Posted: Tue Aug 14, 2012 1:51 Post subject: WHR-HP-G300N
I have upgraded WHR-HP-G300N to 19519
Channel: unknown - Uses Site Survey, displayed channel 31 (have no idea!!!)
Sometimes, i was disconnected from wifi. AP, NG mixed
This build is not working properly. be careful!
Can anyone please share some pointers so I could have the latest build working on my router?
wzr_hp_g300nh wrote:
I still have the same problem. I reset NVRAM before & after the upgrade via telnet and also cleared my browser cache. If I switch my laptop from wired to wireless then I can access other resource, however on cable I can't. Also, I have a cable going from my WZR-HP-G300NH to a switch and the devices on it seem to work fine. It's just the wired devices connected directly to the WZR-HP-G300NH.
Any other suggestions?
Thanks!
buddee wrote:
wzr_hp_g300nh wrote:
Hi,
I have been using build # 18024 and recently tried upgrading to recent builds but I
keep getting the connectivity problems between devices that are connected directly to the router via wire. I tried resetting the NVRAM via telnet but then upgrade but this didn't help either. Am I missing some magic here
Please help.. thanks!
The only magic i can think of that you are missing is perhaps turning off any firewall software running on the pc you are using to flash with, also - disable any blocking add-ons that your web browser may be using as well, then clear cache and cookies and re-try.
With my parents' TPLink 1043ND, they literally have to unplug the router twice a day, as the wireless dies.
Unfortunately this is now their "Prod" router by default as their WRT54GL seems to have died following a thunderstorm, after years of service.
The problem is also that they have several wireless devices, and require multi-SSID (and SSH for me to do remote troubleshooting if/when needed)
The best part of all this? People report this in forums, and it's ignored. People open trac tickets, and this is the response they get:
http://svn.dd-wrt.com/ticket/2659
With my parents' TPLink 1043ND, they literally have to unplug the router twice a day, as the wireless dies.
Unfortunately this is now their "Prod" router by default as their WRT54GL seems to have died following a thunderstorm, after years of service.
The problem is also that they have several wireless devices, and require multi-SSID (and SSH for me to do remote troubleshooting if/when needed)
The best part of all this? People report this in forums, and it's ignored. People open trac tickets, and this is the response they get:
http://svn.dd-wrt.com/ticket/2659
They aren't always read right off. Sometimes you just have to bump and hope someone who knows what their doing see's it.
I understand your frustration, but try to remember this work is done for free.
Posted: Thu Aug 16, 2012 17:26 Post subject: DLink DIR-615 i1 No MilkFish
I just installed dir615i1-factory-to-ddwrt-firmware.bin and then updated to dir615i1-firmware.bin. When I went to the Services Tab, I noticed that the MilkFish SIP Service Tab was not there. Am I missing something or do I need to install the MF bin separately? This is the main reason I installed DD-WRT was for the MilkFish Sip Service.
I have tried with build r14896 and r19342 in two different WRT160NLs and still the same problem. Anything I can do to help solve it? Should I provide more information?
Router Webinterface (192.168.1.1) -> Services -> Services -> SES / AOSS / EZ-SETUP / WPS Button -> Turning off radio -> Enable
Does not work.
Make it work with workaround here: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=160654
Pressing the button seems to do something to the QSS-LED. QSS-LED turnes off but then turns on after 1-2 seconds. WiFi stays on.
Turn radio off at boot -> Enable does not work either. Maybe there is a connection between those two options?
QSS Button on this router is gpio number 12.
"1" when not pressed
"0" when pressed
Last edited by daheist on Sun Aug 19, 2012 20:46; edited 1 time in total
Some issues notice with this firmware 19519 on my Buffalo QZR-HP-AG300H :
Noticed messages like this while being connected on the ssh console to the router (which I don't know what they mean):
Code:
channel 3: open failed: connect failed:
channel 26: open failed: connect failed:
channel 27: open failed: connect failed:
channel 33: open failed: connect failed:
channel 39: open failed: connect failed:
channel 23: open failed: connect failed:
channel 30: open failed: connect failed:
channel 16: open failed: connect failed:
And one more thing noticed with the 19519 firmware, on the Wifi Status - is unable to show the Channel and ACK time _________________ Buffalo WZR-HP-AG300H