I am well aware of this method. I call this destructive chip removal. And it only works for QFP and not with TSOP(II) packages. If unshure, try above method and mine with surplus SDRAM module for practice, before even trying to remove chips from router board.
For cheap non-destructive desoldering I would recommend butane solder torch like Iroda SolderPRO 70 with some home made alu screening.
Last edited by oleo on Tue Mar 13, 2007 9:43; edited 1 time in total
i added these lines (the only ones from your config that could improve browsing speed)
socket options = TCP_NODELAY SO_RCVBUF=8192 SO_SNDBUF=8192
local master = no
os level = 33
domain master = yes
preferred master = yes
nothing...router hits 100% CPU utilization when trying to browse samba
I am not using samba mounted on asus from remote server it was a wrong expression
all i wanted was options in samba config that could improve asus samba share browsing speed from XP machine
obviously there arent any and samba is terribly slow (too slow to be used)
unless im wrong
PS and something off topic ... i disable radio with the EZ setup button (dd-wrt) and i give command wl radio
i get radio is off (WL_RADIO_SW_DISABLE 1 WL_HW_DISABLE_0)
(when operating normaly it is WL_RADIO_SW_DISABLE 0 WL_HW_DISABLE_0)
that means that the radio is transmitting although invisible to other PCs ?
what is radio hardware disable ?
I am attaching global part of my samba2 master browser on Oleg firmware:
Code:
[global]
interfaces = br0
bind interfaces only = yes
workgroup = WORKGROUP
guest account = nobody
security = share
browseable = yes
guest ok = yes
guest only = yes
log level = 2
log file = /opt/var/log/smbd-%m.log
max log size = 100
local master = true
preferred master = true
os level = 65
encrypt passwords = no
preserve case = yes
short preserve case = yes
server string = "OLEO NAS"
[share]
path = /tmp/harddisk
comment = "Whole disk (read-only)"
....
Browing work seamlesly. I never hit any percentage for browsing. Only smbd takes up 40% of CPU at transfer.
Youl could also try smbclient -L 192.168.1.1 -N to list your shares and smbclient //192.168.1.1/share -N to connect.
Maybe there is a problem that you do not have DNS server configured and that this slows down browsing. Edit /etc/hosts , add hosts and enable dnsmasq local DNS.
at transfer i get about 75-90%
maybe its a memory thing ? are you getting this number on the 64 MB upgraded router ?
i am running traqnsmissiond at the same time and i have always free memory less than 800-900kB
dns cannot be a reason in this once the transfer has started
man its crazy...do you know what it seems that was the cause of this ?
Logging level set to 8 by default...after set it to 3 like you it was better and now i set to 0 its almost OK
how should i have suspected that such a 'light' operation like logging would have such a big impact ?
a few things more....user nobody seems to not be able to create directories and save in the samba shares...shouldnt he be able to ? i have Read Only set to No do i need to set permissions too ?
can you help me with the other issue as well ?
why my wl-500gP in Client mode doesnt pick up ANY SSID.... even stations in the same room that are "shouting up its ear"
nothing
in AP it works ok
default log level is 0 as shipped with default config with samba2. Setting to 8 was done by you. This is not very clever thing to do even on full featured linux server.
For writtable guest shares with increased leve of security I recommend force user option and setting /etc/group for non samba access permissions.
I recommend client bridge mode not client itself. There is no automatic association unless SSID is set the same as the AP SSID.
my problem is that either Client or Client Bridge mode DONT work
i set the WRT and WL-500gP side by side (wrt with v23sp2 and WL-500gP with V23sp3)
and they dont detect the other with scan
both work fine in AP mode (linksys has not as good radio as the asus)
but in Client mode they dont detect anything
Even in AP mode the scan doesnt find anything only other clients (network cards , laptopts) can find them and connect to them (with no problem)
also do you know what it means in command
wl radio
radio is on (WL_RADIO_SW_DISABLE 0 WL_HW_DISABLE 0)
--->
the WL_HW_DISABLE_0 can never be 1 (HW=hardware ?)
(when you switch the radio off the WL_SW_DISABLE 0 becomes 1)
this means that the radio is NEVER really OFF it just isnt transmitting any data
(and thats why it isnt detected) when you switch it off (either by web interface or by the EZ setup button)
maybe the modulation and the transmitter is always ON which is a bad thing if
you have it inside your room like i do and you just want to turn radio on occasionally to connect with the laptop
It is notmal hat clients does not see each other if both in AP mode.
client/AP mode is set by wl ap 0/1
lan bridging is controlled by
Quote:
wl wet
NVRAM variables are there for firmware and not for drivers itself. Which firmware uses which NVRAM variable is up to the firmware although many use common Broadcom sourcecode.
X-wrt uses iwconfig instead of wl.
Do you turn off mobile phone when not using it and why using EZ button for occasional use with laptop whe it can allways be turned on without any notable power saving.
hehe i wasnt concerned with power saving but radiation exposure (24h a day)
thats why i was asking and unfortunately you verified that it isnt indeed turned really off
so it is radiating inside the room (eventhough it is doing that with the very small output of 0mW - whatever that means...actually it makes no sense this setting in advanced
wireless settings - if it was 0dB or 0dBm i could understand it)
as for the mobile phone i dont use one i just turn on one when i am going somewhere that there is no phone so i can be found and reached
As for the wireless problem i dont really undestand what i should do
I tried a scan in wl ap 0 and in wl ap 1
nothing is found (although something exists to be found)
I also tried one in AP mode and one in Client mode (i tried it on both units)
NOTHING is found...only wireless cards find them when they are in AP mode
anybody knows :
im trying to run a .php page on php-thttpd and i it doesnt display
all i get is
<?xml version="1.0"?>Direct Access to this location is not allowed.
in /var/log/messages
10.0.0.100 - - [14/Mar/2007:19:52:41 +0000] "GET /index.php HTTP/1.1" 200 138 "" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1; SV1; .NET CLR 2.0.50727; .NET CLR 1.1.4322)
theres nothing there...i copied your thttpd.conf from the optware installation guide
thttpd is working fine with transmission (even php-thttpd that i replaced it with)
it just cannot display the joomla template i downloaded to set up a small web page too
its on www.joomla.org
its gives the error i wrote when you try to view index.php
I was running php-thttpd lon time ago without a problem. But PHP speed was not what one would expect. Expecially I do not recommend it for large interpreting like yoomla. I thik that such king of php is not suited for low end servers like gP. I recommend you to use nanoblogger which precompiles all pages from given template. Instead of running PHP use CGI programming.
it happened after i made a restore of the jffs partition i had kept
please HELP i cannot manually reinstall anything its impossible
now transmission daemon is not running and no logs
Jun 4 22:10:14 (none) user.info : transmissiond: can't load library 'libpthread.so.0'
Jun 4 22:10:14 (none) user.info : : transmissiond: can't load library 'libpthread.so.0'
Jun 4 22:10:14 (none) user.warn transmission_watchdog: Transmission daemon restarted!
Jun 4 22:23:36 (none) user.warn transmission_watchdog: Transmission daemon restarted!
Jun 4 22:40:47 GP user.warn transmission_watchdog: Transmission daemon restarted!
the library IS present (i removed and reinstalled it to be sure)
UPDATE i copied from /jffs/lib the lib to /opt/lib but now i have there 2 versions libpthread 0.27 and 0.28 who knows why
i dont care it works again
OK
forget it