno registered
<6>[ 0.540000] UDP hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.550000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.560000] NET: Registered protocol family 1
<7>[ 0.560000] PCI: CLS 0 bytes, default 32
<5>[ 0.560000] gpio_proc: module loaded and /proc/gpio/ created
<5>[ 0.570000] wl0gpio_proc: module loaded and /proc/wl0gpio/ created
<6>[ 0.590000] squashfs: version 3.0 (2006/03/15) Phillip Lougher
<6>[ 0.590000] msgmni has been set to 57
<6>[ 0.600000] io scheduler noop registered (default)
<6>[ 0.600000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
<6>[ 0.630000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
<6>[ 0.640000] console [ttyS0] enabled, bootconsole disabled
<0>[ 0.650000] guessed flashsize = 4M
<0>[ 0.650000] scanning for root partition
<0>[ 0.660000] tplink uboot detected
<0>[ 0.660000] guessed bootloader size = 20000
<0>[ 0.670000]
<0>[ 0.670000] found squashfs at 110000
<5>[ 0.680000] Creating 8 MTD partitions on 00
<5>[ 0.680000] 0x000000000000-0x000000020000 :
<5>[ 0.690000] 0x000000020000-0x0000003e0000 :
<5>[ 0.690000] 0x000000110000-0x0000003d0000 :
<5>[ 0.700000] mtd: partition 0x0000rootfs00 :
<5>[ 0.710000] 0x0000003d0000-0x0000003e0000 :
<5>[ 0.710000] 0x0000003e0000-0x0000003f0000 :
<5>[ 0.720000] 0x0000003f0000-0x000000400000 :
<5>[ 0.730000] 0x000000000000-0x000000400000 :
<5>[ 0.730000] 0x000000000000-0x000000020000 :
<6>[ 0.740000] libphy: Fixed MDIO Bus: probed
<6>[ 0.750000] tun: Universal TUN/TAP device driver, 1.6
<6>[ 0.750000] tun: (C) 1999-2004 Max Krasnyansky
<6>[ 0.760000] PPP generic driver version 2.4.2
<6>[ 0.760000] PPP BSD Compression module registered
<6>[ 0.770000] PPP Deflate Compression module registered
<6>[ 0.770000] PPP MPPE Compression module registered
<6>[ 0.780000] NET: Registered protocol family 24
<6>[ 0.800000] u32 classifier
<6>[ 0.800000] Performance counters on
<6>[ 0.810000] input device check on
<6>[ 0.810000] Actions configured
<6>[ 0.820000] Netfilter messages via NETLINK v0.30.
<6>[ 0.820000] nf_conntrack version 0.5.0 (456 buckets, 1824 max)
<4>[ 0.830000] nf_conntrack_rtsp v0.6.21 loading
<4>[ 0.830000] nf_nat_rtsp v0.6.21 loading
<6>[ 0.840000] ip_tables: (C) 2000-2006 Netfilter Core Team
<6>[ 0.840000] TCP: westwood registered
<6>[ 0.850000] TCP: hybla registered
<6>[ 0.850000] TCP: vegas registered
<6>[ 0.850000] NET: Registered protocol family 17
<5>[ 0.860000] Bridge firewalling registered
<6>[ 0.860000] 8021q: 802.1Q VLAN Support v1.8
<6>[ 0.870000] searching for nvram
<6>[ 0.870000] nvram size = 0
<6>[ 0.900000] Atheros AR71xx hardware watchdog driver version 0.1.0
<6>[ 0.910000] ar71xx-wdt: timeout=15 secs (max=171) ref freq=25000000
<6>[ 0.920000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
<6>[ 0.930000] Freeing unused kernel memory: 188K (802c1000 - 802f0000)
<7>[ 2.850000] ar71xx-wdt: enabling watchdog timer
<6>[ 2.940000] libphy: ag71xx_mdio: probed
<6>[ 3.490000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:00 [uid=004dd042, driver=Generic PHY]
<6>[ 3.500000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
<6>[ 4.060000] ag71xx-mdio.1: Found an AR934X built-in switch
<6>[ 5.100000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
<6>[ 7.390000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
<6>[ 7.400000] Backport generated by backports.git backports-20140320-37-g5c33da0
<6>[ 7.550000] cfg80211: Calling CRDA to update world regulatory domain
<6>[ 7.580000] cfg80211: World regulatory domain updated:
<6>[ 7.580000] cfg80211: DFS Master region: unset
<6>[ 7.580000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 7.590000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 7.600000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 7.610000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 7.620000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 7.630000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 7.640000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
<6>[ 7.820000] eth1: link up (1000Mbps/Full duplex)
<7>[ 8.140000] ath: EEPROM regdomain: 0x0
<7>[ 8.140000] ath: EEPROM indicates default country code should be used
<7>[ 8.140000] ath: doing EEPROM country->regdmn map search
<7>[ 8.140000] ath: country maps to regdmn code: 0x3a
<7>[ 8.140000] ath: Country alpha2 being used: US
<7>[ 8.140000] ath: Regpair used: 0x3a
<7>[ 8.150000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
<6>[ 8.150000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=78
<6>[ 8.170000] cfg80211: Calling CRDA for country: US
<6>[ 8.230000] cfg80211: Regulatory domain changed to country: US
<6>[ 8.230000] cfg80211: DFS Master region: FCC
<6>[ 8.240000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 8.250000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
<6>[ 8.260000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
<6>[ 8.270000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (N/A)
<6>[ 8.270000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
<6>[ 8.280000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
<6>[ 8.490000] eth0: link up (100Mbps/Half duplex)
<6>[ 11.140000] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.
<6>[ 11.660000] device br0 entered promiscuous mode
<6>[ 11.690000] eth1: link down
<6>[ 12.550000] eth0: link down
<6>[ 13.790000] device eth1 entered promiscuous mode
<6>[ 13.800000] device br0 left promiscuous mode
<6>[ 13.810000] device br0 entered promiscuous mode
<6>[ 13.860000] cfg80211: Calling CRDA to update world regulatory domain
<3>[ 13.890000] cfg80211: Invalid regulatory domain detected:
<6>[ 13.890000] cfg80211: Regulatory domain: 00
<6>[ 13.900000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 13.900000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 13.910000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 13.920000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 13.930000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 13.940000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 13.950000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
<6>[ 13.980000] cfg80211: Calling CRDA to update world regulatory domain
<6>[ 14.000000] cfg80211: World regulatory domain updated:
<6>[ 14.010000] cfg80211: DFS Master region: unset
<6>[ 14.010000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 14.020000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 14.030000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 14.040000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 14.050000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 14.060000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 14.060000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
<6>[ 14.090000] cfg80211: Calling CRDA for country: US
<6>[ 14.120000] cfg80211: Regulatory domain changed to country: US
<6>[ 14.130000] cfg80211: DFS Master region: FCC
<6>[ 14.130000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 14.140000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
<6>[ 14.150000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
<6>[ 14.160000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (N/A)
<6>[ 14.160000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
<6>[ 14.170000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
<6>[ 14.500000] eth1: link up (1000Mbps/Full duplex)
<6>[ 14.500000] br0: port 1(eth1) entered forwarding state
<6>[ 14.510000] br0: port 1(eth1) entered forwarding state
<6>[ 15.550000] eth0: link up (100Mbps/Half duplex)
<6>[ 16.510000] br0: port 1(eth1) entered forwarding state
<6>[ 17.330000] device ath0 entered promiscuous mode
<6>[ 17.330000] br0: port 2(ath0) entered forwarding state
<6>[ 17.340000] br0: port 2(ath0) entered forwarding state
<6>[ 17.400000] device br0 left promiscuous mode
<6>[ 18.200000] device eth0 entered promiscuous mode
<6>[ 18.240000] eth0: link down
<6>[ 18.350000] device eth0 left promiscuous mode
<6>[ 18.550000] eth0: link up (100Mbps/Half duplex)
<6>[ 19.340000] br0: port 2(ath0) entered forwarding state
<6>[ 47.550000] device eth1 left promiscuous mode
<6>[ 47.560000] br0: port 1(eth1) entered disabled state
<6>[ 47.570000] device ath0 left promiscuous mode
<6>[ 47.580000] br0: port 2(ath0) entered disabled state
<6>[ 48.100000] eth0: link down
<6>[ 50.430000] device br0 entered promiscuous mode
<6>[ 50.490000] eth1: link down
<6>[ 52.590000] device eth1 entered promiscuous mode
<6>[ 52.600000] device br0 left promiscuous mode
<6>[ 52.610000] device br0 entered promiscuous mode
<6>[ 53.190000] eth1: link up (1000Mbps/Full duplex)
<6>[ 53.190000] br0: port 1(eth1) entered forwarding state
<6>[ 53.200000] br0: port 1(eth1) entered forwarding state
<6>[ 54.900000] cfg80211: Calling CRDA to update world regulatory domain
<3>[ 54.900000] cfg80211: Invalid regulatory domain detected:
<6>[ 54.910000] cfg80211: Regulatory domain: 00
<6>[ 54.910000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 54.930000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 54.930000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 54.940000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 54.950000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 54.960000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 54.970000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
<6>[ 54.990000] cfg80211: Calling CRDA to update world regulatory domain
<6>[ 55.020000] cfg80211: World regulatory domain updated:
<6>[ 55.020000] cfg80211: DFS Master region: unset
<6>[ 55.030000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 55.040000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 55.050000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 55.060000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 55.060000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 55.070000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 55.080000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
<6>[ 55.120000] cfg80211: Calling CRDA for country: US
<6>[ 55.140000] cfg80211: Regulatory domain changed to country: US
<6>[ 55.150000] cfg80211: DFS Master region: FCC
<6>[ 55.150000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 55.160000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
<6>[ 55.170000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
<6>[ 55.180000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (N/A)
<6>[ 55.180000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
<6>[ 55.190000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
<6>[ 55.200000] br0: port 1(eth1) entered forwarding state
<6>[ 58.170000] device ath0 entered promiscuous mode
<6>[ 58.180000] br0: port 2(ath0) entered forwarding state
<6>[ 58.180000] br0: port 2(ath0) entered forwarding state
<6>[ 58.240000] device br0 left promiscuous mode
<6>[ 58.710000] device eth0 entered promiscuous mode
<6>[ 58.760000] device eth0 left promiscuous mode
<6>[ 58.990000] eth0: link up (100Mbps/Half duplex)
<6>[ 60.180000] br0: port 2(ath0) entered forwarding state

2.Вывод команды ifconfig

Code:

ath0 Link encap:Ethernet HWaddr A0:F3:C1:EF:8B:AA
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:340 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:60373 (58.9 KiB)
br0 Link encap:Ethernet HWaddr A0:F3:C1:EF:8B:AA
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:3670 errors:0 dropped:254 overruns:0 frame:0
TX packets:3359 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:319806 (312.3 KiB) TX bytes:3490858 (3.3 MiB)
br0:0 Link encap:Ethernet HWaddr A0:F3:C1:EF:8B:AA
inet addr:169.254.255.1 Bcast:169.254.255.255 Mask:255.255.0.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
eth0 Link encap:Ethernet HWaddr A0:F3:C1:EF:8B:AA
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:7 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:2394 (2.3 KiB)
Interrupt:4
eth1 Link encap:Ethernet HWaddr A0:F3:C1:EF:8B:AA
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:3757 errors:0 dropped:30 overruns:0 frame:0
TX packets:3359 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:383341 (374.3 KiB) TX bytes:3490858 (3.3 MiB)
Interrupt:5
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MULTICAST MTU:65536 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

3.Вывод команды swconfig dev eth0 show

Code:

Global attributes:
enable_vlan: 0
Port 0:
pvid: 1
link: port:0 link:up speed:1000baseT full-duplex txflow rxflow
Port 1:
pvid: 1
link: port:1 link:down
Port 2:
pvid: 1
link: port:2 link:up speed:100baseT full-duplex auto
Port 3:
pvid: 1
link: port:3 link:down
Port 4:
pvid: 1
link: port:4 link:down
VLAN 1:
vid: 1
ports: 0 1 2 3 4

vasek00
DD-WRT Guru

Joined: 06 Nov 2010
Posts: 3312

Posted: Thu Jun 05, 2014 9:25 Post subject: Re: TP-Link TL-WR841ND v8 переназначить WAN

Попытаюсь объяснить ваш случай.
Структура данного switch имеет приближенный вид таковой:
Port 0 ------ GMII 1000M
Port 1 +
Port 2 +
Port 3 +
Port 4 +

Port W ------ MII 100/10M

Тут можно поступить так, используя команду swconfig сконфигурировать новые два сетевых интерфейса на рабочем канале GMII 1000М на котором висят LAN порты.

Code:

swconfig dev eth0 set reset
swconfig dev eth0 set enable_vlan 1
swconfig dev eth0 vlan 1 set ports "0t 1 2 3"
swconfig dev eth0 vlan 2 set ports "0t 4"
swconfig dev eth0 set apply

Для WEB настроек было eth1 - WAN порт, стало vlan2.
Помним что в br0 - находятся LAN порты и wi-fi ath0 в месте, а у нас было br0 = eth0+ath0. Значит мост нужно разобрать и опять собрать.

Code:

brctl delif br0 eth0
brctl addif br0 vlan1
brctl show

т.е. в место eth0 ставим новый vlan1

И так для первого варианта текст выглядит так

Code:

#!/bin/sh
swconfig dev eth0 set reset
swconfig dev eth0 set enable_vlan 1
swconfig dev eth0 vlan 1 set ports "0t 1 2 3"
swconfig dev eth0 vlan 2 set ports "0t 4"
swconfig dev eth0 set apply
brctl delif br0 eth0
brctl addif br0 vlan1
brctl show

Его поместить в скрипт http://192.168.1.1/Diagnostics.asp Command Shell - Commands
Нажать на кнопку Save Custom Script в каталоге /tmp появиться файл custom.sh готовый для запуска или просто выполнить.
Если потеряете связь по LAN то Wi-fi должен работать, или просто перезагрузите роутер, но тогда не узнаем где была ошибка.

Далее физически определиться с расположением 4 порта с реальным который может иметь обозначение на роутере 4 или 1. И WEB сделать последний штрих на странице http://192.168.1.1/Networking.asp в разделе Port Setup -
WAN Port Assignment назначить данному порту значение vlan2 в место eth1

mfch
DD-WRT Novice

Joined: 04 Jun 2014
Posts: 15

Posted: Thu Jun 05, 2014 13:05 Post subject: Re: TP-Link TL-WR841ND v8 переназначить WAN

vasek00 wrote:

И так для первого варианта текст выглядит так

Code:

Спасибо за подробный ответ.
С созданием и выполнением скрипта все более или менее понятно. Есть ли какой-то критерий правильного его выполнения?

Пожалуйста, напишите, как физически определить расположение 4 порта. Это и будет новый WAN?

vasek00
DD-WRT Guru

Joined: 06 Nov 2010
Posts: 3312

Posted: Thu Jun 05, 2014 16:14 Post subject: Re: TP-Link TL-WR841ND v8 переназначить WAN

Критерий выполнения это хвост от выполненой команды swconfig ... show , в ней должно появиться два VLAN 1 и 2. Пример был мной выложен выше.
Все зависит от схемотехники, данный порт 4 он должен пропасть из локальной сети после выполнения команд swconfig, т.е. если ПК дать стат.Ip и обратиться к 192.168.1.1 то на одном из портов ping не будет (если мы взяли 1 или 4 то это крайние порты), мало вероятно что он будет в середине, а на остальных трех должны быть. При проверки кабель лучше отключить от роутера или оставить в WAN порту, но не в LAN портах. Как все получиться включаете кабель от провайдера в найденный порт.

Или найти в интернете более точную схему расположения портов для данного чипа, я для AR9341 не нашел есть физический номер порта и логический номер порта, так вот на роутере написаны физ.порты, а мы с вами работаем с логическими.

mfch
DD-WRT Novice

Joined: 04 Jun 2014
Posts: 15

Posted: Thu Jun 05, 2014 18:30 Post subject: Re: TP-Link TL-WR841ND v8 переназначить WAN

Еще раз прошу прощения. Видать я совсем-совсем не в теме. Прошу подкорректировать пошаговую инструкцию.
1. swconfig dev eth0 show
На выходе должны появиться VLAN 1 и 2. У себя я этого не наблюдаю.

Quote:

VLAN 1:
vid: 1
ports: 0 1 2 3 4

2. Мои дальнейшие действия?

Quote:

Критерий выполнения это хвост от выполненой команды swconfig ... show , в ней должно появиться два VLAN 1 и 2. Пример был мной выложен выше.

Все зависит от схемотехники, данный порт 4 он должен пропасть из локальной сети после выполнения команд swconfig, т.е. если ПК дать стат.Ip и обратиться к 192.168.1.1 то на одном из портов ping не будет (если мы взяли 1 или 4 то это крайние порты), мало вероятно что он будет в середине, а на остальных трех должны быть. При проверки кабель лучше отключить от роутера или оставить в WAN порту, но не в LAN портах. Как все получиться включаете кабель от провайдера в найденный порт.

Или найти в интернете более точную схему расположения портов для данного чипа, я для AR9341 не нашел есть физический номер порта и логический номер порта, так вот на роутере написаны физ.порты, а мы с вами работаем с логическими.

Quote:

vasek00
DD-WRT Guru

Joined: 06 Nov 2010
Posts: 3312

Posted: Fri Jun 06, 2014 5:16 Post subject: Re: TP-Link TL-WR841ND v8 переназначить WAN

mfch wrote:

3.Вывод команды swconfig dev eth0 show

Code:

По этому лучше все делать по шагам.
Пк либо wi-fi либо 2 или 3 порт LAN, на нем стат.IP. Подключиться к роутеру, через telnet набрать команды, так как из вашего поста видно, что она на eth0 прошла:

Code:

swconfig dev eth0 set enable_vlan 1
swconfig dev eth0 vlan 1 set ports "0t 1 2 3"
swconfig dev eth0 vlan 2 set ports "0t 4"
swconfig dev eth0 set apply

Проверить результат должно быть:
swconfig dev eth0 show

Code:

Global attributes:
enable_vlan: 1
...
Port 0:
...
pvid: 0
link: port:0 link:up speed:1000baseT full-duplex txflow rxflow
Port 1:
...
pvid: 1
link: port:1 link:up speed:100baseT full-duplex auto
Port 2:
...
pvid: 2
link: port:2 link:down
Port 3:
...
pvid: 1
link: port:3 link:down
Port 4:
...
pvid: 1
link: port:4 link:up speed:100baseT full-duplex auto
Port 5:
...
pvid: 1
link: port:5 link:down
VLAN 1:
vid: 1
ports: 0t 1 3 4 5
VLAN 2:
vid: 2
ports: 0t 2

В данном случае port 2 по физике это WAN.

Вот другой пример с добавленным еще vlan :

Code:

swconfig dev eth0 vlan 1 set ports "0t 3 4 5"
swconfig dev eth0 vlan 3 set ports "0t 1"
swconfig dev switch0 set apply
swconfig dev eth0 show
Global attributes:
enable_vlan: 1
...
Port 0:
...
pvid: 0
link: port:0 link:up speed:1000baseT full-duplex txflow rxflow
Port 1:
...
pvid: 3
link: port:1 link:up speed:100baseT full-duplex auto
Port 2:
...
pvid: 2
link: port:2 link:down
Port 3:
...
pvid: 1
link: port:3 link:down
Port 4:
...
pvid: 1
link: port:4 link:up speed:100baseT full-duplex auto
Port 5:
...
pvid: 1
link: port:5 link:down
VLAN 1:
vid: 1
ports: 0t 3 4 5
VLAN 2:
vid: 2
ports: 0t 2
VLAN 3:
vid: 3
ports: 0t 1

Получили на Port 1 - pvid 3 или VLAN 3 ports - "0t 1"
Если пойти еще дальше, то например можно подгять pppoe на vlan3 в ручную:

Code:

vconfig add eth0 3
ifconfig vlan3 up
echo -e "plugin /usr/lib/rp-pppoe.so

nic-vlan3
noccp
nomppc
noipdefault
noauth
defaultroute
noaccomp
nobsdcomp
nodeflate
nopcomp
nomppe
usepeerdns
user 'USER'
password 'PASSWD'
default-asyncmap
mtu 1492
mru 1492
persist
lcp-echo-interval 3
lcp-echo-failure 20
">/tmp/var/tmp/options.pppoe
pppd file /tmp/var/tmp/options.pppoe

mfch
DD-WRT Novice

Joined: 04 Jun 2014
Posts: 15

Posted: Sun Jun 15, 2014 8:23 Post subject:
Приветствую! Благодарю за помощь vasek00. Сейчас нет возможности заниматься роутером. Надеюсь в будущем с вашей помощью решить проблему. Прошу Модератора не закрывать и не удалять эту тему.

cher11
DD-WRT Novice

Joined: 19 Jun 2014
Posts: 4

Posted: Thu Jun 19, 2014 1:50 Post subject:

Роутер с такой же проблемой. Запустил скрипт, вот что вывел:

Code:

interface vlan1 does not exist!
bridge name bridge id STP enabled interfaces
br0 8000.f81a67a886ff no eth1
ath0

vasek00
DD-WRT Guru

Joined: 06 Nov 2010
Posts: 3312

Posted: Thu Jun 19, 2014 5:26 Post subject:

cher11 wrote:

Роутер с такой же проблемой. Запустил скрипт, вот что вывел:

Code:

interface vlan1 does not exist!
bridge name bridge id STP enabled interfaces
br0 8000.f81a67a886ff no eth1
ath0

Покажите
swconfig dev ... show
ifconfig

В роутере может стоят чип (CPU) от разных производителей или доп.чип на switch => сетевые интерфейсы поэтому могут иметь разное наименование. Данная команда показала наличие в сетевом интерфейсе br0 = eth1 + ath0

Все что было описано выше относилось к интерфейсам с именами br0, vlan1, vlan2, ath0, у вас же скорей всего интерфейсы имеют имена br0, eth0, eth1, ath0.

cher11
DD-WRT Novice

Joined: 19 Jun 2014
Posts: 4

Posted: Sat Jun 21, 2014 19:53 Post subject:

Спасибо за быстрый ответ. Вот что выдало. К роутеру никаких кабелей сейчас не подключено.

Code:

root@DD-WRT:~# ifconfig
ath0 Link encap:Ethernet HWaddr F8:1A:67:A8:87:00
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:99 errors:0 dropped:0 overruns:0 frame:0
TX packets:116 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:12277 (11.9 KiB) TX bytes:16550 (16.1 KiB)

br0 Link encap:Ethernet HWaddr F8:1A:67:A8:86:FF
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:100 errors:0 dropped:14 overruns:0 frame:0
TX packets:78 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:10853 (10.5 KiB) TX bytes:5861 (5.7 KiB)

br0:0 Link encap:Ethernet HWaddr F8:1A:67:A8:86:FF
inet addr:169.254.255.1 Bcast:169.254.255.255 Mask:255.255.0.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1

eth0 Link encap:Ethernet HWaddr F8:1A:67:A8:86:FF
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:4

eth1 Link encap:Ethernet HWaddr F8:1A:67:A8:87:00
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:5

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MULTICAST MTU:65536 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

Code:

root@DD-WRT:~# swconfig dev ... show
Failed to connect to the switch

Code:

root@DD-WRT:~# swconfig dev eth0 show
Global attributes:
enable_vlan: 0
Port 0:
pvid: 1
link: port:0 link:up speed:1000baseT full-duplex txflow rxflow
Port 1:
pvid: 1
link: port:1 link:down
Port 2:
pvid: 1
link: port:2 link:down
Port 3:
pvid: 1
link: port:3 link:down
Port 4:
pvid: 1
link: port:4 link:down
VLAN 1:
vid: 1
ports: 0 1 2 3 4

Code:

root@DD-WRT:~# swconfig dev eth1 show
Global attributes:
enable_vlan: 0
Port 0:
pvid: 1
link: port:0 link:up speed:1000baseT full-duplex txflow rxflow
Port 1:
pvid: 1
link: port:1 link:down
Port 2:
pvid: 1
link: port:2 link:down
Port 3:
pvid: 1
link: port:3 link:down
Port 4:
pvid: 1
link: port:4 link:down
VLAN 1:
vid: 1
ports: 0 1 2 3 4

vasek00
DD-WRT Guru

Joined: 06 Nov 2010
Posts: 3312

Posted: Sun Jun 22, 2014 6:14 Post subject:
cher11 Из них пока не видно кто из них кто, речь о eth1 и eth0. Нужна тогда марка роутера и его dmesg.

cher11
DD-WRT Novice

Joined: 19 Jun 2014
Posts: 4

Posted: Thu Jun 26, 2014 23:14 Post subject:

Роутер точь-в-точь как у топик стартера.

Code:

TP-Link TL-WR841ND v8

Code:

<5>[ 0.000000] Linux version 3.10.40 (root@dd-wrt.buildserver) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.01 r39555) ) #9975 Tue May 27 11:17:18 CEST 2014
<6>[ 0.000000] bootconsole [early0] enabled
<6>[ 0.000000] CPU revision is: 0001974c (MIPS 74Kc)
<4>[ 0.000000] cpu srif ddr srif cpu 535 ddr 400 ahb 200
<6>[ 0.000000] sys id = 10123 Atheros AR9341 rev 1.3 (0x0123)
<6>[ 0.000000] Determined physical RAM map:
<6>[ 0.000000] memory: 02000000 @ 00000000 (usable)
<4>[ 0.000000] Zone ranges:
<4>[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
<4>[ 0.000000] Movable zone start for each node
<4>[ 0.000000] Early memory node ranges
<4>[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
<7>[ 0.000000] On node 0 totalpages: 8192
<7>[ 0.000000] free_area_init_node: node 0, pgdat 802aabc0, node_mem_map 81000000
<7>[ 0.000000] Normal zone: 64 pages used for memmap
<7>[ 0.000000] Normal zone: 0 pages reserved
<7>[ 0.000000] Normal zone: 8192 pages, LIFO batch:0
<4>[ 0.000000] Primary instruction cache 64kB, 4-way, VIPT, I-cache aliases, linesize 32 bytes.
<4>[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
<7>[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
<7>[ 0.000000] pcpu-alloc: [0] 0
<4>[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
<5>[ 0.000000] Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd init=/sbin/init
<6>[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
<6>[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
<6>[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
<6>[ 0.000000] Writing ErrCtl register=00000000
<6>[ 0.000000] Readback ErrCtl register=00000000
<6>[ 0.000000] Memory: 29196k/32768k available (2093k kernel code, 3572k reserved, 341k data, 188k init, 0k highmem)
<6>[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
<6>[ 0.000000] NR_IRQS:83
<6>[ 0.070000] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248)
<6>[ 0.080000] pid_max: default: 32768 minimum: 301
<6>[ 0.080000] Mount-cache hash table entries: 512
<6>[ 0.090000] NET: Registered protocol family 16
<0>[ 0.490000] 25MHZ ref freq
<6>[ 0.510000] bio: create slab <bio-0> at 0
<6>[ 0.520000] Switching to clocksource MIPS
<6>[ 0.530000] NET: Registered protocol family 2
<6>[ 0.530000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
<6>[ 0.530000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
<6>[ 0.540000] TCP: Hash tables configured (established 512 bind 512)
<6>[ 0.540000] TCP: reno registered
<6>[ 0.540000] UDP hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.550000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 0.560000] NET: Registered protocol family 1
<7>[ 0.560000] PCI: CLS 0 bytes, default 32
<5>[ 0.560000] gpio_proc: module loaded and /proc/gpio/ created
<5>[ 0.570000] wl0gpio_proc: module loaded and /proc/wl0gpio/ created
<6>[ 0.590000] squashfs: version 3.0 (2006/03/15) Phillip Lougher
<6>[ 0.590000] msgmni has been set to 57
<6>[ 0.600000] io scheduler noop registered (default)
<6>[ 0.600000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
<6>[ 0.630000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
<6>[ 0.640000] console [ttyS0] enabled, bootconsole disabled
<0>[ 0.650000] guessed flashsize = 4M
<0>[ 0.650000] scanning for root partition
<0>[ 0.660000] tplink uboot detected
<0>[ 0.660000] guessed bootloader size = 20000
<0>[ 0.670000]
<0>[ 0.670000] found squashfs at 110000
<5>[ 0.680000] Creating 8 MTD partitions on "ar7240-nor0":
<5>[ 0.680000] 0x000000000000-0x000000020000 : "RedBoot"
<5>[ 0.690000] 0x000000020000-0x0000003e0000 : "linux"
<5>[ 0.690000] 0x000000110000-0x0000003d0000 : "rootfs"
<5>[ 0.700000] mtd: partition "rootfs" set to be root filesystem
<5>[ 0.710000] 0x0000003d0000-0x0000003e0000 : "ddwrt"
<5>[ 0.710000] 0x0000003e0000-0x0000003f0000 : "nvram"
<5>[ 0.720000] 0x0000003f0000-0x000000400000 : "board_config"
<5>[ 0.730000] 0x000000000000-0x000000400000 : "fullflash"
<5>[ 0.730000] 0x000000000000-0x000000020000 : "fullboot"
<6>[ 0.740000] libphy: Fixed MDIO Bus: probed
<6>[ 0.750000] tun: Universal TUN/TAP device driver, 1.6
<6>[ 0.750000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
<6>[ 0.760000] PPP generic driver version 2.4.2
<6>[ 0.760000] PPP BSD Compression module registered
<6>[ 0.770000] PPP Deflate Compression module registered
<6>[ 0.770000] PPP MPPE Compression module registered
<6>[ 0.780000] NET: Registered protocol family 24
<6>[ 0.800000] u32 classifier
<6>[ 0.800000] Performance counters on
<6>[ 0.810000] input device check on
<6>[ 0.810000] Actions configured
<6>[ 0.820000] Netfilter messages via NETLINK v0.30.
<6>[ 0.820000] nf_conntrack version 0.5.0 (456 buckets, 1824 max)
<4>[ 0.830000] nf_conntrack_rtsp v0.6.21 loading
<4>[ 0.830000] nf_nat_rtsp v0.6.21 loading
<6>[ 0.840000] ip_tables: (C) 2000-2006 Netfilter Core Team
<6>[ 0.840000] TCP: westwood registered
<6>[ 0.850000] TCP: hybla registered
<6>[ 0.850000] TCP: vegas registered
<6>[ 0.850000] NET: Registered protocol family 17
<5>[ 0.860000] Bridge firewalling registered
<6>[ 0.860000] 8021q: 802.1Q VLAN Support v1.8
<6>[ 0.870000] searching for nvram
<6>[ 0.870000] nvram size = 0
<6>[ 0.900000] Atheros AR71xx hardware watchdog driver version 0.1.0
<6>[ 0.910000] ar71xx-wdt: timeout=15 secs (max=171) ref freq=25000000
<6>[ 0.920000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
<6>[ 0.930000] Freeing unused kernel memory: 188K (802c1000 - 802f0000)
<7>[ 2.880000] ar71xx-wdt: enabling watchdog timer
<6>[ 2.960000] libphy: ag71xx_mdio: probed
<6>[ 3.510000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:00 [uid=004dd042, driver=Generic PHY]
<6>[ 3.520000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
<6>[ 4.080000] ag71xx-mdio.1: Found an AR934X built-in switch
<6>[ 5.110000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
<6>[ 7.390000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
<6>[ 7.390000] Backport generated by backports.git backports-20140320-37-g5c33da0
<6>[ 7.550000] cfg80211: Calling CRDA to update world regulatory domain
<6>[ 7.630000] cfg80211: World regulatory domain updated:
<6>[ 7.640000] cfg80211: DFS Master region: unset
<6>[ 7.640000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 7.650000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 7.660000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 7.670000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 7.670000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 7.680000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 7.690000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
<7>[ 8.130000] ath: EEPROM regdomain: 0x0
<7>[ 8.130000] ath: EEPROM indicates default country code should be used
<7>[ 8.130000] ath: doing EEPROM country->regdmn map search
<7>[ 8.130000] ath: country maps to regdmn code: 0x3a
<7>[ 8.130000] ath: Country alpha2 being used: US
<7>[ 8.130000] ath: Regpair used: 0x3a
<7>[ 8.140000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
<6>[ 8.140000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=78
<6>[ 8.150000] cfg80211: Calling CRDA for country: US
<6>[ 8.170000] cfg80211: Regulatory domain changed to country: US
<6>[ 8.170000] cfg80211: DFS Master region: FCC
<6>[ 8.180000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 8.190000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
<6>[ 8.190000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
<6>[ 8.200000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (N/A)
<6>[ 8.210000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
<6>[ 8.220000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
<6>[ 10.250000] device br0 entered promiscuous mode
<6>[ 12.370000] device eth1 entered promiscuous mode
<6>[ 12.380000] device br0 left promiscuous mode
<6>[ 12.390000] device br0 entered promiscuous mode
<6>[ 12.440000] cfg80211: Calling CRDA to update world regulatory domain
<3>[ 12.470000] cfg80211: Invalid regulatory domain detected:
<6>[ 12.470000] cfg80211: Regulatory domain: 00
<6>[ 12.480000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 12.480000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 12.490000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 12.500000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 12.510000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 12.520000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 12.530000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
<6>[ 12.560000] cfg80211: Calling CRDA to update world regulatory domain
<6>[ 12.580000] cfg80211: World regulatory domain updated:
<6>[ 12.590000] cfg80211: DFS Master region: unset
<6>[ 12.590000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 12.600000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 12.610000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 12.620000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 12.630000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 12.640000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 12.640000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
<6>[ 12.670000] cfg80211: Calling CRDA for country: US
<6>[ 12.700000] cfg80211: Regulatory domain changed to country: US
<6>[ 12.710000] cfg80211: DFS Master region: FCC
<6>[ 12.710000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 12.720000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
<6>[ 12.730000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
<6>[ 12.740000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (N/A)
<6>[ 12.750000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
<6>[ 12.750000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
<6>[ 15.910000] device ath0 entered promiscuous mode
<6>[ 15.910000] br0: port 2(ath0) entered forwarding state
<6>[ 15.920000] br0: port 2(ath0) entered forwarding state
<6>[ 15.980000] device br0 left promiscuous mode
<6>[ 16.860000] device eth0 entered promiscuous mode
<6>[ 16.950000] device eth0 left promiscuous mode
<6>[ 17.920000] br0: port 2(ath0) entered forwarding state
<6>[ 2237.310000] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.
<6>[ 2311.930000] device eth1 left promiscuous mode
<6>[ 2311.940000] br0: port 1(eth1) entered disabled state
<6>[ 2311.960000] device ath0 left promiscuous mode
<6>[ 2311.960000] br0: port 2(ath0) entered disabled state
<6>[ 2314.330000] device br0 entered promiscuous mode
<6>[ 2316.460000] device eth1 entered promiscuous mode
<6>[ 2316.470000] device br0 left promiscuous mode
<6>[ 2316.480000] device br0 entered promiscuous mode
<6>[ 2318.820000] cfg80211: Calling CRDA to update world regulatory domain
<3>[ 2318.850000] cfg80211: Invalid regulatory domain detected:
<6>[ 2318.850000] cfg80211: Regulatory domain: 00
<6>[ 2318.860000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 2318.870000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 2318.880000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 2318.890000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 2318.890000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 2318.900000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 2318.910000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
<6>[ 2318.940000] cfg80211: Calling CRDA to update world regulatory domain
<6>[ 2318.970000] cfg80211: World regulatory domain updated:
<6>[ 2318.970000] cfg80211: DFS Master region: unset
<6>[ 2318.980000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 2318.990000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 2318.990000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 2319.000000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 2319.010000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 2319.020000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
<6>[ 2319.030000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
<6>[ 2319.050000] cfg80211: Calling CRDA for country: US
<6>[ 2319.080000] cfg80211: Regulatory domain changed to country: US
<6>[ 2319.080000] cfg80211: DFS Master region: FCC
<6>[ 2319.090000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
<6>[ 2319.100000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
<6>[ 2319.100000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
<6>[ 2319.110000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (N/A)
<6>[ 2319.120000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
<6>[ 2319.130000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
<6>[ 2321.990000] device ath0 entered promiscuous mode
<6>[ 2322.390000] br0: port 2(ath0) entered forwarding state
<6>[ 2322.400000] br0: port 2(ath0) entered forwarding state
<6>[ 2322.500000] device br0 left promiscuous mode
<6>[ 2324.400000] br0: port 2(ath0) entered forwarding state

vasek00
DD-WRT Guru

Joined: 06 Nov 2010
Posts: 3312

Posted: Fri Jun 27, 2014 6:17 Post subject:

WAN порт в данном случае на этом роутере не получиться как либо перестроить, так как данная команда предназначена для управления switch (коммутатором) которые подключены к CPU например так:
Switch-----eth1-CPU-eth0(WAN)
LAN1
LAN2
LAN3
LAN4

в вашем случае имеем сам switch в самом CPU
CPU-eth0(WAN)
LAN1
LAN2
LAN3
LAN4

Настройки switch/коммутатора в Atheros происходят через регистры при загрузке uboot, и такой программы/команды для управления ими из прошивки dd-wrt нет.
Данные команды которые описаны выше (swconfig dev eth...) применимы для управления внешним switch который подключен к CPU и сидит например на интерфейсах eth1.

Goto page 1, 2, 3, 4, 5 Next

Display posts from previous:

Page 1 of 5

DD-WRT Forum Index -> Оборудование на основе Atheros WiSOC

All times are GMT

Navigation

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum

Log in

TP-Link TL-WR841ND v8 переназначить WAN

Quick Links

Log in