please help me!!!! bricked wrt160nl!

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Atheros WiSOC based Hardware
Author Message
rovanda
DD-WRT Novice


Joined: 25 Apr 2014
Posts: 5

PostPosted: Fri Apr 25, 2014 14:14    Post subject: please help me!!!! bricked wrt160nl! Reply with quote
died wrt160nl7 hrs, 8 min. Days ago Karma : 0
Hello, dear friends !

I have the following problem
After pouring the firmware from openwrt played with the settings , but that is spoiled
did not work from the web admin panel lucib but ping router
After trying to pour through tftp firmware and the router is no longer pinged
No reset has not helped
Found wire dku- 5 nokia original, bungled postings to connect to the console port
putti but does not connect with the router , just a black screen . What can you need to do the port settings ?
Put the original driver for WinXP, WinXP system itself as found wood for Vin7 .

Wires were the black, yellow , blue, white, red
respectively black I connected to GND, white and blue to rx and tx, try to swap them nothing.
Maybe something wrong doing ? help please!
with respect,
Maxim


U-Boot 1.1.6 (Apr 14 2010 - 14:02:36)
DRAM: ar7100_ddr_initial_config(237) enter!
ar7100_ddr_initial_config(269) exit!
U-Boot 1.1.6 (Apr 14 2010 - 14:02:36)
AP81 (ar7100) U-boot
sri
32 MB
WRT160NL u-boot version: 1.0.0
Top of RAM usable for U-Boot at: 82000000
Reserving 279k for U-Boot at: 81fb8000
Reserving 192k for malloc() at: 81f88000
Reserving 44 Bytes for Board Info at: 81f87fd4
Reserving 36 Bytes for Global Data at: 81f87fb0
Reserving 128k for boot params() at: 81f67fb0
Stack Pointer at: 81f67f98
Now running in RAM - U-Boot at: 81fb8000
id read 0x100000ff
flash size 8MB, sector count = 128
Flash: 8 MB
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: ag7100_enet_initialize...
ag7100 get ethaddr for device eth0
Fetching MAC Address from 0x81feb1e0
--------***** Get the RTL8306SD Manufactory ID=379c *****-------
Reg6: speed=0 nway=1 duplex=0
Reg5: speed=0 nway=0 duplex=0
Reg1: a1=7fd9 a2=30e0 a3=15ac a4=30e0 a5=0
Reg1: a1=7fd9 a2=30e0 a3=15ac a4=30e0
Reg1: a1=7fd9 a2=30e0 a3=15ac a4=30e0
Reg1: a1=7fd9 a2=30e0 a3=15ac a4=30e0
Reg1: a1=7fd9 a2=30e0 a3=15ac a4=30e0
eth0: c0:c1:c0:dd:12:fd
eth0 up
eth0
### main_loop entered: bootdelay=1
Hit any key to stop autoboot: 1  0


here i need to press the enter but does not respond, and loaded on the team I can not vvodit.kak relieve this situation?
Sponsor
rovanda
DD-WRT Novice


Joined: 25 Apr 2014
Posts: 5

PostPosted: Fri Apr 25, 2014 14:29    Post subject: Reply with quote
this is my log

U-Boot 1.1.6 (May 12 2009 - 07:52:2Cool

DRAM: ar7100_ddr_initial_config(237) enter!
ar7100_ddr_initial_config(269) exit!


U-Boot 1.1.6 (May 12 2009 - 07:52:2Cool

AP81 (ar7100) U-boot
sri
32 MB
WRT160NL u-boot version: 1.0.0
Top of RAM usable for U-Boot at: 82000000
Reserving 279k for U-Boot at: 81fb8000
Reserving 192k for malloc() at: 81f88000
Reserving 44 Bytes for Board Info at: 81f87fd4
Reserving 36 Bytes for Global Data at: 81f87fb0
Reserving 128k for boot params() at: 81f67fb0
Stack Pointer at: 81f67f98
Now running in RAM - U-Boot at: 81fb8000
id read 0x100000ff
flash size 8MB, sector count = 128
Flash: 8 MB
*** Warning - bad CRC, using default environment

In: serial
Out: serial
Err: serial
Net: ag7100_enet_initialize...
ag7100 get ethaddr for device eth0
Fetching MAC Address from 0x81feb1e0

--------***** Get the RTL8306SD Manufactory ID=379c *****-------
Reg6: speed=0 nway=1 duplex=0
Reg5: speed=0 nway=0 duplex=0
Reg1: a1=7fd9 a2=30e0 a3=15ac a4=30e0 a5=0
Reg1: a1=7fd9 a2=30e0 a3=15ac a4=30e0
Reg1: a1=7fd9 a2=30e0 a3=15ac a4=30e0
Reg1: a1=7fd9 a2=30e0 a3=15ac a4=30e0
Reg1: a1=7fd9 a2=30e0 a3=15ac a4=30e0
eth0: 68:7f:74:9b:32:00
eth0 up
eth0
### main_loop entered: bootdelay=1

Hit any key to stop autoboot: 0
## Booting WRT160NL ...
Application code length 0x0000ffe0
CRC OK
## Booting image at bf04003c ...
Image Name: MIPS OpenWrt Linux-2.6.32.27
Created: 2011-12-21 1:03:59 UTC
Image Type: MIPS Linux Kernel Image (gzip compressed)
Data Size: 1242866 Bytes = 1.2 MB
Load Address: 80060000
Entry Point: 80060000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
kernel: org len = 1242866, new len = 1245184
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 33554432

Starting kernel ...

Linux version 2.6.32.27 (jow@nd-build-02.linux-appliance.net) (gcc version 4.3.3 (GCC) ) #5 Wed Dec 21 01:59:33 CET 2011
bootconsole [early0] enabled
CPU revision is: 00019374 (MIPS 24Kc)
Atheros AR9130 rev 2, CPU:400.000 MHz, AHB:200.000 MHz, DDR:400.000 MHz
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Kernel command line: rootfstype=squashfs,yaffs,jffs2 noinitrd console=ttyS0,115200 board=WRT160NL
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 29276k/32768k available (2126k kernel code, 3492k reserved, 423k data, 152k init, 0k highmem)
SLUB: Genslabs=7, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:56
Calibrating delay loop... 266.24 BogoMIPS (lpj=1331200)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
MIPS: machine is Linksys WRT160NL
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) б╘ 2001-2006 Red Hat, Inc.
yaffs Dec 10 2011 18:14:12 Installing.
msgmni has been set to 57
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
Atheros AR71xx SPI Controller driver version 0.2.4
m25p80 spi0.0: mx25l6405d (8192 Kbytes)
Searching for RedBoot partition table in spi0.0 at offset 0x7e0000
Searching for RedBoot partition table in spi0.0 at offset 0x7f0000
No RedBoot partition table detected in spi0.0
6 wrt160nl partitions found on MTD device spi0.0
Creating 6 MTD partitions on "spi0.0":
0x000000000000-0x000000040000 : "u-boot"
0x000000040000-0x000000170000 : "kernel"
0x000000170000-0x0000007e0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=350000, len=490000
0x000000350000-0x0000007e0000 : "rootfs_data"
0x0000007e0000-0x0000007f0000 : "nvram"
0x0000007f0000-0x000000800000 : "art"
0x000000040000-0x0000007e0000 : "firmware"
ag71xx_mdio: probed
eth0: Atheros AG71xx at 0xb9000000, irq 4
Registering RTL8306SD switch with Chip ID: 0x5988, version: 0x0000
eth1: Atheros AG71xx at 0xba000000, irq 5
Atheros AR71xx hardware watchdog driver version 0.1.0
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 152k freed
Please be patient, while OpenWrt loads ...
input: gpio-buttons as /devices/platform/gpio-buttons/input/input0
Button Hotplug driver version 0.3.1
- preinit -
Registered led device: wrt160nl:blue:power
Registered led device: wrt160nl:amber:wps
Registered led device: wrt160nl:blue:wps
Registered led device: wrt160nl:blue:wlan
Press the [f] key and hit [enter] to enter failsafe mode
eth0: link up (100Mbps/Full duplex)
- regular preinit -
switching to jffs2
mini_fo: using base directory: /
mini_fo: using storage directory: /overlay
- init -
eth0: link down

Please press Enter to activate this console. device eth0 entered promiscuous mode
device eth1 entered promiscuous mode
Compat-wireless backport release: compat-wireless-2011-11-08-1-g4ab9b62
Backport based on wireless-testing.git master-2011-11-15
cfg80211: Calling CRDA to update world regulatory domain
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
eth0: link up (100Mbps/Full duplex)
br-lan: port 1(eth0) entering forwarding state
usbcore: registered new device driver usb
ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2122 RF Rev:a2 mem=0xb80c0000, irq=2
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
cfg80211: World regulatory domain updated:
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: Calling CRDA for country: US
NET: Registered protocol family 24
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ar71xx-ehci ar71xx-ehci: Atheros AR91xx built-in EHCI controller
ar71xx-ehci ar71xx-ehci: new USB bus registered, assigned bus number 1
ar71xx-ehci ar71xx-ehci: irq 3, io mem 0x1b000000
ar71xx-ehci ar71xx-ehci: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
cfg80211: Regulatory domain changed to country: US
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
nf_conntrack version 0.5.0 (459 buckets, 1836 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
device wlan0 entered promiscuous mode
br-wan: port 2(wlan0) entering forwarding state
device wlan0 left promiscuous mode
br-wan: port 2(wlan0) entering disabled state
device wlan0 entered promiscuous mode
br-wan: port 2(wlan0) entering forwarding state
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Atheros WiSOC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum