[g7fya]

Hello dd-wrt.com forum,

I have Trendnet TEW-818DRU Router, and I am trying to make the router act
as an Access Point. I did flash DD-WRT v3.0-r44715 hoping this will help
with what I am trying to do.

I want all the clients (wifi or lan) connecting to TEW-18DRU Router to get
there ip from the main server and the router act as Access Point. I try
setup Network Address Server Settings to 'DHCP Forwarder' but it dose not
seem to be helping. Also I went through the DD-WRT control panel but it
dose not seem I am going anywhere.

here is what i am trying to do:

Main Server
----------------------
dhcp, gateway and dns
ip: 10.0.1.1
----------------------
|
|
v
Router
--------------------------------
Name : tew-818dru
Firmware : DD-WRT v3.0-r44715
Wan - DHCP: 10.0.1.52
--------------------------------
|
|
|
v
| wifi client 1 (DHCP ip: 10.0.1.xxx) | wifi client 2 (DHCP ip: 10.0.1.xxx) | wifi client 3 (DHCP ip: 10.0.1.xxx) |



is this something DD-WRT Firmware can help with ?


here are the current Configuration:

WAN
------------------------------------------------------------------------
Connection Type: Automatic Configuration - DHCP
IPv4 Address : 10.0.1.52
Subnet Mask : 255.255.255.0
Gateway : 10.0.1.1
IPv4 DNS 0 : 10.0.1.1
IPv4 DNS 1 : 10.0.1.4

Local Network
------------------------------------------------------------------------
IP Address :192.168.1.1
Subnet Mask: 255.255.255.0
Gateway : 0.0.0.0
Local DNS :0.0.0.0

Interfaces:
------------------------------------------------------------------------
2: teql0: <NOARP> mtu 1500 qdisc noop state DOWN qlen 100
link/void
3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc sfq state UNKNOWN qlen 1000
link/ether d8:eb:97:ef:e6:96 brd ff:ff:ff:ff:ff:ff
4: vlan1@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue master br0 state UP qlen 1000
link/ether d8:eb:97:ef:e6:96 brd ff:ff:ff:ff:ff:ff
5: vlan2@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP qlen 1000
link/ether d8:eb:97:ef:e6:97 brd ff:ff:ff:ff:ff:ff
inet 10.0.1.52/24 brd 10.0.1.255 scope global vlan2
valid_lft forever preferred_lft forever
6: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc sfq master br0 state UNKNOWN qlen 1000
link/ether d8:eb:97:ef:e6:98 brd ff:ff:ff:ff:ff:ff
7: eth2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc sfq master br0 state UNKNOWN qlen 1000
link/ether d8:eb:97:ef:e6:ab brd ff:ff:ff:ff:ff:ff
8: br0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP qlen 1000
link/ether d8:eb:97:ef:e6:98 brd ff:ff:ff:ff:ff:ff
inet 10.0.2.1/24 brd 10.0.2.255 scope global br0
valid_lft forever preferred_lft forever

any help would be greatly appreciated.
thank you

[kernel-panic69]

You don't use dhcp forwarder.

https://wiki.dd-wrt.com/wiki/index.php/Wireless_access_point

[g7fya]

Dear kernel-panic69 thank you