New build: DD-WRT v3.0 --- 28493 --- 2015/12/10

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware
Goto page 1, 2, 3, 4  Next
Author Message
KrypteX
DD-WRT Guru


Joined: 18 Jan 2014
Posts: 2411

PostPosted: Thu Dec 10, 2015 13:15    Post subject: New build: DD-WRT v3.0 --- 28493 --- 2015/12/10 Reply with quote
DD-WRT build 28493 - 2015/12/10 has been released: ftp://ftp.dd-wrt.com/betas/2015/12-10-2015-r28493/

Changelog excerpt from http://www.dd-wrt.com/phpBB2/viewtopic.php?t=279467

Your reports for Broadcom units are greatly appreciated !
Router:
Firmware:
Kernel:
Status:
Reset:
Errors:

This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build (e.g. 28493_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. Please also do not respond to such questions. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless. If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build.

If there are issues with the webflash update from previous build 28444, keep in mind that the problem is caused by build 28444, which has a bug in the webflashing code, as described in http://svn.dd-wrt.com/ticket/4988#comment:13

To circumvent this problem, here are a couple of useful methods (please adapt to your particular case):
- WGET method http://www.askmeaboutlinux.com/?p=2819
- TFTP method http://www.dd-wrt.com/wiki/index.php/TFTP_flash

_________________
THERE ARE NO STRANGERS HERE; ONLY FRIENDS YOU HAVEN'T YET MET.
________________________________________________________________________________________________________
DD-WRT CHANGELOG | DEVICES | DD-WRT BUILDS | KONG BUILDS | UNOFFICIAL BUILDS | DD-WRT in VIRTUALBOX

Testing BrainSlayer's DD-WRT build 31924 on various units:
NETGEAR : WNDR3800 WNDR3800CH WNDRMACv2 WNDRMACv1 WNR2200 WNR2000v3
TP-LINK : ArcherC7v3 WR1043NDv3 WR740Nv4 WR740Nv6 WR710Nv1 WR810Nv1 WA850REv1 WA901NDv3 WA901NDv4
D-LINK : DIR-862L DIR-615D2
ASUS : RT-N10 C1
VirtualBox : x86_64


Last edited by KrypteX on Sat Dec 12, 2015 8:16; edited 4 times in total
Sponsor
ghoffman
DD-WRT User


Joined: 03 Jan 2010
Posts: 453

PostPosted: Thu Dec 10, 2015 14:30    Post subject: Reply with quote
Router Model: Linksys EA6400
Firmware Version: DD-WRT v3.0-r28493M std (12/10/15)
Kernel Version: Linux 3.10.94 #5207 SMP Thu Dec 10 06:57:16 CET 2015 armv7l

using as dual-band AP with usb printerserver.

errors: usb device errors persist. usb printer is repeatedly identified, de-identified. see below for tail of dmesg after a few minutes of uptime:


usb 1-1: new high-speed USB device number 77 using ehci-pci
usb 1-1: new high-speed USB device number 78 using ehci-pci
usb 1-1: new high-speed USB device number 79 using ehci-pci
usb 1-1: new high-speed USB device number 80 using ehci-pci
usb 1-1: new high-speed USB device number 81 using ehci-pci
usb 1-1: new high-speed USB device number 82 using ehci-pci
usb 1-1: new high-speed USB device number 83 using ehci-pci
usb 1-1: new high-speed USB device number 84 using ehci-pci
usb 1-1: new high-speed USB device number 85 using ehci-pci
usblp 1-1:1.1: usblp0: USB Bidirectional printer dev 85 if 1 alt 0 proto 2 vid 0x04A9 pid 0x26EF
usb 1-1: USB disconnect, device number 85
usblp0: removed
usb 1-1: new high-speed USB device number 86 using ehci-pci
usblp 1-1:1.1: usblp0: USB Bidirectional printer dev 86 if 1 alt 0 proto 2 vid 0x04A9 pid 0x26EF
usb 1-1: USB disconnect, device number 86
usblp0: removed
usb 1-1: new high-speed USB device number 87 using ehci-pci
jrscs
DD-WRT User


Joined: 09 Aug 2010
Posts: 273

PostPosted: Thu Dec 10, 2015 15:17    Post subject: Reply with quote
Build 28493 previous build 28417

Router: RT-AC87U - primary router/gateway
Firmware Version: DD-WRT v3.0-r28493M std (12/10/15)
Kernel Version: Linux 3.10.94 #5214 SMP Thu Dec 10 07:29:16 CET 2015 armv7l
2.4Ghz (NG-mixed) with 40Mhz channel width: OK
5Ghz (AC/N-Mixed) with 80Mhz channel width: OK
Guest-Vlan 2.4Ghz: OK
SSH: OK
Telnet: OK
Port Forward: OK
WOL over the Internet: OK
VNC Repeater: OK
USB 2.0 storage ext3 mount to JFFS: OK
USB 3.0 storage NTFS mount to MNT: OK
NAS Samba shared drive: NO on reboot, but hitting Apply Settings button in NAS tab will start it
PPTP Server: OK
Wi-viz 2.4Ghz & 5Ghz: 2.4Ghz OK – 5Ghz NO
Reset via GUI: Yes before and after upgrade
Status: Working
Error(s): Guest network does not show any output signal, noise, or SNR in the wireless clients output table

Router: RT-AC68R - primary router/gateway
Firmware Version: DD-WRT v3.0-r28493M std (12/10/15)
Kernel Version: Linux 3.10.94 #5207 SMP Thu Dec 10 06:57:16 CET 2015 armv7l
2.4Ghz (NG-mixed) with 40Mhz channel width: OK
5Ghz (AC/N-Mixed) with 80Mhz channel width: OK
Guest-Vlan 2.4Ghz: OK
SSH: OK
Telnet: OK
Port Forward: OK
WOL over the Internet: OK
VNC Repeater: OK
USB 2.0 storage ext3 mount to JFFS: OK
USB 3.0 storage NTFS mount to MNT: OK
NAS Samba shared drive: OK
PPTP Server: OK
Wi-viz 2.4Ghz & 5Ghz: OK
Reset via GUI: Yes before and after upgrade
Status: Working
Error(s): Guest network does not show any output signal, noise, or SNR in the wireless clients output table

Repeater Bridge Build 28493 previous build 28417

Router: RT-AC66U - Repeater Bridge on 5 Ghz (AC-Only) to RT-AC87U
Firmware Version: DD-WRT v3.0-r28493 giga (12/10/15)
Kernel Version: Linux 3.10.94 #10630 Thu Dec 10 10:36:01 CET 2015 mips
2.4Ghz (NG-mixed) with 20Mhz channel width: OK
5Ghz (AC-Only): OK
Reset via GUI: No
Status: Working
Error(s): OK

*** Builds after 26339 when erasing NVRAM in telnet session or Power UP Reset, resets 5.0 GHz radio to 2.4 GHz radios – To recover return to 26339 ***
*** Builds after 26339 use the Administration >> Factory Defaults tab in the GUI to reset NVRAM ***
*** Since 27343 the following command needs to be included in the Start-up script, ‘sleep 5; startstop lan’ to allow the 5 Ghz to connect to the main AP in Repeater Bride mode when rebooting. Thanks to Magnetron 1.1 for putting in forum topic ***

Router: e4200 – Repeater Bridge on 5 Ghz (N) to RT-AC87U
Firmware Version: DD-WRT v3.0-r28493 mega (12/10/15)
Kernal Version: Linux 3.10.94 #10646 Thu Dec 10 10:49:56 CET 2015 mips
2.4Ghz (NG-mixed) with 20Mhz channel width: OK
5Ghz (N):OK
Reset via GUI: No
Status: Working
Error(s): OK

*** Since 27343 the following command needs to be included in the Start-up script, ‘sleep 5; startstop lan’ to allow the 5 Ghz to connect to the main AP in Repeater Bride mode when rebooting. Thanks to Magnetron 1.1 for putting in forum topic ***

_________________
Netgear R7800 - DD-WRT v3.0-r45767 std (02/17/21)
Asus AC87U A1 - DD-WRT v3.0-r45767 std (02/17/21)
Repeater Bridges(s)
Asus AC68R A1 - DD-WRT v3.0-r45767 std (02/17/21)
Netgear R6400 V2 - DD-WRT v3.0-r45767 std (02/17/21)
Asus AC66U A1 - DD-WRT v3.0-r45767 giga (02/17/21)


Last edited by jrscs on Thu Dec 10, 2015 18:20; edited 2 times in total
onnoossendrijver
DD-WRT Novice


Joined: 30 Oct 2015
Posts: 10

PostPosted: Thu Dec 10, 2015 16:03    Post subject: Reply with quote
I can not upgrade from the previous build using the webflash on my D-Link DIR-880L.
During webflash my connection resets. I have to power the AP down and up to make it work again on the previous version.
azncoduyen
DD-WRT Novice


Joined: 10 Dec 2015
Posts: 1

PostPosted: Thu Dec 10, 2015 16:46    Post subject: Reply with quote
TPLINK Archer C9v1 web update fail. The webpage stop working and remain on this state until a router reboot.

However, logging into ssh and doing write xxxx.bin linux update the router.
lyuan
DD-WRT User


Joined: 05 Apr 2011
Posts: 85

PostPosted: Thu Dec 10, 2015 16:55    Post subject: Reply with quote
Same issue here:

Model: R7000
Current FW: 28444

When I try to upload the file through the web interface, I get a "connection refused" after a few seconds. I have to reboot the device before I can get the web UI stuff to work again.

This might be an issue with 28444, and not the new FW.

L.
Bernadoe
DD-WRT User


Joined: 03 Dec 2014
Posts: 217

PostPosted: Thu Dec 10, 2015 17:40    Post subject: Reply with quote
On WinSCP:
1 Select New Site;
2 File protocol: SCP;
3 Hostname: 192.168.1.1 (or your router IP);
4 Username: root
5 Password: your admin pass
6 Drag downloaded firmware from Download folder and drop in /tmp

On putty;
1 Login on 192.168.1.1 (user root and pass);
2 Type:
cd /tmp (Enter)
mtd -r write xxxxx.bin linux (Enter) (Sure, replace xxxx with your firmware filename...)

Router: Netgear R7000
Firmware: DD-WRT v3.0-r28493M std (12/10/15)
Kernel: Linux 3.10.94 #5207 SMP Thu Dec 10 06:57:16 CET 2015 armv7l
Status: Working
Reset: No
Previous: 28444
Errors: No
denislen
DD-WRT User


Joined: 16 Sep 2015
Posts: 50

PostPosted: Thu Dec 10, 2015 19:00    Post subject: Reply with quote
asus rt-n10U black

all fine
slobodan
DD-WRT Guru


Joined: 03 Nov 2011
Posts: 1552
Location: Zwolle

PostPosted: Thu Dec 10, 2015 19:15    Post subject: Reply with quote
Router: E4200 V1
Firmware: dd-wrt.v24-28493_NEWD-2_K3.x_mega-e4200.bin
Kernel: 3.10.94
Reset: no.
Errors: no.
Note: no USB device attached, does not function as DHCP or DNS server.

_________________
2 times APU2 Opnsense 21.1 with Sensei

2 times RT-AC56U running DD-WRT 45493 (one as Gateway, the other as AP, both bridged with LAN cable)

3 times Asus RT-N16 shelved

E4200 V1 running freshtomato 2020.8 (bridged with LAN cable)

3 times Linksys WRT610N V2 converted to E3000 and 1 original E3000 running freshtomato 2020.8 (bridged with LAN cable)

RalphMalph
DD-WRT Novice


Joined: 29 Dec 2011
Posts: 42

PostPosted: Thu Dec 10, 2015 19:29    Post subject: Update fails Reply with quote
TP-Link Archer C9 v1 28444

Within seconds the website goes to "blank" with the text, connection reinitialised

Bug in 28444 or in the new one???
KrypteX
DD-WRT Guru


Joined: 18 Jan 2014
Posts: 2411

PostPosted: Thu Dec 10, 2015 19:37    Post subject: Re: Update fails Reply with quote
RalphMalph wrote:
Bug in 28444 or in the new one???

Read the part in red: http://www.dd-wrt.com/phpBB2/viewtopic.php?p=996561#996561

_________________
THERE ARE NO STRANGERS HERE; ONLY FRIENDS YOU HAVEN'T YET MET.
________________________________________________________________________________________________________
DD-WRT CHANGELOG | DEVICES | DD-WRT BUILDS | KONG BUILDS | UNOFFICIAL BUILDS | DD-WRT in VIRTUALBOX

Testing BrainSlayer's DD-WRT build 31924 on various units:
NETGEAR : WNDR3800 WNDR3800CH WNDRMACv2 WNDRMACv1 WNR2200 WNR2000v3
TP-LINK : ArcherC7v3 WR1043NDv3 WR740Nv4 WR740Nv6 WR710Nv1 WR810Nv1 WA850REv1 WA901NDv3 WA901NDv4
D-LINK : DIR-862L DIR-615D2
ASUS : RT-N10 C1
VirtualBox : x86_64
RalphMalph
DD-WRT Novice


Joined: 29 Dec 2011
Posts: 42

PostPosted: Thu Dec 10, 2015 19:51    Post subject: Re: Update fails Reply with quote
KrypteX wrote:
RalphMalph wrote:
Bug in 28444 or in the new one???

Read the part in red: http://www.dd-wrt.com/phpBB2/viewtopic.php?p=996561#996561


Thanx, overlooked that part
RalphMalph
DD-WRT Novice


Joined: 29 Dec 2011
Posts: 42

PostPosted: Thu Dec 10, 2015 20:11    Post subject: Re: Update fails Reply with quote
RalphMalph wrote:
KrypteX wrote:
RalphMalph wrote:
Bug in 28444 or in the new one???

Read the part in red: http://www.dd-wrt.com/phpBB2/viewtopic.php?p=996561#996561


Thanx, overlooked that part


wget-method did the job. Luckily.
CTEC
DD-WRT User


Joined: 10 Dec 2015
Posts: 84

PostPosted: Thu Dec 10, 2015 20:40    Post subject: Reply with quote
Router: Belkin F7D3301 / F7D7301 v1
Firmware: DD-WRT v3.0-r28493 mega (12/10/15)
Kernel: Linux 3.10.94 #10646 Thu Dec 10 10:49:56 CET 2015 mips
Status: Works!
Reset: Needed to reflash from K2.6 18946 mini to K3.0 21605 Mega to 28493. Previously was on 28444. Tried wget method, but router failed to load. Console mentioned unreadable image.
Errors: Multiple. Read below.

1. Since 21605, I see the total NVRAM was increased to 64 KB from 32 KB since the K3.X upgrade on 21605. Now with the newer builds from this year, I see NVRAM total is 256 KB. Is this a miscalculation?

2. Resetting the NVRAM will cause DD-WRT to identify the router as WRT54GL, which creates a kernel panic, crashes, and reboot loops. Resetting was not a problem on 21605.

3. Upgrading on any K3.X for F7D7301/F7D3301/F7D7302/F7D3302 will not work. Can only upgrade from the generic Mega build. Why does DD-WRT continue to publish these custom images?
robo77
DD-WRT Novice


Joined: 24 Dec 2013
Posts: 31

PostPosted: Thu Dec 10, 2015 21:25    Post subject: Reply with quote
Router: Linksys EA2700
Firmware: dd-wrt-28493-ea2700.trx
Status: Not Working
Reset: Yes
Errors: Router get on boot loop

Tested 28397,28417,28444 still not work.
Return to last working firmware 27805
Goto page 1, 2, 3, 4  Next Display posts from previous:    Page 1 of 4
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum