Joined: 13 Jun 2006 Posts: 1608 Location: SE Michigan USA
Posted: Wed Dec 24, 2014 15:27 Post subject:
stalonge wrote:
Am i not sure if its time to celebrate .. but r7000 runs with no reboots for a day ( 24 Hours ) ..
@stalonge
I know you said you had reboots before this build. With this build are you running with the default of wl0ampdu=auto? If so maybe Kong has hit on something to make the r7000 more stable. Going to be out of town for next few days and need stable network while gone but will give this build a try if folks report no reboots with defaults.
--bill _________________ Unifi Security Gateway:Unifi Firmware Netgear r7800:Voxel Firmware Modem:Netgear CM500V voice and Data. ISP:Comcast tutorial for flashing "WRT" series: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=287813 DD-WRT Installation, Upgrade & Basic Setup–Cliff Notes: http://www.dd-wrt.com/phpBB2/viewtopic.php?t=311117 Kong DD-WRT Config Tutorial: http://www.instructables.com/id/Install-and-Configure-a-DD-WRT-Kong-Router/ I tried to be normal once. Worst 2 minutes ever.
So far ddtb (Hardware NAT) has NOT been re-introduced into dd-wrt firmware for the R7000.
I have been looking for them to re-enable that feature too.
I suspect that it is low on the priority list & unless a dev himself wants/needs it we wont get it anytime soon. _________________ Router currently owned:
Netgear R7800 - Router
Netgear R7000 - AP mode
Joined: 03 Dec 2013 Posts: 95 Location: Walldorf/DE
Posted: Wed Dec 24, 2014 18:14 Post subject:
slidermike wrote:
So far ddtb (Hardware NAT) has NOT been re-introduced into dd-wrt firmware for the R7000.
I have been looking for them to re-enable that feature too.
I suspect that it is low on the priority list & unless a dev himself wants/needs it we wont get it anytime soon.
I suspect everything related to R7000 isn't in the priority list... _________________ R7000 - was on BS 25628 - reverted back to original firmware until random reboots get fixed
AC87U - 3.0.0.4_376.48_4 RMerlin doing GPON PPPOE through VLAN
Up and running with build 25700M for 30 hours, no reboots or anything unexpected. (Note that the reboot issue has not been a problem with my setup so far.)
One problem I've had recently has to do with my Roku StreamingStick losing the 5Ghz N-only connection. At the same time I upgraded to 25700M I moved the Roku to a different HDMI connection on my TV. Instead of sticking out of the back of the TV, it's now sticking out of the side. This change in location and orientation gives me a better (and hopefully more stable) wireless connection. I'll keep an eye on this over the next few days and see if the connection holds.
EDIT: Oh well, the connection did not hold. However, I am going to point the finger at the StreamingStick itself (for now). Checking the Roku support forum, I see several complaints regarding the StreamingStick losing wifi connectivity. _________________ Netgear R7000: v3.0-r54248 std (11/29/23)
EdgeRouter-X: EdgeOS v2.0.9-hotfix 7
Last edited by hurleyp on Fri Dec 26, 2014 19:06; edited 1 time in total
I just updated my AC68U and seems ok however my AC speed is now very low. used too get 800 to 1000 Mbps now can't get over 200. I saved my setting before the firmware update and reloaded them. Did another reset and still my AC/5ghz channel is not going over 200.
Factory reset and don't reload your saved settings, put them in manually.
If that works then your saved settings are off or incompatible. _________________ Router currently owned:
Netgear R7800 - Router
Netgear R7000 - AP mode
