hello,
and thank you everyone for your job.
I have a question. My model is WA830REv2 and I installed the DD-WRT v3.0-r27506. I have this version and I've seen the new build 28211 and KrypteX says: "If the attached build works for you, it can be further updated with any newer-than-28211 webflash build for TL-WA901ND v3.". Does it mean that I could install after the last build r29147 (for example)? Is it recommended to stay updated?
hello,
and thank you everyone for your job.
I have a question. My model is WA830REv2 and I installed the DD-WRT v3.0-r27506. I have this version and I've seen the new build 28211 and KrypteX says: "If the attached build works for you, it can be further updated with any newer-than-28211 webflash build for TL-WA901ND v3.". Does it mean that I could install after the last build r29147 (for example)? Is it recommended to stay updated?
Thank you,
+1
Would we benefit from the upgrade with this HW either performance or security? If we do, which is the build we should use to up DD-WRT v3.0-r27506 (07/09/15) std with?
hello,
and thank you everyone for your job.
I have a question. My model is WA830REv2 and I installed the DD-WRT v3.0-r27506. I have this version and I've seen the new build 28211 and KrypteX says: "If the attached build works for you, it can be further updated with any newer-than-28211 webflash build for TL-WA901ND v3.". Does it mean that I could install after the last build r29147 (for example)? Is it recommended to stay updated?
Thank you,
+1
Would we benefit from the upgrade with this HW either performance or security? If we do, which is the build we should use to up DD-WRT v3.0-r27506 (07/09/15) std with?
hello,
and thank you everyone for your job.
I have a question. My model is WA830REv2 and I installed the DD-WRT v3.0-r27506. I have this version and I've seen the new build 28211 and KrypteX says: "If the attached build works for you, it can be further updated with any newer-than-28211 webflash build for TL-WA901ND v3.". Does it mean that I could install after the last build r29147 (for example)? Is it recommended to stay updated?
Thank you,
+1
Would we benefit from the upgrade with this HW either performance or security? If we do, which is the build we should use to up DD-WRT v3.0-r27506 (07/09/15) std with?
hello,
and thank you everyone for your job.
I have a question. My model is WA830REv2 and I installed the DD-WRT v3.0-r27506. I have this version and I've seen the new build 28211 and KrypteX says: "If the attached build works for you, it can be further updated with any newer-than-28211 webflash build for TL-WA901ND v3.". Does it mean that I could install after the last build r29147 (for example)? Is it recommended to stay updated?
Thank you,
+1
Would we benefit from the upgrade with this HW either performance or security? If we do, which is the build we should use to up DD-WRT v3.0-r27506 (07/09/15) std with?
Hello i installed dd-wrt on my wa830re v2 and i faced problems. I follow all the instructions here but in the menu it has no repeater category only ap/bridge etc. Also i follow the link that big.jack post about make the extender but this didn't help. I think my router stuck after apply changes and also i cant connect or find the virtual network that i create to connect. Is something that i do wrong? Also can anyone tell me if i want to go back to tplink official software how i can do it? just install the stock build from tplink site?
Joined: 04 Nov 2012 Posts: 525 Location: Acapulco, Mexico
Posted: Mon Mar 28, 2016 22:45 Post subject:
its right there, ist call Client Bridge Router you are Tp-Link, they use Atheros Chip not Broadcom
change ip to your DD-WRT to same subnet as the router you want to repeat
6. Open the Wireless -> Basic Settings tab
Physical Interface Section
Wireless Mode : Client Bridge (routed)
Default Gateway Mode : Manual
Gateway : Point to Gateway for network, usually IP of primary router
Wireless Network Mode : Must Match Primary Router
Wireless Network Name(SSID) : Must Match Primary Router exactly including exact case- Make sure you spell this correctly
Wireless Channel : Must Match Primary Router (This will disappear once you put it in RB mode, and isn't needed)
Wireless SSID Broadcast : Enable
Network Configuration : Bridged
Save
Virtual Interfaces Section
Add
Wireless Network Name(SSID) : Same as the primary router (v24SP2 I have not had any problems with signal dropping)
[NOTE] - You CAN try using the same SSID but it usually will not work properly. Many have had random disconnects and/or no connection if the SSID's are the same.
Wireless SSID Broadcast : Enable
Save
DONT make the mistake of loading a firmware from Tplink or you will brick your 830
_________________
TP-Link: TL-WR741ND V4 _________________ TP-Link: TL-WR741ND V4
TP-Link: TL-WR842ND V2
thanks very much danymarc. The point is that i want to connect to wifi that is not mine. In gateway how i can learn the ip of the primary router that i want to connect? Also the password of the wireles network where i put it in. Thanks very much for helping me. Another problem i had is that i want to connect to a wifi that is open without password. The thing is that it has inside a login web page. I have the passwords for login page but i cannt make the extender to repeat that wireless network. (it doesn't transfer me to login page. Just tell me that i have no internet). Is something about settings i must do to work this? in google search i read that i must do a virtual mac adress? Anybody knows about it?
Joined: 04 Nov 2012 Posts: 525 Location: Acapulco, Mexico
Posted: Tue Mar 29, 2016 16:07 Post subject:
More than a year ago I remember reading a post about DD-WRT and Captive Portal or Login Page and this forumer did it, I never saved that Topic, was a interesting one, someone else will have to jump to help on this one
In Status Tab/Wireless at the bottom there is Survey tab click, wait and you will see the SSID you wa my to join, click join and Save & Apply
To learn the ip from primary router, I assume you are connected via smartphone, Tablet or Laptop, the info is right there, in any device
You input password in Wireless/Wireless Security, but is not your case you posted is a open network with Login page _________________ TP-Link: TL-WR741ND V4
TP-Link: TL-WR842ND V2
I did it from the stock webinterface. It said flashed successfully, then it rebooted. Now the left to LEDs are on but nothing happens. What went wrong ?