WNDR3400v2 CFE dump and info

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware
Author Message
Chehri
DD-WRT Novice


Joined: 29 Jul 2012
Posts: 1

PostPosted: Sun Jul 29, 2012 9:09    Post subject: WNDR3400v2 CFE dump and info Reply with quote
I'd love to see DD-WRT on this device, so I decided to dump the CFE and some other information. Let me know if you need anything else and I'll grab it.

Code:
# cat /proc/cpuinfo
system type             : Broadcom BCM5357 chip rev 1
processor               : 0
cpu model               : MIPS 74K V4.9
BogoMIPS                : 264.60
wait instruction        : no
microsecond timers      : yes
tlb_entries             : 64
extra interrupt vector  : no
hardware watchpoint     : yes
ASEs implemented        : mips16 dsp
VCED exceptions         : not available
VCEI exceptions         : not available

unaligned_instructions  : 346
dcache hits             : 2147483648
dcache misses           : 3841948031
icache hits             : 2147483648
icache misses           : 3337240985
instructions            : 2147483648
# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00040000 00010000 "boot"
mtd1: 00700000 00010000 "linux"
mtd2: 005c7abc 00010000 "rootfs"
mtd3: 00010000 00010000 "ML1"
mtd4: 00010000 00010000 "ML2"
mtd5: 00010000 00010000 "ML3"
mtd6: 00010000 00010000 "ML4"
mtd7: 00010000 00010000 "ML5"
mtd8: 00010000 00010000 "ML6"
mtd9: 00010000 00010000 "ML7"
mtd10: 00010000 00010000 "T_Meter1"
mtd11: 00010000 00010000 "T_Meter2"
mtd12: 00010000 00010000 "POT"
mtd13: 00010000 00010000 "board_data"
mtd14: 00010000 00010000 "nvram"
# cat /proc/kmsg
<5>Linux version 2.6.22 (cliffwang@cliffwang-desktop) (gcc version 4.2.3) #47 Fri Aug 26 18:14:59 CST 2011
<4>CPU revision is: 00019749
<4>Found a 8MB ST compatible serial flash
<4>wombo_reset set to gpio 25
<4>Determined physical RAM map:
<4> memory: 03fff000 @ 00000000 (usable)
<7>On node 0 totalpages: 16383
<7>  Normal zone: 127 pages used for memmap
<7>  Normal zone: 0 pages reserved
<7>  Normal zone: 16256 pages, LIFO batch:3
<4>Built 1 zonelists.  Total pages: 16256
<5>Kernel command line: root=/dev/mtdblock2 console=ttyS0,115200 init=/sbin/preinit
<4>Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
<4>Primary data cache 32kB, 4-way, linesize 32 bytes.
<6>Synthesized TLB refill handler (20 instructions).
<6>Synthesized TLB load handler fastpath (32 instructions).
<6>Synthesized TLB store handler fastpath (32 instructions).
<6>Synthesized TLB modify handler fastpath (31 instructions).
<4>PID hash table entries: 256 (order: 8, 1024 bytes)
<4>CPU: BCM5357 rev 1 at 530 MHz
<4>Using 265.000 MHz high precision timer.
<4>Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
<4>Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
<6>Memory: 61168k/65532k available (2779k kernel code, 4300k reserved, 556k data, 184k init, 0k highmem)
<7>Calibrating delay loop... 264.60 BogoMIPS (lpj=1323008)
<4>Mount-cache hash table entries: 512
<6>NET: Registered protocol family 16
<5>SCSI subsystem initialized
<6>usbcore: registered new interface driver usbfs
<6>usbcore: registered new interface driver hub
<6>usbcore: registered new device driver usb
<4>PCI: no core
<4>PCI: Fixing up bus 0
<6>Time: MIPS clocksource has been installed.
<6>NET: Registered protocol family 2
<4>IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
<4>TCP established hash table entries: 2048 (order: 2, 16384 bytes)
<4>TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
<6>TCP: Hash tables configured (established 2048 bind 2048)
<6>TCP reno registered
<6>squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
<4>fuse init (API version 7.8)
<6>io scheduler noop registered (default)
<6>Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled
<6>serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A
<6>loop: module loaded
<6>PPP generic driver version 2.4.2
<6>NET: Registered protocol family 24
<6>PPPoL2TP kernel driver, V0.17
<5>sflash: squash filesystem with lzma found at block 1505
<5>Creating 15 MTD partitions on "sflash":
<5>0x00000000-0x00040000 : "boot"
<5>0x00040000-0x00740000 : "linux"
<5>0x00178544-0x00740000 : "rootfs"
<5>0x00740000-0x00750000 : "ML1"
<5>0x00750000-0x00760000 : "ML2"
<5>0x00760000-0x00770000 : "ML3"
<5>0x00770000-0x00780000 : "ML4"
<5>0x00780000-0x00790000 : "ML5"
<5>0x00790000-0x007a0000 : "ML6"
<5>0x007a0000-0x007b0000 : "ML7"
<5>0x007b0000-0x007c0000 : "T_Meter1"
<5>0x007c0000-0x007d0000 : "T_Meter2"
<5>0x007d0000-0x007e0000 : "POT"
<5>0x007e0000-0x007f0000 : "board_data"
<5>0x007f0000-0x00800000 : "nvram"
<7>PCI: Setting latency timer of device 0000:00:04.1 to 64
<6>ehci_hcd 0000:00:04.1: EHCI Host Controller
<6>ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
<6>ehci_hcd 0000:00:04.1: EHCI Fastpath: New EHCI driver starting
<6>ehci_hcd 0000:00:04.1: irq 5, io mem 0x18004000
<6>ehci_hcd 0000:00:04.1: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
<6>usb usb1: configuration #1 chosen from 1 choice
<6>hub 1-0:1.0: USB hub found
<6>hub 1-0:1.0: 2 ports detected
<7>ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
<7>PCI: Setting latency timer of device 0000:00:04.0 to 64
<6>ohci_hcd 0000:00:04.0: OHCI Host Controller
<6>ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2
<6>ohci_hcd 0000:00:04.0: irq 5, io mem 0x18009000
<6>usb usb2: configuration #1 chosen from 1 choice
<6>hub 2-0:1.0: USB hub found
<6>hub 2-0:1.0: 2 ports detected
<6>Initializing USB Mass Storage driver...
<6>usb 1-2: new high speed USB device using ehci_hcd and address 2
<6>usb 1-2: configuration #1 chosen from 1 choice
<6>usbcore: registered new interface driver usb-storage
<6>USB Mass Storage support registered.
<4>u32 classifier
<6>TCP cubic registered
<6>NET: Registered protocol family 1
<6>NET: Registered protocol family 10
<6>6WIND/LSIIT IPv6 multicast forwarding 0.1 plus PIM-SM/SSM with *BSD API
<6>lo: Disabled Privacy Extensions
<6>IPv6 over IPv4 tunneling driver
<6>sit0: Disabled Privacy Extensions
<6>NET: Registered protocol family 17
<6>802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
<6>All bugs added by David S. Miller <davem@redhat.com>
<4>VFS: Mounted root (squashfs filesystem) readonly.
<6>Freeing unused kernel memory: 184k freed
<4>Warning: unable to open an initial console.
<4>Failed to execute /init
<4>emf: module license 'Proprietary' taints kernel.
<4>Algorithmics/MIPS FPU Emulator v1.5
<0>Initialise conn table 2048 entries
<4>et_module_init: passivemode set to 0x1
<7>PCI: Setting latency timer of device 0000:00:02.0 to 64
<4>eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.60.127 @VERSION_TYPE@
<4>wl_module_init: wl_txq_thresh set to 0x200
<7>PCI: Setting latency timer of device 0000:00:01.0 to 64
<4>eth1: Broadcom BCM4329 802.11 Wireless Controller 5.60.127.2706 @VERSION_TYPE@
<4>Symbol usb_register_driver is being used by a non-GPL module, which will not be allowed in the future
<4>Please see the file Documentation/feature-removal-schedule.txt in the kernel source tree for more details.
<4>Symbol usb_deregister is being used by a non-GPL module, which will not be allowed in the future
<4>Please see the file Documentation/feature-removal-schedule.txt in the kernel source tree for more details.
<4>wl_module_init: rpcq_rxthresh set to 0x200
<4>wl_module_init: wl_txq_thresh set to 0x200
<4>EHCI Fastpath: usb_dev 83f61000
<4>EHCI Fastpath: bus 83e52c00
<4>EHCI Fastpath: Hub 83f61c00
<6>ehci_hcd 0000:00:04.1: EHCI Fastpath: Got the bypass device command in EHCI 83f61000
<4>EHCI Fastpath: usb_dev 83f61000
<4>EHCI Fastpath: bus 83e52c00
<4>EHCI Fastpath: Hub 83f61c00
<6>ehci_hcd 0000:00:04.1: EHCI Fastpath: Got the bypass callback command in EHCI c012969c
<4>EHCI Fastpath: usb_dev 83f61000
<4>EHCI Fastpath: bus 83e52c00
<4>EHCI Fastpath: Hub 83f61c00
<6>ehci_hcd 0000:00:04.1: EHCI Fastpath: Got the RH bypass command in EHCI for EP #0 0004
<6>ehci_hcd 0000:00:04.1: EHCI Fastpath: EP 83e781ec QH a3f3a100 dummy a3f3b060
<4>EHCI Fastpath: usb_dev 83f61000
<4>EHCI Fastpath: bus 83e52c00
<4>EHCI Fastpath: Hub 83f61c00
<6>ehci_hcd 0000:00:04.1: EHCI Fastpath: Got the RH bypass command in EHCI for EP #1 0012
<6>ehci_hcd 0000:00:04.1: EHCI Fastpath: EP 83e781a4 QH a3f3a180 dummy a3f3b120
<4>EHCI Fastpath: EP in 18 EP in2 19 EP out 4
<3>ehci_hcd 0000:00:04.1: dma_pool_free usbnet_qtd, a3f3b060/3f3b060 (bad dma)
<4>bcm_rpc_up: waiting to be connected
<4>bcm_rpc_buf_recv_mgn_high: Recvd:2 Version: 0x53c7fa9
<4>State: 1 Session:0
<4>bcm_rpc_buf_recv_mgn_high: Reason: 0 Dongle Version: 0x53c7fa9
<4>bcm_rpc_buf_recv_mgn_high: Connected!
<4>eth2: Broadcom BCMa8e4 802.11 Wireless Controller 5.60.127.2706 @VERSION_TYPE@
<6>usbcore: registered new interface driver dbus_usbdev
<7>vlan1: add 33:33:00:00:00:01 mcast address to master interface
<7>vlan1: add 01:00:5e:00:00:01 mcast address to master interface
<7>vlan1: add 33:33:ff:7c:2b:68 mcast address to master interface
<6>vlan1: dev_set_allmulti(master, 1)
<6>vlan1: dev_set_promiscuity(master, 1)
<6>device eth0 entered promiscuous mode
<6>device vlan1 entered promiscuous mode
<6>device eth1 entered promiscuous mode
<6>device eth2 entered promiscuous mode
<6>br0: port 3(eth2) entering learning state
<6>br0: port 2(eth1) entering learning state
<6>br0: port 1(vlan1) entering learning state
<6>br0: topology change detected, propagating
<6>br0: port 3(eth2) entering forwarding state
<6>br0: topology change detected, propagating
<6>br0: port 2(eth1) entering forwarding state
<6>br0: topology change detected, propagating
<6>br0: port 1(vlan1) entering forwarding state
<0>IOCTL_AG_REGION_SET: English
<4>vlan2: Setting MAC address to  a0 21 b7 7c 2b 69.
<7>vlan2: add 33:33:00:00:00:01 mcast address to master interface
<7>vlan2: add 01:00:5e:00:00:01 mcast address to master interface
<7>vlan2: add 33:33:ff:7c:2b:69 mcast address to master interface
<6>vlan2: dev_set_promiscuity(master, 1)
<6>device vlan2 entered promiscuous mode
<6>vlan2: dev_set_allmulti(master, 1)
<7>eth1: no IPv6 routers present
<7>eth2: no IPv6 routers present



WNDR3400v2_CFE.zip
 Description:

Download
 Filename:  WNDR3400v2_CFE.zip
 Filesize:  156.41 KB
 Downloaded:  358 Time(s)

Sponsor
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum