New BS release (r25139-testing)

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware
Goto page Previous  1, 2
Author Message
JAMESMTL
DD-WRT Guru


Joined: 13 Mar 2014
Posts: 856
Location: Montreal, QC

PostPosted: Wed Oct 22, 2014 23:26    Post subject: Reply with quote
@ nitrus. Did mine exactly as above and it's working fine. Will send debug questions via PM
_________________
IPv6 Ready - HE IPv6 Tunnel
http://test-ipv6.com (10/10)
http://ipv6-test.com (20/20)
http://test-ipv6.netiter.dk (20/20)

Sponsor
NiTrus
DD-WRT User


Joined: 25 Dec 2010
Posts: 295
Location: Twin Cities, MN

PostPosted: Thu Oct 23, 2014 1:26    Post subject: Reply with quote
**FYI**
my AP reads as a WNDR4000...should be WNDR3700v3..
everything works fine tho..



wndr3700v3.PNG
 Description:
 Filesize:  2.17 KB
 Viewed:  12919 Time(s)

wndr3700v3.PNG



_________________
NETGEAR R9000 | RT | 40134
NETGEAR R7800 | AP | 40134

torankusu
DD-WRT User


Joined: 11 Feb 2013
Posts: 61

PostPosted: Thu Oct 23, 2014 1:54    Post subject: Belkin F7d7302, F7D8301 Reply with quote
Hi all,

Belkin F7d7302 v1

note: Performed 30/30/30 for every test.

Issues k2.6:

1.Wont flash straight from r21676(mega) GUI, had to go into CFE mode and upload dd-wrt.v24-25139_NEWD2_K2.6_mini_f7d7302.bin first then upgraded to Mega version. Same issues regardless whether is mini or mega.

2.Wireless still wont work since r22118, Sysinfo displays wireless as on, stuck on channel-1 and no Tx power, even though under wireless tab it is on and channel 6. telnet/ssh shows wireless mode stuck on Ad Hoc.
Reference tickets:
http://svn.dd-wrt.com/ticket/3377 <-- Master ticket.
http://svn.dd-wrt.com/ticket/3653
http://svn.dd-wrt.com/ticket/3496

Log:
root@DD-WRT:~# wl status
SSID: "dd-wrt"
Mode: Ad Hoc RSSI: 0 dBm noise: -20 dBm Channel: 1
BSSID: 00:00:00:00:00:00 Capability: IBSS
Supported Rates: [ 1(b) 2(b) 5.5(b) 6 9 11(b) 12 18 24 36 48 54 ]
802.11N Capable:
Chanspec: 2.4GHz channel 1 20MHz (0x2b01)
Control channel: 1
802.11N Capabilities:
Supported MCS : [ 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 ]

Issues K3.x:

1.Unable to flash straight from Gui and since there is no Mini builds cant try CFE. Only 3.x Build that flashed was initial one from BrainSlayer but router was bricked meaning no Lan nor Wifi.

I also own a Belkin 8301v1, basically same as the 7302v1 plus gigabit Lan, 5ghz wireless and dual USB. Havent tried new r25139 but it presents same issues as the F7d7302v1 on previous firmwares.

Thanks.



Snap 2014-10-22 at 21.44.47.jpg
 Description:
 Filesize:  8.24 KB
 Viewed:  12891 Time(s)

Snap 2014-10-22 at 21.44.47.jpg


Gameman Advanced Kid
DD-WRT Guru


Joined: 18 Nov 2012
Posts: 904

PostPosted: Thu Oct 23, 2014 2:24    Post subject: Reply with quote
E3000 running r25139

i only test what i commonly use.

K2.6 >> wireless does not work.

k3.x >> when selecting partitions to share on ftp or samba, it will show either "/mnt" or "/mnt/sda_part2"

just my opinion here, but i think its best that people who have linksys E series routers are better off with tomato here. i dont think the newer builds are going to fully work properly on these older routers.

long live the newer routers, right? if im wrong, please correct me.

Netgear R6250 running build 25139

spams "/dev/sda mounted to swap" in usb. i have a mnt, jffs, opt, and swap partition. in fact, it spams so many, the web page freezes.

i do look forward to the next build. i saw a lot of features that looked like they were worth testing, but i did not have the time to do that and only test basic features that i use.

_________________
Is everything okay?

WDS AP - R7800
WDS STATION - R7500V2
the_antix
DD-WRT Novice


Joined: 17 Sep 2014
Posts: 16

PostPosted: Thu Oct 23, 2014 6:20    Post subject: Reply with quote
on R7000, it spams "/dev/sda mounted to swap" in usb tab so many times that the page freezes.
ddaniel51
DD-WRT Guru


Joined: 19 Feb 2013
Posts: 1392

PostPosted: Thu Oct 23, 2014 6:40    Post subject: Reply with quote
My 7000 usb tab has three entries, one for each properly formatted/named partition on the usb stick.

How is your usb formatted?
the_antix
DD-WRT Novice


Joined: 17 Sep 2014
Posts: 16

PostPosted: Thu Oct 23, 2014 6:57    Post subject: Reply with quote
ext3 and swap
DaveTheNerd
DD-WRT User


Joined: 15 Jul 2008
Posts: 317

PostPosted: Thu Oct 23, 2014 7:03    Post subject: Reply with quote
I've only been up online with it on my Buffalo WZR-1750DHP(D) for a few minutes, but PPTP was the first thing I tested and PPTP clients (internal from my network to external PPTP servers) function 100% properly thus far. Multiple clients simultaneously, etc. All work. Previously I had to use nothing newer than Kong's 24800M for this to function. Nice work, BS. Thanks for everything!

Obviously if anything comes up I'll report it here but thus far... so far so good. Wink
gotofbi
DD-WRT Novice


Joined: 05 Jul 2012
Posts: 12

PostPosted: Thu Oct 23, 2014 7:41    Post subject: Reply with quote
Router: Asus RT-N16
was running: Kong 22000++
firmware: dd-wrt.v24-25139_NEWD-2_K3.x-big-RT-N16.trx

1. After flash, Falls into boot-loop (reboot every 3sec).
2. Kills Wifi (even after flashing original firm, no wifi signal)
cybero2912
DD-WRT Guru


Joined: 18 Jun 2006
Posts: 1190
Location: Berlin

PostPosted: Thu Oct 23, 2014 12:04    Post subject: Reply with quote
flashed micro generic on WRT54G2 -
says successfully at the end of process but router does not come up after reboot.
I will investigate when @home
redhawk0
DD-WRT Guru


Joined: 04 Jan 2007
Posts: 11476
Location: Wherever the wind blows- North America

PostPosted: Thu Oct 23, 2014 12:21    Post subject: Reply with quote
cybero2912 wrote:
flashed micro generic on WRT54G2 -
says successfully at the end of process but router does not come up after reboot.
I will investigate when @home


I get this occasionally with my 310nv1 unit...a power cycle will usually bring it back.

redhawk

_________________
I do NOT provide personal assistance through chat or phone....so please don't ask.
redhawk0
DD-WRT Guru


Joined: 04 Jan 2007
Posts: 11476
Location: Wherever the wind blows- North America

PostPosted: Thu Oct 23, 2014 12:23    Post subject: Reply with quote
gotofbi wrote:
Router: Asus RT-N16
was running: Kong 22000++
firmware: dd-wrt.v24-25139_NEWD-2_K3.x-big-RT-N16.trx

1. After flash, Falls into boot-loop (reboot every 3sec).
2. Kills Wifi (even after flashing original firm, no wifi signal)


You must load build 21530 first to get K3.x working on this model.

Check here for details.

http://www.dd-wrt.com/phpBB2/viewtopic.php?t=269504

redhawk

_________________
I do NOT provide personal assistance through chat or phone....so please don't ask.
cybero2912
DD-WRT Guru


Joined: 18 Jun 2006
Posts: 1190
Location: Berlin

PostPosted: Thu Oct 23, 2014 13:07    Post subject: Reply with quote
successfully flashed an ancient Asus "WL-500g Deluxe" Very Happy
jrscs
DD-WRT User


Joined: 09 Aug 2010
Posts: 252

PostPosted: Thu Oct 23, 2014 13:24    Post subject: Reply with quote
25139 - asus_rt-ac68u-firmware.trx
RT-AC68R - primary router/gateway
2.4Ghz (NG-mixed) with 20Mhz channel width => OK
5Ghz (Mixed) with 80Mhz channel width => OK
Guest-Vlan 2.4Ghz => OK
SSH => OK
Telnet => OK
Port Forward => OK
WOL over the Internet => OK
VNC Repeater = OK
USB 2.0 storage ext3 mount to JFFS => OK
USB 3.0 storage NTFS mount to MNT => OK
NAS Samba shared drive = OK
PPTP Server => No Connection With Client From WAN
Wi-viz 2.4Ghz & 5Ghz => OK

25139 - dd-wrt-25139-Asus_RT-AC66.trx
RT-AC66U - primary router/gateway
2.4Ghz (NG-mixed) with 20Mhz channel width => OK
5Ghz (Mixed) with 80Mhz channel width => OK
Guest-Vlan 2.4Ghz => OK
SSH => OK
Telnet => OK
Port Forward => OK
WOL over the Internet => OK
USB storage ext3 mount to JFFS => OK
USB storage NTFS mount to MNT => OK
NAS Samba shared drive = OK
PPTP Server => No Connection With Client From WAN
Wi-viz 2.4Ghz & 5Ghz => OK

_________________
Asus AC87U A1 - DD-WRT v3.0-r43217 std (05/22/20)
Repeater Bridges(s)
Asus AC68R A1 - DD-WRT v3.0-r43217 std (05/22/20)
Netgear R6400 V2 - DD-WRT v3.0-r43136 std (05/13/20)
Asus AC66U A1 - DD-WRT v3.0-r43136 giga (05/13/20)
cybero2912
DD-WRT Guru


Joined: 18 Jun 2006
Posts: 1190
Location: Berlin

PostPosted: Fri Oct 24, 2014 12:24    Post subject: Reply with quote
do NOT flash this FW on a WRT54G2 !!

I will solder serial to see what is the problem and JTAG for recover on weekend
Goto page Previous  1, 2 Display posts from previous:    Page 2 of 2
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum