New build: DD-WRT v3.0 --- 27490 --- 07/06/2015

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware
Goto page Previous  1, 2
Author Message
CloneVince
DD-WRT User


Joined: 31 May 2014
Posts: 219

PostPosted: Mon Jul 06, 2015 19:57    Post subject: Reply with quote
Router: Netgear R7000 (Gateway)
Firmware: DD-WRT v3.0-r27490 (07/06/15) std
Kernel: 3.10.83 #4370 SMP Mon Jul 6 05:17:25 CEST 2015 armv7l
Status: OK
Reset: No
Errors: None

Upgrade by telnet, as usual.

@Kryptex : I prefer upgrade with telnet because I'm only on wifi. With telnet, no deconnection with the file transfer or any other thing which can corrupt upgrade.
Sponsor
SinCalChewy
DD-WRT User


Joined: 09 Nov 2014
Posts: 311
Location: Bakersfield, CA

PostPosted: Tue Jul 07, 2015 4:07    Post subject: Reply with quote
This build seemed to have quite lower throughput than the previous build I was using (27360M), so I rolled back and all seems to be back to normal speeds.

This is on a Linksys e1200v2

_________________

Deployed Routers:
Netgear R7000 - 5x build 44538M
- Gateway: DoT/DoH, CAKE QoS, USB /w Entware
- Second Subnet Gateway: CAKE QoS, USB /w Entware
- Client Bridge x3: USB /w Entware

Spares/Backups/Collection:
Too many to list. I have old routers, bricked routers, weird routers. You name it.
alediniz
DD-WRT Novice


Joined: 14 Mar 2012
Posts: 17

PostPosted: Tue Jul 07, 2015 7:58    Post subject: Reply with quote
Router: Buffalo WZR-600DHP2
Firmware: DD-WRT v3.0-r27490 (07/06/15) std
Previous: 27456
Kernel: Linux 3.10.83 #4374 Mon Jul 6 05:36:48 CEST 2015 armv7l
Status: Working
Reset: No
Errors: None so far
miles01
DD-WRT Novice


Joined: 09 Dec 2006
Posts: 48

PostPosted: Tue Jul 07, 2015 9:24    Post subject: Reply with quote
Router: DIR-890L * 2
firmware: DD-WRT v3.0-r27490 (07/06/15) std (flashed the dir890l version)
Kernel: Linux 3.10.83 #4375 SMP Mon Jul 6 05:41:46 CEST 2015 armv7l
Status: OK
Reset: No
Errors: OK, no change from last, I remove USB drive it's seems to be cause problem on starting router some service won't start. with previoust version.

DIR890l basement -- WDS on AC-- DIR890l main floor --wired-- Ubiquity on the roof
both dir890l use 2.4 ghz interface for client with the ubiquity ns2.
wabe
DD-WRT Guru


Joined: 17 Jun 2006
Posts: 765

PostPosted: Tue Jul 07, 2015 9:51    Post subject: Reply with quote
Router: Asus AC-68U
Status: OK
Reset: No
Errors: None for far

All major functions including Openvpn seem to work

_________________
AC-68U rev. C1 on Build 44483
AC-68U rev. A1 on Build 44483
AC-68U rev. A1 on Build 44340
e3000usr
DD-WRT User


Joined: 09 Jul 2014
Posts: 183

PostPosted: Tue Jul 07, 2015 11:00    Post subject: Reply with quote
Router: E3200
Firmware: K3.x_mega-e3200
Status: OK
Reset: No
Errors: None

Do not use wireless but everything else works. I live dangerously these days, no resets or 30-30-30. I'm sure one day it will brick my old router but I do need an excuse to buy a new one someday. Thank you DD-WRT for such a stable and constantly updated service you provide to us.
James2k
DD-WRT Guru


Joined: 23 Oct 2011
Posts: 549

PostPosted: Tue Jul 07, 2015 19:46    Post subject: Reply with quote
Router: ASUS RT N66U
Firmware: DD-WRT v3.0-r27490 (07/06/15) big
Kernel: 3.10.83
Status: Issues with hotplug_block and TOR
Reset: No
Errors:

I noticed that "startservice_f hotplug_block -f" seemed to be hanging and taking up a lot CPU and RAM, sometimes it actually exhausts all the RAM and causes the router to reboot after only a couple of minutes of starting up from power cycle

USB mount output within the webif has this spammed a lot of times:

Quote:
/dev/sda mounted to swap
/dev/sda mounted to swap


USB still mounts however and sometimes the startservice process does gracefully end, otherwise killing the PID saves the router from dying.

TOR does not startup on boot, even though it is enabled, no daemon is running and netstat does not show any bind to 9050, running manually works OK. Can workaround with a line in rc_startup.

_________________
James

Main router:

Netgear R7000 overclocked to 1.2GHz - DD-WRT v3.0-r35965M kongac

IPv6 6in4 (HE.net), OpenVPN (with PBR and split tunnelling), Entware, dnsmasq with ipset

Easy ipset support for the R7000

VPN speed: Download: 77.96 Mbps Upload: 5.00 Mbps (AES-128-CBC HMAC-SHA1)

Yes you can get 50 Mbps+ with OpenVPN on a R7000 if you configure it properly!

Previous routers:

ASUS RT-N66U - The Dark Knight
WNR2000v3 - Bought on the cheap for someone else, neutered crap
WNR3500Lv1 - First venture into the DD-WRT world
jons
DD-WRT User


Joined: 24 Jan 2011
Posts: 96

PostPosted: Tue Jul 07, 2015 22:03    Post subject: Reply with quote
SinCalChewy wrote:
This build seemed to have quite lower throughput than the previous build I was using (27360M), so I rolled back and all seems to be back to normal speeds.

This is on a Linksys e1200v2


Same with my E900.
Rolled back a few builds and working as usual.
Newbrain
DD-WRT User


Joined: 28 Dec 2013
Posts: 152

PostPosted: Wed Jul 08, 2015 6:58    Post subject: Asus RT-AC68U Reply with quote
asus_rt-ac68u-firmware r27490 (previous r27456)
Kernel: 3.10.83 #4370 SMP Mon Jul 6 05:17:25 CEST 2015 armv7l GNU/Linux
2.4Ghz (NG-mixed) with 40Mhz channel width: Ok
5Ghz (Mixed) with 80Mhz channel width: Ok
SSH: Ok
Telnet: Disabled but tested to work
USB 2.0 storage ext3 mount to JFFS: Ok
USB 3.0 storage EXT3 mount to /mnt: Ok
Samba shared drive: Ok (Had to click "Apply Settings" before SAMBA worked)
Site Survey: Ok
Wi-viz 2.4Ghz & 5Ghz: No, not working in the last many releases
Reset: No, not since R27332
Status: Ok
Uptime: ~18 hours
moodgorning
DD-WRT Novice


Joined: 08 Jul 2015
Posts: 2

PostPosted: Wed Jul 08, 2015 7:23    Post subject: Reply with quote
Router: TP-Link Archer C8
Firmware: DD-WRT v3.0-r27490 (07/06/15) std
Kernel: Linux 3.10.83 #4372 SMP Mon Jul 6 05:29:42 CEST 2015 armv7l
Status: OK
Reset: No
Errors: None

I accidentally flashed the TP-Link Archer C9 build on the TP-Link Archer C8. It seems to work fine

I was unable however to flash it on the Archer C9. kept getting error message -5533 with or without performing a 30/30/30 reset
ghoffman
DD-WRT User


Joined: 03 Jan 2010
Posts: 453

PostPosted: Thu Jul 09, 2015 0:55    Post subject: Reply with quote
on ea6500v1, r27490 runs well:

System
Router Name xxxx22
Router ModelLinksys EA6500
Firmware Version DD-WRT v3.0-r27490 (07/06/15) giga
Kernel VersionLinux 3.10.83 #8855 Mon Jul 6 08:51:37 CEST 2015 mips

MAC AddressXX:XX:XX:XX:XX:78
Hostnamexxxx22
WAN Domain Namexxxx
LAN Domain Namexxxx
Current TimeWed, 08 Jul 2015 19:51:58
Uptime2 days, 9:31

CPU
CPU ModelBroadcom BCM5300 chip rev 1
CPU Cores1
CPU Clock600 MHz
Load Average
3%0.03, 0.02, 0.04
CPU TemperatureWL0 51.07 °C / WL1 46.34 °C

Memory
Total Available
96%125636 kB / 131072 kB
Free
61%76252 kB / 125636 kB
Used
39%49384 kB / 125636 kB
Buffers
9%4332 kB / 49384 kB
Cached
24%11884 kB / 49384 kB
Active
10%5016 kB / 49384 kB
Inactive
26%13080 kB / 49384 kB

Space Usage
NVRAM30.80 KB / 256 KB
CIFS(Not mounted)
JFFS2(Not mounted)

Network
IP Filter Maximum Ports4096
Active IP Connections
1%57
jwh7
DD-WRT Guru


Joined: 25 Oct 2013
Posts: 2594
Location: Indy

PostPosted: Thu Jul 09, 2015 3:25    Post subject: Reply with quote
I got this build running yesterday on a WRT54GL v1.1 (./broadcom/ dir) that had been on OpenWRT (donated from a friend). TFTP'd via Serial CFE break to dd-wrt.v24_mini_wrt54g.bin, then set password, reset defaults, update via GUI to dd-wrt.v24_vpn_generic.bin, set password, reset defaults, set password, set up incl. clkfreq to 250...and good to go. Kernel 2.4.x (not connected to it now to post the specifics); tested WiFi and LAN as gateway...no issues.
Reference this for further discussions on this:
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=284255


Last edited by jwh7 on Wed Jul 15, 2015 20:51; edited 1 time in total
repomanz
DD-WRT Novice


Joined: 26 Aug 2014
Posts: 9

PostPosted: Fri Jul 10, 2015 18:40    Post subject: build 27490 openvpn issue? Reply with quote
Hi everyone.

I'm running a e4200 with the 27490 build and I'm not sure if I've encountered a bug with the build or a gap in my networking knowledge and doing something wrong.

I have validated that the ddwrt install guide at PIA works with my build/router for my entire network however i have possibly ran into an issue with policy based routing.

Because I only have a few machines I want to secure I'm attempting to use the Policy based routing feature within the openvpn client settings.

I enter my client IP address (10.180.24.5/24) within the policy based routing field, save and apply.

when i do this; i'm broke. I have to perform a hard reset and re-import my backup.

10.180.24.1 is router IP
10.180.24.5 is the client IP
255.255.255.0 is the subnet mask

Is it possible i'm doing something wrong here or have I encountered a bug? I wish I could offer some kind of debug but doing the steps above I have to hard reset; i can't get to the router at all.
AlexPPC
DD-WRT Novice


Joined: 12 Jun 2009
Posts: 14

PostPosted: Sun Sep 13, 2015 23:26    Post subject: Buffalo WZR-600DHP2. AOSS Button missed ? Reply with quote
Hi all,

I got a Buffalo WZR-600DHP2 unit, with the following release of the firmware: 3.0.b27490 07/06/15 std.
In my modest opinion, it's running well, and all general settings are active and up.
Except one.
In Services tab, there is a menu for AOSS Button.
There are two radio buttons there:
1. For making this button to Turn On/Off the Wireless;
2. To Turn Off the Wireless at boot.

No matter which combination of Enable/Disable of the radio buttons I put, the AOSS button doesn't Switch On or Off the Wireless. I press it with a single push. Or I hold it for 3, 5, 10 seconds. I restarted the router in-between too, with no luck.

PS. I forgot to tell that the Reset Button was: Enabled.


Last edited by AlexPPC on Wed Sep 23, 2015 23:12; edited 1 time in total
melbachi
DD-WRT Novice


Joined: 11 Oct 2015
Posts: 1
Location: USA

PostPosted: Tue Oct 27, 2015 19:34    Post subject: Reply with quote
Router: Trendnet TEW828DRU
Firmware: DD-WRT v3.0-r27490 (07/06/15) std
Kernel: Linux 3.10.83 #4376 SMP Mon Jul 6 05:45:01 CEST 2015 armv7l
Status: OK
Reset: No
Errors: Wireless connections sometimes unstable for a few secs.

_________________
[BROADCOM]Tew828dru v.1.0.5.0 --> DD-WRT v3.0-r27490 std (07/06/15)
Goto page Previous  1, 2 Display posts from previous:    Page 2 of 2
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum