TL-WR1043ND V1 bricked / SOLVED !!!

Post new topic   Reply to topic    DD-WRT Forum Index -> Atheros WiSOC based Hardware
Goto page 1, 2  Next
Author Message
vladtheodor
DD-WRT Novice


Joined: 15 Jan 2012
Posts: 21

PostPosted: Fri Feb 06, 2015 20:23    Post subject: TL-WR1043ND V1 bricked / SOLVED !!! Reply with quote
"Resetting...

U-Boot 1.1.4 (Mar 19 2014 - 11:06:29)

AP83 (ar9100) U-boot 0.0.11
DRAM:
sri
32 MB
id read 0x100000ff
flash size 8MB, sector count = 128
Flash: 8 MB
Using default environment

In: serial
Out: serial
Err: serial
Net: ag7100_enet_initialize...
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
eth0 up
eth0
is_auto_upload_firmware=0
Autobooting in 1 seconds## Booting imagebootm at bf020000 ...
Uncompressing Kernel Image ... Error: Bad gzipped data
GUNZIP ERROR - must RESET board to recover."


Last edited by vladtheodor on Sun Feb 08, 2015 23:29; edited 2 times in total
Sponsor
vladtheodor
DD-WRT Novice


Joined: 15 Jan 2012
Posts: 21

PostPosted: Fri Feb 06, 2015 20:32    Post subject: TL-WR1043ND V1 bricked Reply with quote
jtag
tpl (copy/paste)
erase(d) 0xbf020000 +7c0000
static IP changed to 192.168.0.5
uploaded with tftp2
cp.b help 0xbf020000 0x7c0000
bootm 0xbf020000
tryied images with/without bootloader

nothing helps, what can i do next ?
ghoffman
DD-WRT User


Joined: 03 Jan 2010
Posts: 453

PostPosted: Fri Feb 06, 2015 21:17    Post subject: Reply with quote
i'm assuming you are leaving adequate time for flashing to actually occur? the serial console output should show the flash activity.

the ip address of this router sometimes change to 192.168.24.1 after flashing. i have my computer set to have fixed ip addresses at 192.168.0.9, 192.168.1.9, 192.168.2.9, 192.168.10.9, and 192.168.24.9. keeps most bases covered.

try this and check all .1 addresses for pings.
vladtheodor
DD-WRT Novice


Joined: 15 Jan 2012
Posts: 21

PostPosted: Fri Feb 06, 2015 22:20    Post subject: Reply with quote
Thank you very much for info !!!
I can't find my routers ip via "ipconfig /all", the only way to comunicate with is only via tftp (prolific usb). Via cable (telnet/ssh) network "is not rechargeable". Should i try something via cable ?

And this "reset - Perform RESET of the CPU" - how can i use this to save settings before "cp.b help" and "bootm 0xbf020000" ?

(using pumpkin/tftp2)
ckm
DD-WRT User


Joined: 27 Sep 2014
Posts: 90
Location: usa

PostPosted: Sat Feb 07, 2015 3:15    Post subject: Reply with quote
look at this it will help you out.

https://www.youtube.com/watch?v=IHNrnLnLakE

Read this you will do just fine.

http://www.dd-wrt.com/phpBB2/viewtopic.php?t=68793&highlight=wr1043nd
TendaW311R+
DD-WRT User


Joined: 19 Oct 2011
Posts: 354

PostPosted: Sat Feb 07, 2015 10:00    Post subject: Reply with quote
YOU DON'T NEED SERIAL TO RECOVER WITH MY METHOD Wink

Read this: https://forum.openwrt.org/viewtopic.php?id=46371 there is recovery mode in your bootloader(see is_auto_recovery in bootlog in first post Very Happy )

Download this archive and follow steps: ( http://www.dd-wrt.com/phpBB2/download.php?id=29248

Use this firmware instead of this in archive you downloaded
vladtheodor
DD-WRT Novice


Joined: 15 Jan 2012
Posts: 21

PostPosted: Sat Feb 07, 2015 17:35    Post subject: Reply with quote
I think i will install XP first (somewhere).
Can be troubles from Windows 7, actually running.
Still have this messages in Putty, now no responses from server, yesterday tftp2 uploaded (some)...
Have downloaded ipscan, i see only me.

Thank you for you responses till now !!!!!!
vladtheodor
DD-WRT Novice


Joined: 15 Jan 2012
Posts: 21

PostPosted: Sun Feb 08, 2015 5:46    Post subject: (Rebooting 30/30/30-style) no tpl Reply with quote
"is_auto_upload_firmware=1
update start...
dup 1 speed 1000
Using eth0 device
TFTP from server 192.168.0.66; our IP address is 192.168.0.86
Filename 'wr1043nv1_tp_recovery.bin'.
Load address: 0x80800000
Loading: T T T T
Retry count exceeded; starting again
## Booting image at bf020000 ...
Uncompressing Kernel Image ... Error: Bad gzipped data
GUNZIP ERROR - must RESET board to recover"


Last edited by vladtheodor on Sun Feb 08, 2015 6:50; edited 2 times in total
vladtheodor
DD-WRT Novice


Joined: 15 Jan 2012
Posts: 21

PostPosted: Sun Feb 08, 2015 6:12    Post subject: (Rebooting 30/30/30-style) no tpl Reply with quote
"is_auto_upload_firmware=1
update start...
dup 1 speed 1000
Using eth0 device
TFTP from server 192.168.0.66; our IP address is 192.168.0.86
Filename 'wr1043nv1_tp_recovery.bin'.
Load address: 0x80800000
Loading: T T T T
Abort
new id = aaaaaaaa, new ver = aaaaaaaaauto update firmware: product id verify fai l!
Autobooting in 1 seconds## Booting image at bf020000 ...
Uncompressing Kernel Image ... Error: Bad gzipped data
GUNZIP ERROR - must RESET board to recover"


Last edited by vladtheodor on Sun Feb 08, 2015 6:49; edited 2 times in total
vladtheodor
DD-WRT Novice


Joined: 15 Jan 2012
Posts: 21

PostPosted: Sun Feb 08, 2015 6:25    Post subject: Using "tftpboot 0x81000000"-command without reboot Reply with quote
"Using eth0 device
TFTP from server 192.168.0.5; our IP address is 192.168.0.2
Filename 'wr1043nv1_tp_recovery.bin'.
Load address: 0x81000000
Loading: T T T T
Retry count exceeded; starting again
Using eth0 device
TFTP from server 192.168.0.5; our IP address is 192.168.0.2
Filename 'wr1043nv1_tp_recovery.bin'.
Load address: 0x81000000
Loading: T T T T
Retry count exceeded; starting again"


Last edited by vladtheodor on Sun Feb 08, 2015 6:48; edited 2 times in total
vladtheodor
DD-WRT Novice


Joined: 15 Jan 2012
Posts: 21

PostPosted: Sun Feb 08, 2015 6:34    Post subject: Reply with quote
Something is missing here...

"Load address: 0x80800000"
or
"Load address: 0x81000000"
!???

I still cannot upload like yesterday through "tftp2"...
Disabled UAC (user access control) and firewall (Router Tools v4.3.0)...

What are the proper commands for TL-WR1043ND V1
V1
V1
V1
... ?

And i have Nvidia network-adapter, i see another IP adress in Tftpd32...
Should i totally disable adapter or other things ?
I removed all printer, webcam... from usb...
Bad ip, bad!!! Very Happy

My TTL-adapter have a pin between +3V3 and VCC, if i remove that i see no more TTL-usb in PC...
TendaW311R+
DD-WRT User


Joined: 19 Oct 2011
Posts: 354

PostPosted: Sun Feb 08, 2015 18:24    Post subject: Reply with quote
In my opinion seems that the LAN cable or LAN card are problematic. Try with another PC and another LAN cable. Did you follow exactly the steps in Tutorial I posted ?

About addresses: Use recovery mode, don't use use random addresses and erase commands. Use recovery mode and you will be 200% sure not to erase wrong partition

Upload images of tftp settings and error messages if there
vladtheodor
DD-WRT Novice


Joined: 15 Jan 2012
Posts: 21

PostPosted: Sun Feb 08, 2015 22:19    Post subject: Reply with quote
Yes, i will try another PC (and lan card).
I remember that for years ago i debricked the same router on Asus eepc/intel through udp-cable without jtag.
vladtheodor
DD-WRT Novice


Joined: 15 Jan 2012
Posts: 21

PostPosted: Sun Feb 08, 2015 23:25    Post subject: Reply with quote
EASY RECOVERED !!!

Downloaded archive, Tftpd32, changed ip to 192.168.0.66 and...
PUT YOUR LAN CABLE IN THE LAN (yellow) PORT (NOT IN WAN)!!!

Thank you Tenda !!!

(now must unsold all wire, jtag was not necessary)
TendaW311R+
DD-WRT User


Joined: 19 Oct 2011
Posts: 354

PostPosted: Mon Feb 09, 2015 9:34    Post subject: Reply with quote
Glad to help you buddy Very Happy
This procedure must work for WAN and LAN ports. The important part is that the router is working again. No need to unsolder atleast there is no contact/shorts between serial/jtag pins Cool

Did you understant where was the problem with transfer ?
Goto page 1, 2  Next Display posts from previous:    Page 1 of 2
Post new topic   Reply to topic    DD-WRT Forum Index -> Atheros WiSOC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum