Your reports are highly appreciated !
Router:
Firmware:
Kernel:
Status:
Reset:
Errors:
This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build (e.g. 27950M_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. Please also do not respond to such questions. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless. If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build. _________________ THERE ARE NO STRANGERS HERE; ONLY FRIENDS YOU HAVEN'T YET MET.
________________________________________________________________________________________________________
DD-WRT CHANGELOG | DEVICES | DD-WRT BUILDS | KONG BUILDS | UNOFFICIAL BUILDS | DD-WRT in VIRTUALBOX
Last edited by KrypteX on Sat Oct 17, 2015 9:02; edited 1 time in total
Router:R7000
Firmware: DD-WRT v3.0-r27950M kongac (10/16/15)
Kernel: Linux 3.10.90 #441 SMP Fri Oct 16 12:13:37 CEST 2015 armv7l
Status: after upgrade from last kong build (9/7) now 14 hrs up in wireless bridge mode on 5 ghz and no issues so far
Reset: No
Errors: No
Posted: Sat Oct 17, 2015 9:03 Post subject: Build 27950 works slower than 27775
On my Netgear R6300V2 with build 27950 I can't have same high download speed as on builtd 27775. On build 27775 I have download speed all time about 220-225 Mb/s, as on 27950 download speed start from 180 and in the end test I have only 140 Mb/s.
Joined: 24 Mar 2015 Posts: 175 Location: Tacoma, Wa
Posted: Sat Oct 17, 2015 9:14 Post subject:
Router: R8000
Firmware: DD-WRT v3.0-r27950M kongac (10/16/15)
Kernel: Linux 3.10.90 #441 SMP Fri Oct 16 12:13:37 CEST 2015 armv7l
Status: Wireless AC behavior change
Reset: Yes
Errors: None
I noticed the my prior wireless configurations stopped working on my AC/N WL-2 radio:
Changing it to the following I'm able to connect again, but I don't know why this stopped working prior to reset.
Any suggestions would be appreciated.
Other than that everything so far is working great! _________________ Routers:
Netgear R8000 - DD-WRT v3.0-r43420 std (06/15/20)
Netgear R9000 - DD-WRT v3.0-r43420 std (06/15/20)
Router: R7000
Firmware: DD-WRT v3.0-r27950M kongac (10/16/15)
Kernel: Linux 3.10.90 #441 SMP Fri Oct 16 12:13:37 CEST 2015 armv7
Reset: No
Errors: SSH tunneling is still not working. Get "Server unexpectedly closed network connection" message once you try to tunnel anything. Reverting back to working DD-WRT v3.0-r27560M kongac (08/08/15).
Posted: Sat Oct 17, 2015 13:15 Post subject: 27950M on WRT1900ACv2
Router Linksys WRT1900ACv2
Router: Linksys WRT1900ACv2
Firmware: DD-WRT v3.0-r27950M std (10/16/15)
Kernel: Linux 3.18.22 #13 SMP Sat Oct 10 22:37:21 CEST
2015 armv7l
Status: Well, up and running i guess
Reset: Clean install
Errors:
Wifi latency on both 2.4Ghz and 5Ghz band are expectionally high (35ms on speedtest.net whereas 17ms is the norm).
Wifi troughput is exceptionally low only about 35mbit on the 5Ghz band.
Joined: 25 Dec 2010 Posts: 295 Location: Twin Cities, MN
Posted: Sat Oct 17, 2015 13:21 Post subject:
MUNGO wrote:
Router: R7000
Firmware: DD-WRT v3.0-r27950M kongac (10/16/15)
Kernel: Linux 3.10.90 #441 SMP Fri Oct 16 12:13:37 CEST 2015 armv7
Reset: No
Errors: SSH tunneling is still not working. Get "Server unexpectedly closed network connection" message once you try to tunnel anything. Reverting back to working DD-WRT v3.0-r27560M kongac (08/08/15).
SSH is working fine on my R7000/R6250. _________________ NETGEAR R9000 | RT | 40134 NETGEAR R7800 | AP | 40134
Last edited by NiTrus on Sat Oct 17, 2015 15:19; edited 1 time in total
Posted: Sat Oct 17, 2015 14:58 Post subject: Re: 27950M on WRT1900ACv2
Giraffe wrote:
Router Linksys WRT1900ACv2
Router: Linksys WRT1900ACv2
Firmware: DD-WRT v3.0-r27950M std (10/16/15)
Kernel: Linux 3.18.22 #13 SMP Sat Oct 10 22:37:21 CEST
2015 armv7l
Status: Well, up and running i guess
Reset: Clean install
Errors:
Wifi latency on both 2.4Ghz and 5Ghz band are expectionally high (35ms on speedtest.net whereas 17ms is the norm).
Wifi troughput is exceptionally low only about 35mbit on the 5Ghz band.
I just did a quick test and can't reproduce this on the 1200AC, I get 150MBit using a crappy dual stream N adapter on the 5G and 120MBit on 2G. I'll try an ac adapter later on.
Also don't see any error regarding sirq (the previous created exceptional high sirq), when running iperf test sirq is around 20% and on idle it is down to 0%, just as expected.
Ping in client mode is not perfect I see 10ms. Ping from client to router is <3ms which is okay.
Last edited by <Kong> on Sat Oct 17, 2015 15:34; edited 1 time in total
Posted: Sat Oct 17, 2015 15:00 Post subject: Re: Build 27950 works slower than 27775
alkanbw wrote:
On my Netgear R6300V2 with build 27950 I can't have same high download speed as on builtd 27775. On build 27775 I have download speed all time about 220-225 Mb/s, as on 27950 download speed start from 180 and in the end test I have only 140 Mb/s.
Disconnect the router from power, wait 60s then connect it again.
Posted: Sat Oct 17, 2015 16:11 Post subject: Re: 27950M on WRT1900ACv2
<Kong> wrote:
Giraffe wrote:
Router Linksys WRT1900ACv2
Router: Linksys WRT1900ACv2
Firmware: DD-WRT v3.0-r27950M std (10/16/15)
Kernel: Linux 3.18.22 #13 SMP Sat Oct 10 22:37:21 CEST
2015 armv7l
Status: Well, up and running i guess
Reset: Clean install
Errors:
Wifi latency on both 2.4Ghz and 5Ghz band are expectionally high (35ms on speedtest.net whereas 17ms is the norm).
Wifi troughput is exceptionally low only about 35mbit on the 5Ghz band.
I just did a quick test and can't reproduce this on the 1200AC, I get 150MBit using a crappy dual stream N adapter on the 5G and 120MBit on 2G. I'll try an ac adapter later on.
Also don't see any error regarding sirq (the previous created exceptional high sirq), when running iperf test sirq is around 20% and on idle it is down to 0%, just as expected.
Ping in client mode is not perfect I see 10ms. Ping from client to router is <3ms which is okay.
Do you need any more info regarding the low troughput on 5Ghz?
Or could you advise me on what settings you are using on you're WRT1200AC? (Settings like channel nr. lower/upper,)
Posted: Sat Oct 17, 2015 17:06 Post subject: Re: 27950M on WRT1900ACv2
Giraffe wrote:
<Kong> wrote:
Giraffe wrote:
Router Linksys WRT1900ACv2
Router: Linksys WRT1900ACv2
Firmware: DD-WRT v3.0-r27950M std (10/16/15)
Kernel: Linux 3.18.22 #13 SMP Sat Oct 10 22:37:21 CEST
2015 armv7l
Status: Well, up and running i guess
Reset: Clean install
Errors:
Wifi latency on both 2.4Ghz and 5Ghz band are expectionally high (35ms on speedtest.net whereas 17ms is the norm).
Wifi troughput is exceptionally low only about 35mbit on the 5Ghz band.
I just did a quick test and can't reproduce this on the 1200AC, I get 150MBit using a crappy dual stream N adapter on the 5G and 120MBit on 2G. I'll try an ac adapter later on.
Also don't see any error regarding sirq (the previous created exceptional high sirq), when running iperf test sirq is around 20% and on idle it is down to 0%, just as expected.
Ping in client mode is not perfect I see 10ms. Ping from client to router is <3ms which is okay.
Do you need any more info regarding the low troughput on 5Ghz?
Or could you advise me on what settings you are using on you're WRT1200AC? (Settings like channel nr. lower/upper,)
Most likely it is client depended, broadcom had lots of issues with ampdu/amsdu handling in the past, which alo caused trouble with android and/apple devices.
I used an Intel 7260 and Netgear A6200 for my tests.
