I have a problem with BWMon. Somehow, the total download and upload get reset. I didn't exactly see the data were set to zero. But the amount was in GB yesterday could be in hundreds of MB in the next morning. Is it a bug or I didn't interpret the meaning corretly? Also the download/upload rate jump a lot, sometimes they are way above the line rate. Any idea?
I had it once that counters were reset without any indication.
This shouldn't happen but I couldn't replicate the failure.
Is there a difference between live and total traffic?
About the up/down load I noticed it too but only from time to time.
I did not write the script for the data collection.
Currently working on conntrack which need my attention.
Will look into it when it's finished.
shimh wrote:
I have a problem with BWMon. Somehow, the total download and upload get reset. I didn't exactly see the data were set to zero. But the amount was in GB yesterday could be in hundreds of MB in the next morning. Is it a bug or I didn't interpret the meaning corretly? Also the download/upload rate jump a lot, sometimes they are way above the line rate. Any idea?
Joined: 06 Feb 2010 Posts: 7401 Location: Little Rock
Posted: Fri Jun 29, 2012 4:01 Post subject:
Here is what i get just now when i try. Same router, WL-520gu and 19342 usb generic. Not sure why this is though. I've run optware the right on this unit in the past.
Joined: 06 Feb 2010 Posts: 7401 Location: Little Rock
Posted: Fri Jun 29, 2012 11:30 Post subject:
The first tests i did was using a 2gig USB thumb drive, i did this last test with a USB 150gig hard drive, both devices have no problems working on my computers, and both drives pass an integrity disk test, so i'm not sure about that. I will however run the test again with logging and report back. _________________ Wireless N Config | Linking Routers | DD-WRT Wiki | DD-WRT Builds | Peacock - Broadcom FAQ
Joined: 06 Feb 2010 Posts: 7401 Location: Little Rock
Posted: Fri Jun 29, 2012 14:49 Post subject:
Re-tried using same build and different drive, it gets stuck right after this now.
Connecting to ipkg.nslu2-linux.org (140.211.169.161:80)
coreutils_8.4-1_mips 100% |*********************************************************************************************| 2728k 0:00:00 ETA
And it sat there for over 20 mins, after which it auto closed my login to the terminal, so needless to say, there is no log in /tmp to look at. But i'm going to continue to test throughout the day, so i will report back with hopefully good results. _________________ Wireless N Config | Linking Routers | DD-WRT Wiki | DD-WRT Builds | Peacock - Broadcom FAQ
I did a fresh install on my E3200. running 19342 K26 mega
I took multiple runs before install was successful.
Have the feeling its also a time-out problem with nslu2 source.
I also saw a pending download state and then it failed.
I also checked my server logs for errors and there are none.
After the last file you retrieved from my server the next step would installation of busybox
Joined: 06 Feb 2010 Posts: 7401 Location: Little Rock
Posted: Sat Jun 30, 2012 0:22 Post subject:
basmaf wrote:
My current install on the 3200 seems to be working fine.
Tomorrow i will continue testing.
I will probably receive a WRT610v1 tomorrow which allows me to test K24 kernel
Which I should mention is a donation by PetervdM
Many thanks
Most excellent and will probably be alot better to test on than this wl520gu.
But i did re-run install, and it went clean, i rebooted the unit, and optware appears to be installed, only one problem i see now, no more mypage installed.
Joined: 06 Feb 2010 Posts: 7401 Location: Little Rock
Posted: Sat Jun 30, 2012 0:45 Post subject:
Perhaps so, but i do not see it on the webgui status and its not in the optware install partition, i just searched thru that with scp and couldn't find it. I will re-run the script and try this once more. _________________ Wireless N Config | Linking Routers | DD-WRT Wiki | DD-WRT Builds | Peacock - Broadcom FAQ