Posted: Tue Dec 01, 2015 14:42 Post subject: Re: USB not working
Mr_Orange wrote:
Herby213 wrote:
So is USB working fine for everyone?
Has anyone managed to successfully set up OPEN VPN?
My VPN requires that. I use AES-256-CBC as a cipher encryption, but this option isn't available.
On a WRT1900ACv2 is not working at least for me.
When activating usb config in webif my router bricks.
This happen also without inserting any usb pendrive.
I'm having the same issue with the latest builds when i reboot after enabling USB support my WRT1900ACv2 bricks.
I didn't figure out that it was USB support that was causing the problem until now...
Posted: Tue Dec 01, 2015 17:05 Post subject: Re: USB not working
Giraffe wrote:
Mr_Orange wrote:
On a WRT1900ACv2 is not working at least for me.
When activating usb config in webif my router bricks.
This happen also without inserting any usb pendrive.
I'm having the same issue with the latest builds when i reboot after enabling USB support my WRT1900ACv2 bricks.
Which build version ? "Latest builds" doesn't say anything to me. Give a number. _________________ THERE ARE NO STRANGERS HERE; ONLY FRIENDS YOU HAVEN'T YET MET.
________________________________________________________________________________________________________
DD-WRT CHANGELOG | DEVICES | DD-WRT BUILDS | KONG BUILDS | UNOFFICIAL BUILDS | DD-WRT in VIRTUALBOX
Posted: Tue Dec 01, 2015 17:16 Post subject: Re: USB not working
KrypteX wrote:
Giraffe wrote:
Mr_Orange wrote:
On a WRT1900ACv2 is not working at least for me.
When activating usb config in webif my router bricks.
This happen also without inserting any usb pendrive.
I'm having the same issue with the latest builds when i reboot after enabling USB support my WRT1900ACv2 bricks.
Which build version ? "Latest builds" doesn't say anything to me. Give a number.
Sorry, you're right I should have been more specific.
I'm writing about DD-WRT build 28397, but this also happened to my WRT1900ACv2 with DD-WRT R28374.
I'm currently using R28211 (again) this build is not affected.
Posted: Tue Dec 01, 2015 21:42 Post subject: Re: USB not working
Giraffe wrote:
Mr_Orange wrote:
Herby213 wrote:
So is USB working fine for everyone?
Has anyone managed to successfully set up OPEN VPN?
My VPN requires that. I use AES-256-CBC as a cipher encryption, but this option isn't available.
On a WRT1900ACv2 is not working at least for me.
When activating usb config in webif my router bricks.
This happen also without inserting any usb pendrive.
I'm having the same issue with the latest builds when i reboot after enabling USB support my WRT1900ACv2 bricks.
I didn't figure out that it was USB support that was causing the problem until now...
So I just realized I'm having the same issue. Even if I reload a new build (from today) it wont boot... I have to go back to stock firmware. Has anybody figured out how to get DD-WRT to work again after you've enabled USB?
I was using the brainslayer build from the 28th of Nov. Do not remember the number.
Edit: I loaded the stock firmware then DD-WRT afterwards and I got a clean DD-WRT install.
First post...thanks for the efforts....
I just made the switch from many frustrated months on OpenWRT and i have to say that DD-WRT is working great on my v1. USB file transfers are particularly impressive. Build r28374
I had been on OpenWRT wanting to use IPSEC. I thought that Open/Strong Swan wasnt supported on DD-WRT.
Though it appears StrongSwan is in the source for dd-wrt. Having said that it doesnt appear to be included in this build?
I have been googling and searching without success. Is it possible either now or in future builds to utilise StrongSwan?
Posted: Wed Dec 02, 2015 20:34 Post subject: bricked
Hi,
I currently not sure whats happening, but i switched boot device (was going to flash stock and then dd-wrt again)
and now I can seem to get access to web interface....and i'm not even sure what firmware thats booting...all i got is
two open aps (MarvellAP00 and MarvellAP10) but doesnt get ip if connect and with lan cable the computer doesnt get an ip..
what have I done and is it fixable ?
(the internet led blinks amber) _________________ test...
Posted: Wed Dec 02, 2015 21:05 Post subject: Re: bricked
catohagen wrote:
Hi,
I currently not sure whats happening, but i switched boot device (was going to flash stock and then dd-wrt again)
and now I can seem to get access to web interface....and i'm not even sure what firmware thats booting...all i got is
two open aps (MarvellAP00 and MarvellAP10) but doesnt get ip if connect and with lan cable the computer doesnt get an ip..
what have I done and is it fixable ?
(the internet led blinks amber)
Perhaps you overwrote the partition that contained the stock firmware? Have you tried the reset button procedure described here and here?
