Your reports for Broadcom units are highly appreciated !
This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build (e.g. 28211_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. Please also do not respond to such questions. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless. If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build. _________________ THERE ARE NO STRANGERS HERE; ONLY FRIENDS YOU HAVEN'T YET MET.
DD-WRT CHANGELOG | DEVICES | DD-WRT BUILDS | KONG BUILDS | UNOFFICIAL BUILDS | DD-WRT in VIRTUALBOX
Kernel: Linux 3.10.93 #4957 SMP Mon Nov 16 08:27:04 CET 2015 armv7l
2.4Ghz (NG-mixed) with 40Mhz channel width: OK
5Ghz (AC/N-Mixed) with 80Mhz channel width: OK
VPN Client: OK
Error(s): none yet encountered
Uptime: 2 hours
Linksys E1200 v2
DD-WRT v3.0-r28211 mega (11/16/15)
Linux 3.10.93 #10212 Mon Nov 16 12:22:00 CET 2015 mips
nvram show -- all better than 28139 build and also shows correct in GUI
size: 24434 bytes (237710 left)
this configuration in 28211 nvrambak.bin = 28 KB (25,864 bytes)
this configuration in 28139 nvrambak.bin = 4 KB (8 bytes)
Repeater Bridge working very well --
NOTE: With this router without reset I went from K3.x_mega-28139 to
K2.6_mini-28139 (yes the RB quit working, had to set static IP on comper
to communicate) and then installed k3.x_mega-28211 then RB working again.
Posted: Tue Nov 17, 2015 11:09 Post subject: Asus RT-AC68U & Linksys E2000
asus_rt-ac68u-firmware r28211 (previous r28139)
Kernel: 3.10.93 #4957 SMP Mon Nov 16 08:27:04 CET 2015 armv7l DD-WRT
2.4Ghz (NG-mixed) with 40Mhz channel width: Ok
5Ghz (Mixed) with 80Mhz channel width: Ok
SSH: Ok, with
Telnet: Disabled but tested to work
USB 2.0 storage ext3 mount to JFFS: Ok
USB 3.0 storage EXT3 mount to /mnt: Ok
Samba shared drive: Ok
Site Survey: Ok
Wi-viz 2.4Ghz & 5Ghz: Yes
Uptime: 0:40 hours
dd-wrt.v24-28211_NEWD-2_K3.x_mega-e2000 previous 28139
Kernel 3.10.93 #10212 Mon Nov 16 12:22:00 CET 2015 mips DD-WRT
Site & Wi-viz Survey: Ok
Router: D-Link DIR-890L
Firmware: DD-WRT v3.0-r28211 std (11/16/15)
Kernel: 3.10.93 #4962 SMP Mon Nov 16 08:45:30 CET 2015 armv7l
Errors: None so far
Mode: Client (wl2, other 2 radios in AP mode)
E1200v2 K3.x 28211
Did a GUI reset and a nvram erase -- have to do power cycles also on this box to regain access.
Used nvram BU to restore my RB configuration -- all worked fine. Repeater bridge back up and connecetd without issue.
and no it's 8:00am here -- that pic was taken last night
nvram seems to be in order w/28211 as opposed to previous build ... see this post/pic
even though that was working fine the nvram was obviously in a mess and no working nvram BU.