This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build (e.g. 28320_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. PLEASE ALSO DO NOT RESPOND TO SUCH QUESTIONS! This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless.
If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build. _________________ [I prefer answere in whole sentence]
Your reports for Broadcom units are highly appreciated !
Router:
Firmware:
Kernel:
Status:
Reset:
Errors: _________________ THERE ARE NO STRANGERS HERE; ONLY FRIENDS YOU HAVEN'T YET MET.
________________________________________________________________________________________________________
DD-WRT CHANGELOG | DEVICES | DD-WRT BUILDS | KONG BUILDS | UNOFFICIAL BUILDS | DD-WRT in VIRTUALBOX
Last edited by KrypteX on Sat Dec 12, 2015 8:43; edited 3 times in total
Router: Asus RT-AC68U
Firmware: DD-WRT v3.0-r28320 std (11/25/15)
Kernel:3.10.93 #4985 SMP Tue Nov 24 08:59:38 CET 2015 armv7l
Status: Upgraded with no issues
Reset: No
Errors: None
Great work thanks. _________________ Location (urban) - 1x Linksys EA8500 (AP wlan0 & wlan1 enabled)
1x Asus 68u (Repeater Bridge w/VAP) - wl0 disabled
1x Asus 87u (Client Bridge) - wl1 disabled
Router: Linksys WRT54GL v1.1
Firmware: DD-WRT v3.0-r28320 micro (11/25/15)
Kernel: Linux 2.4.37 #42290 Wed Nov 25 06:56:22 CET 2015 mips
Reset: 30-30-30 before and after
Mode: Repeater Bridge
Status: Not Working
Errors: Cannot disable firewall (nothing happens when pressing Save or Apply Settings).
Cannot connect. SSID is broadcasted but keeps asking for the key (WPA2P).
DD-WRT v24-sp2 (08/12/10) micro - build 14929 is working for this setup.
Router: Linksys WRT54GL v1.1
Firmware: DD-WRT v3.0-r28320 mini (11/25/15)
Kernel: Linux 2.4.37 #42281 Wed Nov 25 06:41:52 CET 2015 mips
Reset: 30-30-30 before and after
Mode: Repeater Bridge
Status: Not Working
Errors: Cannot connect. SSID is broadcasted but keeps asking for the key (WPA2P).
DD-WRT v24-sp2 (08/12/10) micro - build 14929 is working for this setup.
Router: EA6900
Firmware: Linksys-ea6900-webflash.bin
Kernel: 3.10.93 #4985 SMP Tue Nov 24 08:59:38 CET 2015 armv7l DD-WRT
Status: Upgraded from r28211
Reset: No
Errors: No
Router: Netgear EX6200
Firmware: DD-WRT v3.0-r28320 mini (11/25/15)
Kernel: Linux 3.10.93 #4986 SMP Wed Nov 25 07:54:11 CET 2015 armv7l
Mode: Repeater Bridge
Status: Updated from r28211 - 2015/11/16
Reset: No
Errors: No
Router Model
TPLINK ARCHER-C7 v2
Firmware Version
DD-WRT v3.0-r28320 std (11/25/15)
Kernel Version
Linux 3.18.24 #6356 Wed Nov 25 05:50:59 CET 2015 mips
Mode: Repeater Bridge
Status: Updated from r28211 - 2015/11/16
Reset: No
Errors: No
Router: Trendnet TEW811DRU
Firmware: DD-WRT v3.0-r28320 mini (11/25/15)
Kernel: Linux 3.10.93 #4986 SMP Wed Nov 25 07:54:11 CET 2015 armv7l
Status: Upgraded from r28211
Reset: Reset factory defaults (menu)
Errors: USB drive not auto-mounting
Seems like everything else is working, but USB drive does not show under auto-mounting,
USB Support menu. dmesg does show it attached. 32GB USB drive formatted as ext2
Tried unplug/plug and rebooting the router. Doesn't work. Flashed back to r28211 and USB auto-mount working with r28211.
Posted: Wed Nov 25, 2015 19:48 Post subject: R7000
Router: NETGEAR R7000
Firmware: DD-WRT v3.0-r28320 std (11/25/15)
Kernel: Linux 3.10.93 #4985 SMP Tue Nov 24 08:59:38 CET 2015 armv7l
Status: Upgraded from r27858
Reset: erase NVRAM, Reset factory defaults upon flashing
Errors: USB drive not auto-mounting although the USB drive is detected.
Update:
It appears the ext4 module is not being loaded on boot. If i manually load the ext4 by "modprobe ext4" and then mount with "mount /dev/sda1 /mnt" it will mount. Before I was receiving an invalid argument error.
Last edited by garibreezy on Wed Nov 25, 2015 19:59; edited 1 time in total
Router: Netgear R6300v2
Firmware: DD-WRT v3.0-r28320 std (11/25/15)
Kernel: Linux 3.10.93 #4985 SMP Tue Nov 24 08:59:38 CET 2015 armv7l
Mode: Access Point - WAN port Assigned to switch
Status: updated from v3.0-r28000M kongac (10/24/15)
Reset: No
Errors: No , uptime 1h, will edit post in a few days _________________ [BROADCOM] NETGEAR R6300v2 (1): DD-WRT v3.0-r37900M kongac (Dec. 3, 2018)
[BROADCOM] NETGEAR R6300v2 (2): DD-WRT v3.0-r37900M kongac (Dec. 3, 2018)
Router: Buffalo WZR-600DHP2
Firmware: DD-WRT v3.0-r28320 std (11/25/15)
Kernel: 3.10.93 #4989 Wed Nov 25 08:03:50 CET 2015 armv7l
Status: Good
Reset: No
Errors: None noticed so far _________________ Buffalo WZR-600DHP
Back to 28211 _________________ Segment 1 XR700 10Gb LAN, 1Gb WAN ISP BS
Wired AP 1 Unifi Wifi 6 LR US 1Gb LAN
Wired AP 2 Unifi Wifi 6 LR US 1Gb LAN
Wired AP 3 Unifi Wifi 6 LR US 1Gb LAN
Syslog Services Asustor 7110T NAS 10GB
NetGear XS716T 10GB Switch
download1.dd-wrt.com/dd-wrtv2/downloads/betas/ (Brain Slayer)
YAMon https://usage-monitoring.com/index.php
