[Tornado]

I have decided that after working on Tjtag for almost 6 years, and very few donations, that tjtag will only be available from http://tjtag.com

In order to receive tjtag, I will require a min. $5.00 donation, to help me cover cost. You may contact me with your requests, and for help with processors not in tjtag at my e-mail address tornado@tjtag.com

I'm sorry it has come to this....

Regards,

Tornado


Tjtag 3.0.2 RC2-5 soon to be available

Tjtagv 3.0.1 Released Aug-30-2009

Please read changelog in the docs directory

Tjtagv3 Released Aug-26-2009

Tjtagv3 final pulled because of an error found, I will post a new version 3.0.1 shortly. tjtagv3 final had a typo in it that caused it to write backup data twice - do no not trust your backup, it has been fixed and tested.



Tjtagv2.1.4 Released Mar-21-2008

Tjtagv2 Released Jan-16-2008

Files are located in the download section

Downloads -->>others-->>tornado-->>jtag

As always, please leave feedback, its how we improve..

Your Support for Tjtag and Tornado!

P.S> Special thanks to Eko, BS, Redhawk, Barryware, Sash and all the members that helped me test.

PPS. maybe interesting jtag discussions here and here

[Honki]

can i use it for JTAG FON 2100 too?

[dexter4000]

great work Tornado

[Wingit]

Ok I'm not to sure what command line to issue for debricking a wrt54gs 7.
Could someone help with this.
I'm trying
tjtag -flash:wholdflash /skipdetect /fc:11 and it sticks at block 1, and 6 lights on.

Could someone help out?

[xircommy]

Wingit

I use this commands give by Tornado "tjtag -backup:cfe /noreset or tjtag -backup:cfe /noemw" but you need change "-backup:cfe to -flash:wholeflash /noreset or flash:wholeflash /fc:11 /noreset" if doesn't work.
from now I hope you get lucky.

[Tornado]

@Wingit

xircommy, is right, except - I am changing the flash definitions all the time, so / FC:11 may not be your flash chip. run Tjtag with a -probeonly /noemw to see if it detects your flash chip.

If it does you can continue, if it doesnt, just run Tjtag alone with no switches, it will list all the available flash chips it knows about, then you can choose the correct one for your router.

I use "For the GSv6 and that processor"

Tjtag -flash:cfe /noreset

Also, you do not need to flash wholeflash, only the BSP "If you have one for your router" and you do not need /skipdetect or the /fc switch, everything you need is already in tjtag for that router.

[Wingit]

Thanks for the help.

I tried the tjtag -probleonly /noreset and it found every thing just fine. then tried the -flash:wholeflash /noreset, currently it appears to be flashing because I have chip locations scrolling on the screen. but there are no lights flashing. So either it's not loading or it is. will see what happens when it's completed


Fingers crossed

Thanks
xircommy
Tornado

[Wingit]

currently at 17 %

[Wingit]

ok it stopped at 22% 1fc751d0, oh well. But the lights are on now. Before they would not stay on. Thats good

[Wingit]

Ok tried it again with the command tjtag -erase:wholeflash /noreset, this time it erased the 39 blocks but before it would not, and then started flashing the chip. So lets see were it takes me this time. Currently at 2 %.

[Wingit]

ok it stopped at 54% 1fd17900,. Ok so tjtag -erase:wholeflash /noreset again. My thought is it its cleaning more and more so I will run the command again.

Sorry if I'm posting to much on the same subject but I was thinking it might help someone else out as to what I'm running into. So please bare with me.

[Tornado]

Read your PM's, also if you are flashing an original wholeflash then you don't need to flash anything else, @ %50 you have the BSP on, and just need to give it the firmware thru the mgmt console.

[Wingit]

It completed and at 1 hour 14 min.
Great that was my next question. I will check it thru the mgmt console and let you know. Also 5 lights remain on.

[Tornado]

If you put a whole flash on it, meaning your original backip, and you have 5 lights on then either the backup is bad or the flash was ! I don't recommend flashing a wholeflash, just the BSP, then you can install the original firmware thru the MGMT console.

[Wingit]

Ok you are going to have to run me thru that, Please

Thanks

I have the linksys firmware file. I also emailed you.