need help,dir-615 g2 keep revert stock fw after reboot

Post new topic   Reply to topic    DD-WRT Forum Index -> Ralink SoC based Hardware
View previous topic :: View next topic  
Author Message
kiffhcq
DD-WRT Novice


Joined: 12 Dec 2014
Posts: 3
PostPosted: Fri Dec 12, 2014 4:36    Post subject: need help,dir-615 g2 keep revert stock fw after reboot Reply with quote
I heve flashed my dir-615 g2 to ddwrt r19519 and it all working well but everytime i power off or reboot router it keep revert to d-link stock firmware,is tat anything wrong with my router?

Thanks for advance
Back to top View user's profile Send private message
Sponsor
kiffhcq
DD-WRT Novice


Joined: 12 Dec 2014
Posts: 3
PostPosted: Sun Dec 14, 2014 7:22    Post subject: Reply with quote
eibgrad wrote:
That doesn’t seem possible. Once you update to dd-wrt firmware, the prior firmware is lost and would require reinstallation, by YOU. A mere reboot isn’t going to make the old firmware reappear. So your description doesn’t jive w/ how the firmware update process actually works.


I flashed my router use emergency rom update
Set my pc ip to 192.168.0.50
Power off my router
Press reset button for 5 sec.then power on my router without release and wait 10sec.till then power icon led blinking
Plug in my lan cable to the wan port of my router
Open address 192.168.0.1 with ie
Choose the firmware to update
All done n boot into ddwrt,doing factory reset then it will revert back to d-link stock fitmware
Nvm,i flash again,when reach step factory reset happen again
Blur with whay happen to my router,hope got solution from here
Thanks for advance
Back to top View user's profile Send private message
bob8
DD-WRT User


Joined: 28 Jul 2012
Posts: 69
PostPosted: Sun Dec 14, 2014 8:09    Post subject: Reply with quote
Sounds like your G2 perhaps stores two separate firmware images.

Just a suggestion, but have you tried flashing the router twice to see if it will overwrite the second stock image?

eg. perform the second flash via the DD-WRT GUI.
Back to top View user's profile Send private message
kiffhcq
DD-WRT Novice


Joined: 12 Dec 2014
Posts: 3
PostPosted: Sun Dec 14, 2014 8:30    Post subject: Reply with quote
bob8 wrote:
Sounds like your G2 perhaps stores two separate firmware images.

Just a suggestion, but have you tried flashing the router twice to see if it will overwrite the second stock image?

eg. perform the second flash via the DD-WRT GUI.


Thanks for reply
I have try after flashed r19519 then upgrade to latest ddwrt firmware also,same issue
Back to top View user's profile Send private message
bob8
DD-WRT User


Joined: 28 Jul 2012
Posts: 69
PostPosted: Sun Dec 14, 2014 9:31    Post subject: Reply with quote
I noticed you installed via Emergency Room.

Is this link any help where flashing via Dlink stock GUI was successful using a different login username?

http://cakegiyh.blogspot.co.uk/2014/01/flash-unifi-router-dir-615-g2-to-dd-wrt.html
Back to top View user's profile Send private message
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Index -> Ralink SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum