Your reports for Broadcom units are highly appreciated !
Router:
Firmware:
Kernel:
Status:
Reset:
Errors:
This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build. (e.g. 27360_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless. If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build. _________________ THERE ARE NO STRANGERS HERE; ONLY FRIENDS YOU HAVEN'T YET MET.
________________________________________________________________________________________________________
DD-WRT CHANGELOG | DEVICES | DD-WRT BUILDS | KONG BUILDS | UNOFFICIAL BUILDS | DD-WRT in VIRTUALBOX
Last edited by KrypteX on Sun Jun 21, 2015 14:23; edited 5 times in total
Router: netgear-wndr4500
Firmware: DD-WRT v3.0-r27360 (06/18/15) giga
Kernel: Linux 3.10.80 #8599 Thu Jun 18 07:49:03 CEST 2015 mips
Status: Working
Reset: No
Errors: None
Router: DIR-890L * 2
firmware: DD-WRT v3.0-r27360 (06/18/15) std (flashed the dir890l version)
Kernel:
Linux 3.10.80 #4299 SMP Thu Jun 18 04:52:27 CEST 2015 armv7l
Status: OK
Reset: No
Errors: 1- WDS sync but I need and order to sync the first one is the router had the wan connection. 2- AC interface with VHT 80 obtain 216 Mb maximum speed and no selectable channel, is he reason i put to HT40, i obtain +-400 mb.
DIR890l basement -- WDS on AC-- DIR890l main floor --wired-- Ubiquity on the roof
both dir890l use 2.4 ghz interface for client with the ubiquity ns2.
WNDR3700v3
DD-WRT v3.0-r27360 (06/18/15) mega (GUI shows as Netgear WNDR4000)
Linux 3.10.80 #8615 Thu Jun 18 08:00:48 CEST 2015 mips
[dd-wrt.v24-27360_NEWD-2_K3.x_mega-nv64k.bin]
Reset from previous
DD-WRT v3.0-r27343 (06/17/15) mega (GUI shows as Netgear WNDR4000)
Linux 3.10.80 #8553 Wed Jun 17 09:45:24 CEST 2015 mips
[dd-wrt.v24-27343_NEWD-2_K3.x_mega-nv64k.bin]
Repeater Bridge mode to WNDR3700v4/r37360 on 2.4GHz
Working well!!!
After setup VAP & its security I had to reboot before a client could connect to VAP.
Using different WPA2-AES on VAP also works well.
Couple mobile devices connected without a problem.
NOTE: Anytime I changed SSID or security on VAP I had to reboot before it worked.
Thanks For Fixing The Repeater Bridge
EDIT:
E2500
DD-WRT v3.0-r27360 (06/18/15) mega
Linux 3.10.80 #8615 Thu Jun 18 08:00:48 CEST 2015 mips
[dd-wrt.v24-27360_NEWD-2_K3.x_mega-e2500.bin]
reset from previous
DD-WRT v3.0-r27332 (06/16/15) mega
Linux 3.10.80 #8525 Tue Jun 16 12:20:20 CEST 2015 mips
[dd-wrt.v24-27332_NEWD-2_K3.x_mega-e2500.bin]
Repeater Bridge works very well.... same as on the WNDR3700v3 .. have to do a reboot to get settings in order or cannot connect to VAP
I like it -
Looks like we have a bunch of new IP Filter Settings I haven't noticed before
.. humm, I don't have them on the atheros WNDR3700v4 w/ 27360
Last edited by mrjcd on Thu Jun 18, 2015 16:24; edited 1 time in total
Router: Linksys 610Nv2 >> e3000
Previous: dd-wrt.v24-26947_NEWD-2_K3.x_mega.bin
Current: dd-wrt.v24-27360_NEWD-2_K3.x_mega.bin
Kernel: Linux 3.10.80 #8615 Thu Jun 18 08:00:48 CEST 2015 mips
Status: Working fine as client on 5GHz
Reset: 30-30-30 before and after flash
Errors: None _________________ Netgear N900v1 > WNDR4500:
dd-wrt.v24-33555_NEWD-2_K3.x_mega-WNDR4500.bin
Linksys WRT610Nv2 > E3000:
dd-wrt.v24-36247_NEWD-2_K3.x_mega.bin
Linksys E1200v1:
dd-wrt.v24-29519_NEWD-2_K2.6_mini-nv64k
Router: Linksys E2000
Firmware: dd-wrt.v24-27360_NEWD-2_K3.x_mega-2000.bin
Kernel: Linux 3.10.80 #8615 Thu Jun 18 08:00:48 CEST 2015 mips
Status: Working as an AP and cleint bridge
Reset: Yes
Errors: No
Last edited by rickW on Sat Jun 20, 2015 20:04; edited 1 time in total
E2500 w/ v3.0-r27332 (06/16/15) mega
Repeater Bridge mode
uptime 7:58
One mobile device has been connected all day plus two others for last hour.. ...and, yea my comper is also still wired connected
No errors - No problems
rickW wrote:
router: Linksys E2000
Firmware: dd-wrt.v24-27360_NEWD-2_K3.x_mega-2000.bin
Kernel: Linux 3.10.80 #8615 Thu Jun 18 08:00:48 CEST 2015 mips
Status: Working as an AP and cleint bridge
Reset: Yes
Errors: DOES NOT WORK AS REPEATER BRIDGE. Cannot connect to the VAP with any type of security or no security.
I'm surprised the E2000 is not working in RB mode. I actually first installed 27360 (on E2500) over the previous build with a non-working RB setup --- that was a disaster. Had to erase NVRAM and start over. Creating VAP --> saved --> set WPA2-AES --> saved and then hit Apply seemed to crash the GUI/http for several minutes. Restart browser, cleared cache log back in and hit Apply again seemed to work. Then had to restart router before it all worked.
So, I also dont see a reason why the E2000 wouldnt work
Might be some lingering artifact in the NVRAM. It's been argued the 30-30-30 isn't necessary but I have -- in the least done a GUI factory reset, CL NVRAM erase, 30-30-30-30-30-30 reset and said ugly words before I could get some configurations to work.
For wireless network mode I always match what I'm connected to and it works for me -
Repeating a 5 GHz radio I use N-Only cause N-Only is all I ever set on a 5 GHz radio.
G-Only connected to any WRT54G.
NG-Mixed on everything else.
That's just standard settings for me. Make sure all other setting are correct for RB mode and it should work. good luck --
I'm going to update the E1200v2 and see what happens with it.
Linksys E1200 v2
reset - previous - try to install over
DD-WRT v24-sp2 (05/09/15) mega - build 26866M
Linux 3.10.77 #7849 Sat May 9 07:55:47 CEST 2015 mips
I always try that and it never works on these boxes as Mr SinCalChewy has told me
It went into firmware management mode. Install 21061 and then to
[dd-wrt.v24-27360_NEWD-2_K3.x_mega-nv64k.bin]
DD-WRT v3.0-r27360 (06/18/15) mega
Linux 3.10.80 #8615 Thu Jun 18 08:00:48 CEST 2015 mips
Repeater Bridge mode works great on the E1200v2.
I am currently connected with my phone to the VAP on the E1200v2 which is repeater bridged to
the VAP on the E2500 which is repeater bridged to my main router.
And using different WPA2 AES security on the VAP
It's all good -
Router: Linksys E900
Version DD-WRT v3.0-r27360 (06/18/15) mega
Kernel VersionLinux 3.10.80 #8615 Thu Jun 18 08:00:48 CEST 2015 mips
Reset: Yes, when downgraded to mini
Errors; None
Works great as a AP, Client Bridge, Repeater Bridge
Note: For repeater bridge, wireless has to be in mixed mode. It does not connect in NG-Mixed
Note1: Works even better when OC´d @400
before this build.
EDIT: After a day, the router suddenly started to refuse connections to the VAP as it used to berofore. I tried erasing NVRAM and reconfiguring with no luch. Will reflash and report
Last edited by rickW on Sat Jun 20, 2015 4:34; edited 1 time in total
Posted: Fri Jun 19, 2015 5:26 Post subject: Updated from 08/12/10 micro - build 14929
...has been a wireless client bridge for my parents for a couple years.
Router: WRT54GSv6
Firmware: DD-WRT v3.0-r27360 (06/18/15) micro
Kernel: Linux 2.4.37 #41046 Thu Jun 18 03:41:37 CEST 2015 mips
Status: Flashed ok, booted ok, adjusted ok...won't be in service (will be gateway) until tomorrow [Update: the condo internet wasn't set up, so can't test WAN yet]
Reset: Reset defaults before and after
Errors: Nothing yet [Update: can't get WAN yet but wireless is working fine]
[Update2: Since I know this was keeping y'all up at night...the wife finally got the modem and hooked it up on July 5th...all is working well, enough at least for her. ]
Last edited by jwh7 on Thu Jul 09, 2015 3:31; edited 1 time in total
