Posted: Sun May 30, 2021 12:03 Post subject: New Build - 05/30/2021 - r46816
[WARNING]: This thread is only for feedback on this beta release for developers and the community's benefit.
DO NOT flash this beta release unless you understand the risks involved and device specificrecovery methods.
Avoid discussions! Create threads for questions, general problems or use search; this thread is not for support.
Please list router model & revision, operating & wireless mode(s) and exact filename/firmware image flashed.
Issues, observations, and/or workarounds reported:
• DNScrypt 1.95 can still be used in the GUI, but v2 (not compatible) requires Golang and thus Entware. #6246
• WDS does not work on Broadcom ARM devices(only MIPS<->MIPS) & bridge modes on k4.4 devices may sometimes work
in some configurations for certain builds but are not supported by the bcmdhd driver. Use client or repeater instead.
• VAPs not working at bootfixed for unbridged VAPs in40562 - 40566. Effective startup commandsdiscussion thread is here.
• If start-up scripts do not work from USB add a delay, e.g. wait script or 'sleep 25'.
• Broadcom ARM devices if 5 GHz channels are missing, via Telnet/SSH: 'nvram set brcm_unlock=1' 'nvram commit' 'reboot'
• Show us your findings with steps to reproduce, configuration, output, logs and important information below!
Important:
• For issues provide applicable info: 'dmesg', 'cat /tmp/var/log/messages', syslog, klog, serial, strace, tcpdump, wireshark etc.
• Any firewall NAT or WAN issues, show output: 'iptables -vnL', 'iptables -t nat -vnL', 'iptables -t mangle -vnL' and /tmp/.ipt file.
• Search SVN tickets & discuss in forum before opening. Before reporting: reset & manually set up, not restore from a backup.
• Please include operating & wireless modes (e.g. Gateway, Router, AP, CB, WDS, Mesh) & relevant configuration information.
Router/Version: D-Link DIR-868L Rev.A1 File/Kernel: dir868a-webflash.bin/ Linux 4.4.269 #3242 SMP Sun May 30 03:22:26 +07 2021 armv7l
Previous/Reset: DD-WRT v3.0-r46788 std (05/28/21)/ no
Mode/Status: Repeater Bridge on 5GHz AC/N-Mixed (wl0 is purposely turned off) + USB Storage + lighttpd + ProFTPD + cron / working
Issues/Errors: router stopped working after accessing control panel page
It's a bit strange and I don't know which part caused the issue, so please read the sequence of events below:
1. upgrade from r46788 to r46816: lighttpd is still working, ftp is still working, and I can still access ddwrt control panel
2. on ddwrt control panel, I switch to service tab > USB : router stops responding : telnet connection is dropped, wifi down, cannot open any web page including ddwrt control panel (sorry I forgot to ping)
3. after restarting router, lighttpd is working again, ftp is working again, telnet is working again, but startup script doesn't run. However, The moment I open ddwrt control panel main page (not services > USB page) then the router stops responding again.
4. downgrading to r46788 : everything are working again (lightttpd, ftp, startup script are working, ddwrt is accessible for all pages)
5. after upgrading to r46816: same as 3
6. downgrading to r46788 : same as 4. now i'm still on r46788
I tried to tail -f /tmp/var/log/messages but nothing showed up when the router stopped responding
I still don't understand why i could access ddwrt control panel for the first time (item 1 above) then subsequently it's inaccessible (even with internet explorer)
edit: my pc is connected to the router via Ethernet cable connected to LAN 1
edit 2: lighttpd is using port 80 & 443, and i change the webui port to 8080 as in this discussion https://forum.dd-wrt.com/phpBB2/viewtopic.php?p=80468
my current setting:
Joined: 18 Mar 2014 Posts: 12915 Location: Netherlands
Posted: Sun May 30, 2021 12:46 Post subject:
Router Model: Netgear R6400v1
Firmware Version: DD-WRT v3.0-r46816M Community Build (05/30/21)
Kernel Version: Linux 4.4.269 #1 SMP Sun May 30 12:42:13 CEST 2021 armv7l
Upgraded from: DD-WRT v3.0-r46772M Community Build (05/26/21)
Reset: No, not this time
Status: Up and running for 2 hours, basic setup as Gateway, static leases, 2.4 GHz and 5 GHz working.
Running one WireGuard tunnel to Keepsolid and second WireGuard tunnel to own WG server for site-to-site connection.
OpenVPN client tested and working.
Errors: No, not at this moment.
Joined: 18 Mar 2014 Posts: 12915 Location: Netherlands
Posted: Sun May 30, 2021 13:34 Post subject:
Router Model: Netgear R6400v2, board_id: U12H332T
Firmware Version: DD-WRT v3.0-r46816M Community Build (05/30/21)
Kernel Version: Linux 4.4.269 #1 SMP Sun May 30 12:42:13 CEST 2021 armv7l
Upgraded from: DD-WRT v3.0-r46772M Community Build (05/26/21)
Reset:Yes did a reset with nvram erase && reboot
Status: Up and running for 2 hours, basic setup as Gateway, static leases, OpenVPN client with Policy Based Routing up and running, 2,4GHz and 5Ghz working, USB storage working, OpenVPN server working, WireGuard server working with 8 clients (phones , windows and two other routers for site-to-site setup).
Joined: 14 Sep 2019 Posts: 301 Location: Maine, USA
Posted: Sun May 30, 2021 13:51 Post subject:
Router/Version: Asus RT-N12D
File: dd-wrt.v24-#####_NEWD-2_K3.x_mega.bin
Firmware: DD-WRT v3.0-r46816 mega (05/30/21)
Kernel: Linux 4.4.269 #9704 Sun May 30 06:37:47 +07 2021 mips
Mode: Default settings
Previous: r46442
Reset?: Y
Status: Not working, no WAN IP assigned. Last working version is r46442. Did a few "nvram clear && reboots".
Posted: Sun May 30, 2021 14:16 Post subject: Netgear Nighthawk R7000
Router/Version: Netgear R7000 Firmware: DD-WRT v3.0-r46816 std (05/30/21) Kernel: Linux 4.4.269 #3242 SMP Sun May 30 03:22:26 +07 2021 armv7l Mode: Gateway, Wireless AP. CTF & FA Enabled. NAT and QOS Off. Reset: Nope. Previous: 05-25-2021-r46750 Status: Working so far; better temperatures at the moment, still testing. Something strange in dmesg. I included a log from the initial flash and another one at the end of the usual logs, after a power cycle. Temperatures: CPU 60.2 °C / WL0 47.5 °C / WL1 52.9 °C
Logs.txt
Description:
Full system logs. MAC scrubbed, password scrubbed, the fun stuff at the bottom as usual!
Joined: 14 Sep 2019 Posts: 301 Location: Maine, USA
Posted: Sun May 30, 2021 14:25 Post subject:
egc wrote:
Just a wild guess, set:
pppoe_ifname=vlan1
pppoe_wan_ifname=vlan1
to vlan2:
nvram set pppoe_ifname=vlan2
nvram set pppoe_wan_ifname=vlan2
If it works:
nvram commit
what is the output of
Code:
get_wanface
root@DD-WRT:~# get_wanface
vlan1
I tried manually setting the parameters you mentioned, amongst others. It seems the boot process determines that vlan0=lan and vlan1=wan and resets the important parameters to reflect it. The router is running with default settings with just sshd and syslog enabled to keep it simple.
Router Model / Version: Netgear R6300V2
Previous Firmware:DD-WRT v3.0-r46788 std (05/28/21)
Current Firmware: DD-WRT v3.0-r46816 std (05/30/21)
File: netgear-r6300v2-webflash.bin / CLI Flash (easyddup.sh)
Kernel: Linux 4.4.269 #3242 SMP Sun May 30 03:22:26 +07 2021 armv7l
Reset: No
Wireless: Disabled
Routing: Operating - Gateway (WAN PPPoE)
Setup: SFE, NTP, DDNS (inadyn-Entware), Wireguard Server
Services: DNSMasq (GUI+ additional options on USB, Lighttpd, Syslog, SSH, FreeRadius, Telnet, USB, ProFTPD (with users), Samba (with users), Adblock for DD-WRT by Yamaraj, OpenVPN Client
Security: Firewall Enabled
NAT/QoS: HTB + FQ_CODEL
Administration:Remote Access (HTTPS & SSH), Startup Script (For DNSMasq & inadyn)
Uptime: up 1:01, load average: 0.23, 0.10, 0.08
Temperature: CPU 74.7 °C / Not available
Status: OK
Issues: None
All good with this build. I can confirm the port order have been fixed on the Netgear R6300v2 starting with this build. The gui/config matches the physical ports.
Router/Version: Netgear R6250
Firmware: DD-WRT v3.0-r46816 std (05/30/21)
Kernel:Linux 4.4.269 #3242 SMP Sun May 30 03:22:26 +07 2021 armv7l
Mode: Gateway, Wireless AP, unbound
Reset: No, not this time
Previous : r46788
Upgrade: Web and 1st succeed without reset.
Temperatures CPU 74.7 °C / WL1 55.0 °C
Load: 0.08, 0.01, 0.00
Uptime 1 hour
Errors: No, not at this moment.
WAN: DHCP
MTU:1500 Auto
Shortcut Forwarding Engine: CTF
Flow Acceleration: CTF & FA
STP: Disable
DHCP Server Enabled - Running
Samba Disabled
WRT-radauth Disabled
WRT-rflow Disabled
MAC-upd Disabled
CIFS Automount Disabled
Sputnik Agent Disabled
USB Support Disabled
Router/Version: Asus RT-AC3100
File/Kernel: asus_rt-ac3100-firmware.trx(experimental)/Linux 4.4.269 #3250 SMP Sun May 30 06:19:12 +07 2021 armv7l
Previous/Reset: r46788/No
Mode/Status: NAT,Wireguard client,uPNP,no DNS/DHCP,static WAN IP,G/N VHT40 2.4GHz, A/AC VHT80 5GHz
Issues/Errors: Same as before: ports reversed, port 5 & 6 nonexistent but showing. Otherwise, appears to be working correctly.
Update: Router just rebooted on its own, at about 24 hours. This has not happened for many, many versions so definitely a potential issue.
Last edited by PeteSL on Mon May 31, 2021 12:08; edited 1 time in total
Posted: Sun May 30, 2021 19:19 Post subject: Asus RT-AC87U
Router/Version: Asus RT-AC87U
File/Kernel: asus_rt-ac87u-firmware.trx
Previous/Reset: r46733
Mode/Status: WAP, wg-client, 2.4+5G, DHCP server, SFE on, no fancy config
Issues/Errors: unusable
Unusable for me.
First no GUI access (via LAN), but wg and internet OK. 3 times off/on, then ssh-access and GUI for some time. Took LOGs, see attachment.
wifi: SSIDs were sent, but no device could connect. Access lost entirely after F5 on tab Tunnels.
Reset by button, restored previous config, same issue.
Router/Version: Netgear R7000
Firmware: DD-WRT v3.0-r46816 std (05/30/21)
Kernel: Linux 4.4.269 #3242 SMP Sun May 30 03:22:26 +07 2021 armv7l
Previous: r46788
Mode/Status: Gateway / working
Issues/Errors: Working well so far.
Uptime: 4hrs 16mins
Upgrade: via web UI, no issues
Reset: no
Temperatures: CPU 68.0 °C / WL0 46.5 °C / WL1 52.5 °C
Router/Version: Tplink Archer C1900
File/Kernel: archer-c1900-webflash.bin
Previous/Reset: 05-09-2021-r46604 nvram erase after upgrade
Issues/Errors: After I upgraded I wasn't getting a wan IP. I did an nvram erase && reboot and I still had the issue. I waited a bit and reset my modem and router and I still had the issue so I decided to reset one more time because I was half asleep when I set up my router so I thought maybe I set something up wrong. After the 2nd reset everything seems ok so I don't know what happened. I see some people saying they have similar issues because of the new swconfig update so I ran those commands that were recommended to show the vlan configuration. I have no idea if this is of any use but here they are.