Posted: Thu Oct 23, 2014 1:54 Post subject: Belkin F7d7302, F7D8301
Hi all,
Belkin F7d7302 v1 note: Performed 30/30/30 for every test.
Issues k2.6:
1.Wont flash straight from r21676(mega) GUI, had to go into CFE mode and upload dd-wrt.v24-25139_NEWD2_K2.6_mini_f7d7302.bin first then upgraded to Mega version. Same issues regardless whether is mini or mega.
1.Unable to flash straight from Gui and since there is no Mini builds cant try CFE. Only 3.x Build that flashed was initial one from BrainSlayer but router was bricked meaning no Lan nor Wifi.
I also own a Belkin 8301v1, basically same as the 7302v1 plus gigabit Lan, 5ghz wireless and dual USB. Havent tried new r25139 but it presents same issues as the F7d7302v1 on previous firmwares.
k3.x >> when selecting partitions to share on ftp or samba, it will show either "/mnt" or "/mnt/sda_part2"
just my opinion here, but i think its best that people who have linksys E series routers are better off with tomato here. i dont think the newer builds are going to fully work properly on these older routers.
long live the newer routers, right? if im wrong, please correct me.
Netgear R6250 running build 25139
spams "/dev/sda mounted to swap" in usb. i have a mnt, jffs, opt, and swap partition. in fact, it spams so many, the web page freezes.
i do look forward to the next build. i saw a lot of features that looked like they were worth testing, but i did not have the time to do that and only test basic features that i use. _________________ For people who are new to the dd-wrt forums >> http://www.catb.org/~esr/faqs/smart-questions.html#rtfm
barryware wrote:
It takes a "community" to raise a router..
Internet Connection 1
Some Techicolor modem > Linksys WRT3200ACM
Internet connection 2
Ubiquiti Powerbeam Gen 2 > Netgear R9000
Official (but not really) dd-wrt General Discussion element/matrix chat
I've only been up online with it on my Buffalo WZR-1750DHP(D) for a few minutes, but PPTP was the first thing I tested and PPTP clients (internal from my network to external PPTP servers) function 100% properly thus far. Multiple clients simultaneously, etc. All work. Previously I had to use nothing newer than Kong's 24800M for this to function. Nice work, BS. Thanks for everything!
Obviously if anything comes up I'll report it here but thus far... so far so good.
25139 - asus_rt-ac68u-firmware.trx RT-AC68R - primary router/gateway
2.4Ghz (NG-mixed) with 20Mhz channel width => OK
5Ghz (Mixed) with 80Mhz channel width => OK
Guest-Vlan 2.4Ghz => OK
SSH => OK
Telnet => OK
Port Forward => OK
WOL over the Internet => OK
VNC Repeater = OK
USB 2.0 storage ext3 mount to JFFS => OK
USB 3.0 storage NTFS mount to MNT => OK
NAS Samba shared drive = OK
PPTP Server => No Connection With Client From WAN
Wi-viz 2.4Ghz & 5Ghz => OK
25139 - dd-wrt-25139-Asus_RT-AC66.trx RT-AC66U - primary router/gateway
2.4Ghz (NG-mixed) with 20Mhz channel width => OK
5Ghz (Mixed) with 80Mhz channel width => OK
Guest-Vlan 2.4Ghz => OK
SSH => OK
Telnet => OK
Port Forward => OK
WOL over the Internet => OK
USB storage ext3 mount to JFFS => OK
USB storage NTFS mount to MNT => OK
NAS Samba shared drive = OK
PPTP Server => No Connection With Client From WAN
Wi-viz 2.4Ghz & 5Ghz => OK _________________ Netgear XR500, R7800
Asus AC87Ua1
Repeater Bridge
Netgear R6400v2otp
