OTRW2 (incl. Mypage)

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware
Goto page Previous  1, 2, 3, ... 62, 63, 64  Next
Author Message
basmaf
DD-WRT Guru


Joined: 24 Feb 2011
Posts: 1074

PostPosted: Thu Jun 21, 2012 18:30    Post subject: Reply with quote
Did you find the problem?
Sponsor
buddee
DD-WRT Guru


Joined: 06 Feb 2010
Posts: 7401
Location: Little Rock

PostPosted: Thu Jun 21, 2012 19:13    Post subject: Reply with quote
Hadn't had time to look yet, was going to last night, but had to do some other things. Will test ASAP though, as i am interested to find out what the problem seems to be.
_________________
Wireless N Config | Linking Routers | DD-WRT Wiki | DD-WRT Builds | Peacock - Broadcom FAQ

Having problems with port forwarding? Check out Port Forward Troubleshooting for more info.
buddee
DD-WRT Guru


Joined: 06 Feb 2010
Posts: 7401
Location: Little Rock

PostPosted: Fri Jun 22, 2012 0:55    Post subject: Reply with quote
Ok, did the script on NEWD 15943, as i noted in the previous post - everything ran as it should on the install script, no errors, but after rebooting - mypage wasn't loading in the status...

So i decided to upgrade my build to 19342 NEWD usb generic, turned on USB in services and waalaa, loaded right up without having to re-run the install script. So honestly, i'm not exactly sure what the problem is, but i am more convinced that it would appear to be build related.

18024 = no good for this
15943 = no good for this

14929 and 19342 both work fine with it right from the reboot.

And did i mention, big thanks for your work on this, its most excellent! Cool



optware-newd_19342.jpg
 Description:
19342 loaded it with no problem
 Filesize:  54.22 KB
 Viewed:  23263 Time(s)

optware-newd_19342.jpg



_________________
Wireless N Config | Linking Routers | DD-WRT Wiki | DD-WRT Builds | Peacock - Broadcom FAQ

Having problems with port forwarding? Check out Port Forward Troubleshooting for more info.
buddee
DD-WRT Guru


Joined: 06 Feb 2010
Posts: 7401
Location: Little Rock

PostPosted: Fri Jun 22, 2012 1:19    Post subject: Reply with quote
Seems though now, i have stumbled upon another problem, i tried to reboot from the webgui, noticed the LED on my unit never flickered, so i open a browser and sure enough, it never rebooted.

I then rebooted it by unplug the power and re-plug, then SSH'd into the shell and disabled a few services then issued a 'reboot' and this is what i am seeing with it. Essentially though, i can't reboot unless i unplug the power to the unit. It'll just sit there not performing the reboot that it should.



optware-test2.jpg
 Description:
 Filesize:  153.06 KB
 Viewed:  23283 Time(s)

optware-test2.jpg



_________________
Wireless N Config | Linking Routers | DD-WRT Wiki | DD-WRT Builds | Peacock - Broadcom FAQ

Having problems with port forwarding? Check out Port Forward Troubleshooting for more info.
basmaf
DD-WRT Guru


Joined: 24 Feb 2011
Posts: 1074

PostPosted: Fri Jun 22, 2012 6:06    Post subject: Reply with quote
Please check if /opt/etc/init.d/S08reboot exists.
I think shutdown scripts are ran 2 times.

could post output of:
date -r /bin/busybox +%Y
date -r /bin/busybox +%m

Please run the prep script again to be sure all is set correctly.
buddee
DD-WRT Guru


Joined: 06 Feb 2010
Posts: 7401
Location: Little Rock

PostPosted: Fri Jun 22, 2012 19:51    Post subject: Reply with quote
I formatted the drive last night and re-running the install now, will report back when it finishes up.
_________________
Wireless N Config | Linking Routers | DD-WRT Wiki | DD-WRT Builds | Peacock - Broadcom FAQ

Having problems with port forwarding? Check out Port Forward Troubleshooting for more info.
wabe
DD-WRT Guru


Joined: 17 Jun 2006
Posts: 751

PostPosted: Fri Jun 22, 2012 21:52    Post subject: Reply with quote
Noticed that virtual hosting doesn't work any longer from the wan side and after looking into the issue it seems that there is a problem with 'pound'.
Getting the following error message when pound starts:

/usr/sbin/wl:-i eth2 interference 3 ->wl driver adapter not found

Have no idea what this means but the virtual host cannot be reached
basmaf
DD-WRT Guru


Joined: 24 Feb 2011
Posts: 1074

PostPosted: Fri Jun 22, 2012 22:05    Post subject: Reply with quote
Do you use vlighttpd?
I run pound and vlighttpd without problems.
http requests on otrw.basmaf are forwarded to vlighttpd

wabe wrote:
Noticed that virtual hosting doesn't work any longer from the wan side and after looking into the issue it seems that there is a problem with 'pound'.
Getting the following error message when pound starts:

/usr/sbin/wl:-i eth2 interference 3 ->wl driver adapter not found

Have no idea what this means but the virtual host cannot be reached
buddee
DD-WRT Guru


Joined: 06 Feb 2010
Posts: 7401
Location: Little Rock

PostPosted: Fri Jun 22, 2012 23:34    Post subject: Reply with quote
This is what is going on so far..

Why i formatted the drive last night and start over today is because last night, after posting the last pic, i could never get back in via SSH, and its doing it again now, and since i can't get into the shell, i really don't know (and won't be able to trace) what the problem is. I can get in via the webgui, but that doesn't do me much good to try to debug anything. When i do try to login via SSH (or telnet, doesn't matter) it just sits there, and does nothing, after issue the password.



optware-test3.jpg
 Description:
 Filesize:  25.29 KB
 Viewed:  23195 Time(s)

optware-test3.jpg



_________________
Wireless N Config | Linking Routers | DD-WRT Wiki | DD-WRT Builds | Peacock - Broadcom FAQ

Having problems with port forwarding? Check out Port Forward Troubleshooting for more info.
buddee
DD-WRT Guru


Joined: 06 Feb 2010
Posts: 7401
Location: Little Rock

PostPosted: Sat Jun 23, 2012 1:23    Post subject: Reply with quote
Ok, after i let it sit for an hr, it finally let me SSH into the shell, here is the output for what you requested, doesn't look like the reboot script exist. However, this time, after issue the commands, i issued a 'reboot' and it rebooted clean this time, and reboots clean from webgui as well. Everything seems running normal again since i re-ran the script - except for the massive delay in being able to SSH into the router.

I am having a feeling that the delay in being able to login via SSH has to do with the architecture i am dealing with, this wl520gu can't handle running this, because if i use my E3000, RT-N16 or WNR3500L, i have no problems with this and it seems everything executes much faster (of course, better hardware), with the 520gu, it takes much time for you to be able to do anything on it.

But unfortunate thing is its the only older unit i have that can run NEWD builds with a USB to test this on. i have a 500gpv2 as well, but its specs are pretty much the same as the 520gu minus it has bigger flash and more ram, otherwise same.



optware-test4.jpg
 Description:
 Filesize:  47.95 KB
 Viewed:  23181 Time(s)

optware-test4.jpg



_________________
Wireless N Config | Linking Routers | DD-WRT Wiki | DD-WRT Builds | Peacock - Broadcom FAQ

Having problems with port forwarding? Check out Port Forward Troubleshooting for more info.
buddee
DD-WRT Guru


Joined: 06 Feb 2010
Posts: 7401
Location: Little Rock

PostPosted: Sat Jun 23, 2012 1:47    Post subject: Reply with quote
And now i am banging my head on the keyboard, after the reboot, its not mounting the disk properly again!

It is once again choosing to mount part3 instead of part1 like it should, thus optware isn't working anymore. And this is with 19342 newd usb generic.



optware-test5.jpg
 Description:
 Filesize:  67.63 KB
 Viewed:  23178 Time(s)

optware-test5.jpg



_________________
Wireless N Config | Linking Routers | DD-WRT Wiki | DD-WRT Builds | Peacock - Broadcom FAQ

Having problems with port forwarding? Check out Port Forward Troubleshooting for more info.
basmaf
DD-WRT Guru


Joined: 24 Feb 2011
Posts: 1074

PostPosted: Sat Jun 23, 2012 7:43    Post subject: Reply with quote
Confused
Can you sent me the syslog from current state.
Need to dig into the logs to check where it goes wrong.

I don't understand why all is working fine on 14929
and not on 19432.
I'd wish I had such unit to test.

For troubleshooting can you do a manual mount and disable automount
Are you using automount via GUI?

@ BW how is your TM doing?
Any issues? and on which build are you?
basmaf
DD-WRT Guru


Joined: 24 Feb 2011
Posts: 1074

PostPosted: Sat Jun 23, 2012 8:00    Post subject: Reply with quote
Some other question

I see in the ps output run_rc_startup is still running.
Do you have any additional features in your startup script?
wabe
DD-WRT Guru


Joined: 17 Jun 2006
Posts: 751

PostPosted: Sat Jun 23, 2012 8:31    Post subject: Reply with quote
basmaf wrote:
Do you use vlighttpd?
I run pound and vlighttpd without problems.
http requests on otrw.basmaf are forwarded to vlighttpd

wabe wrote:
Noticed that virtual hosting doesn't work any longer from the wan side and after looking into the issue it seems that there is a problem with 'pound'.
Getting the following error message when pound starts:

/usr/sbin/wl:-i eth2 interference 3 ->wl driver adapter not found

Have no idea what this means but the virtual host cannot be reached


Yes vlighttpd & pound. Have worked flawlessly for quite some time. Can't tell exactly when the issue started might be after a package upgrade.

Can anyone tell what the error message means?
basmaf
DD-WRT Guru


Joined: 24 Feb 2011
Posts: 1074

PostPosted: Sat Jun 23, 2012 8:44    Post subject: Reply with quote
i did a ipkg upgrade yesterday
All packages are the latest available.

give command "wl -i eth2" it will show you the options

interference
Get/Set interference mitigation mode. Choices are:
0 = none
1 = non wlan
2 = wlan manual
3 = wlan automatic
Goto page Previous  1, 2, 3, ... 62, 63, 64  Next Display posts from previous:    Page 2 of 64
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum