[nicky]

This is the istallation the firmware ddwrt on fonera with serial:
RedBoot> fis init
About to initialize [format] FLASH image system - continue (y/n)? y
*** Initialize FLASH Image System
... Erase from 0xa87e0000-0xa87f0000: .
... Program from 0x80ff0000-0x81000000 at 0xa87e0000: .
RedBoot> ip_addr -h 192.168.1.1 -l 192.168.1.254/24
IP: 192.168.1.254/255.255.255.0, Gateway: 0.0.0.0
Default server: 192.168.1.1
RedBoot> fis list
Name FLASH addr Mem addr Length Entry point
RedBoot 0xA8000000 0xA8000000 0x00030000 0x00000000
FIS directory 0xA87E0000 0xA87E0000 0x0000F000 0x00000000
RedBoot config 0xA87EF000 0xA87EF000 0x00001000 0x00000000
RedBoot> load -r -v -b 0x80041000 root.fs
Using default protocol (TFTP)
|
Raw file loaded 0x80041000-0x802cbfff, assumed entry at 0x80041000
RedBoot> fis create -b 0x80041000 -f 0xA8030000 -l 0x002C0000 -e 0x00000000 rootfs
... Erase from 0xa8030000-0xa82f0000: ..........................................
..
... Program from 0x80041000-0x80301000 at 0xa8030000: ..........................
..................
... Erase from 0xa87e0000-0xa87f0000: .
... Program from 0x80ff0000-0x81000000 at 0xa87e0000: .
RedBoot> load -r -v -b 0x80041000 vmlinux.bin.l7
Using default protocol (TFTP)
-
Raw file loaded 0x80041000-0x80100fff, assumed entry at 0x80041000
RedBoot> fis create -r 0x80041000 -e 0x80041000 -l 0x000E0000 vmlinux.bin.l7
... Erase from 0xa82f0000-0xa83d0000: ..............
... Program from 0x80041000-0x80101000 at 0xa82f0000: ............
... Erase from 0xa87e0000-0xa87f0000: .
... Program from 0x80ff0000-0x81000000 at 0xa87e0000: .
RedBoot> fis create -f 0xA83D0000 -l 0x00010000 -n nvram
... Erase from 0xa87e0000-0xa87f0000: .
... Program from 0x80ff0000-0x81000000 at 0xa87e0000: .

I have install firmware ddwrt for fonera http://www.dd-wrt.com/wiki/index.php/Fonera
(Known Good Firmware) Versions 04/16.
The boot fonera is http://paste.debian.net/29068 .
The interfaces fonera are http://paste.debian.net/29069.
Pratically repeat a message:
#Sending discover
#Jan 1 00:01:33 udhcpc[207]: Sending discover
#Sending discover
and error ath0
Can I help me?

[nicky]

I have install firmware ddwrt for fonera http://www.dd-wrt.com/wiki/index.php/Fonera
Versions 10/06/2007
1.
Linux version 2.6.20.11 (root@dd-wrt) (gcc version 4.1.2) #85 Fri May 4 16:56:04
2.
CEST 2007
3.
CPU revision is: 00019064
4.
Determined physical RAM map:
5.
memory: 01000000 @ 00000000 (usable)
6.
Built 1 zonelists. Total pages: 4064
7.
Kernel command line: console=ttyS0,115200 root=/dev/mtdblock1 rootfstype=squashf
8.
s,jffs2 noinitrd
9.
Primary instruction cache 16kB, physically tagged, 4-way, linesize 16 bytes.
10.
Primary data cache 16kB, 4-way, linesize 16 bytes.
11.
Synthesized TLB refill handler (20 instructions).
12.
Synthesized TLB load handler fastpath (32 instructions).
13.
Synthesized TLB store handler fastpath (32 instructions).
14.
Synthesized TLB modify handler fastpath (31 instructions).
15.
PID hash table entries: 64 (order: 6, 256 bytes)
16.
Using 92.000 MHz high precision timer.
17.
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
18.
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
19.
Memory: 13332k/16384k available (1949k kernel code, 3052k reserved, 390k data, 1
20.
28k init, 0k highmem)
21.
Mount-cache hash table entries: 512
22.
NET: Registered protocol family 16
23.
Radio config found at offset 0xf8
24.
NET: Registered protocol family 2
25.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
26.
TCP established hash table entries: 1024 (order: 0, 4096 bytes)
27.
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
28.
TCP: Hash tables configured (established 1024 bind 512)
29.
TCP reno registered
30.
gpio_proc: module loaded and /proc/gpio/ created
31.
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
32.
devfs: boot_options: 0x1
33.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
34.
io scheduler noop registered (default)
35.
Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (now
36.
ayout= 0)
37.
Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled
38.
serial8250: ttyS0 at MMIO 0xb1100003 (irq = 37) is a 16550A
39.
PPP generic driver version 2.4.2
40.
PPP Deflate Compression module registered
41.
PPP BSD Compression module registered
42.
MPPE/MPPC encryption/compression module registered
43.
NET: Registered protocol family 24
44.
IMQ starting with 2 devices...
45.
IMQ driver loaded successfully.
46.
Hooking IMQ before NAT on PREROUTING.
47.
Hooking IMQ after NAT on POSTROUTING.
48.
tun: Universal TUN/TAP device driver, 1.6
49.
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
50.
MTD driver for SPI flash.
51.
spiflash: Probing for Serial flash ...
52.
spiflash: Found SPI serial Flash.
53.
cmdlinepart partition parsing not available
54.
Searching for RedBoot partition table in spiflash at offset 0x7d0000
55.
Searching for RedBoot partition table in spiflash at offset 0x7e0000
56.
7 RedBoot partitions found on MTD device spiflash
57.
Creating 8 MTD partitions on "spiflash":
58.
0x00000000-0x00030000 : "RedBoot"
59.
0x00030000-0x003d0000 : "rootfs"
60.
0x002f0000-0x003d0000 : "vmlinux.bin.l7"
61.
0x003d0000-0x003e0000 : "nvram"
62.
0x003e0000-0x007e0000 : "ddwrt"
63.
0x007e0000-0x007ef000 : "FIS directory"
64.
mtd: partition "FIS directory" doesn't end on an erase block -- force read-only
65.
0x007ef000-0x007f0000 : "RedBoot config"
66.
mtd: partition "RedBoot config" doesn't start on an erase block boundary -- forc
67.
e read-only
68.
0x007f0000-0x00800000 : "board_config"
69.
u32 classifier
70.
OLD policer on
71.
Netfilter messages via NETLINK v0.30.
72.
nf_conntrack version 0.5.0 (128 buckets, 1024 max)
73.
ctnetlink v0.93: registering with nfnetlink.
74.
IPv4 over IPv4 tunneling driver
75.
GRE over IPv4 tunneling driver
76.
ip_tables: (C) 2000-2006 Netfilter Core Team
77.
IPP2P v0.8.2 loading
78.
ClusterIP Version 0.8 loaded successfully
79.
TCP bic registered
80.
TCP cubic registered
81.
TCP westwood registered
82.
TCP highspeed registered
83.
TCP hybla registered
84.
TCP htcp registered
85.
TCP vegas registered
86.
TCP scalable registered
87.
NET: Registered protocol family 1
88.
NET: Registered protocol family 17
89.
Welcome to PF_RING 3.2.1
90.
(C) 2004-06 L.Deri <deri@ntop.org>
91.
NET: Registered protocol family 27
92.
PF_RING: bucket length 128 bytes
93.
PF_RING: ring slots 4096
94.
PF_RING: sample rate 1 [1=no sampling]
95.
PF_RING: capture TX No [RX only]
96.
PF_RING: transparent mode Yes
97.
PF_RING initialized correctly.
98.
PF_RING: registered /proc/net/pf_ring/
99.
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
100.
All bugs added by David S. Miller <davem@redhat.com>
101.
Time: MIPS clocksource has been installed.
102.
VFS: Mounted root (squashfs filesystem) readonly.
103.
Mounted devfs on /dev
104.
Freeing firmware memory: 0kb freed
105.
Freeing unused kernel memory: 128k freed
106.
SET failed on device ath0 ; Invalid argument.
107.
SET failed on device ath0 ; Invalid argument.
108.
SET failed on device ath0 ; Invalid argument.
109.
SIOCGIFFLAGS: No such device
110.
SIOCGIFFLAGS: No such device
111.
SIOCGIFFLAGS: No such device
112.
SIOCGIFFLAGS: No such device
113.
udhcpc (v0.9.9-pre) started
114.
Jan 1 00:00:14 udhcpc[201]: udhcpc (v0.9.9-pre) started
115.
sh: /tmp/.rc_startup: not found
116.
Sending discover...
117.
Jan 1 00:00:15 udhcpc[201]: Sending discover...
118.
Sending discover...
119.
Jan 1 00:00:19 udhcpc[201]: Sending discover...
120.
Sending discover...
121.
Jan 1 00:00:23 udhcpc[201]: Sending discover...
122.
Sending discover...
123.
Jan 1 00:00:40 udhcpc[201]: Sending discover...
124.
Sending discover...
125.
Jan 1 00:00:44 udhcpc[201]: Sending discover...
126.
Sending discover...
127.
Jan 1 00:00:48 udhcpc[201]: Sending discover...
128.
DD-WRT v24 std (c) 2007 NewMedia-NET GmbH
129.
Release: 06/10/07 (SVN revision: 7213)
130.

131.
DD-WRT login: DD-WRT v24 std (c) 2007 NewMedia-NET GmbH
132.
Release: 06/10/07 (SVN revision: 7213)
133.

134.
DD-WRT login: Sending discover...
135.
Jan 1 00:01:58 udhcpc[201]: Sending discover...
#
fconfig
#
ath0 Link encap:Ethernet HWaddr 00:18:84:28:F2:09
#
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
#
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
#
TX packets:176 errors:0 dropped:0 overruns:0 carrier:0
#
collisions:0 txqueuelen:0
#
RX bytes:0 (0.0 B) TX bytes:9152 (8.9 KiB)
#

#
br0 Link encap:Ethernet HWaddr 00:18:84:28:F2:09
#
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
#
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
#
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
#
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
#
collisions:0 txqueuelen:0
#
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
#

#
eth0 Link encap:Ethernet HWaddr 00:18:84:28:F2:08
#
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
#
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
#
TX packets:42 errors:0 dropped:0 overruns:0 carrier:0
#
collisions:0 txqueuelen:1000
#
RX bytes:0 (0.0 B) TX bytes:13566 (13.2 KiB)
#
Interrupt:4 Base address:0x1000
#

#
eth0:0 Link encap:Ethernet HWaddr 00:18:84:28:F2:08
#
inet addr:169.254.255.1 Bcast:169.254.255.255 Mask:255.255.0.0
#
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
#
Interrupt:4 Base address:0x1000
#

#
lo Link encap:Local Loopback
#
inet addr:127.0.0.1 Mask:255.0.0.0
#
UP LOOPBACK RUNNING MULTICAST MTU:16436 Metric:1
#
RX packets:6 errors:0 dropped:0 overruns:0 frame:0
#
TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
#
collisions:0 txqueuelen:0
#
RX bytes:348 (348.0 B) TX bytes:348 (348.0 B)
#

#
wifi0 Link encap:Ethernet HWaddr 00:18:84:28:F2:09
#
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
#
RX packets:18 errors:0 dropped:0 overruns:0 frame:9530
#
TX packets:198 errors:0 dropped:0 overruns:0 carrier:0
#
collisions:0 txqueuelen:199
#
RX bytes:2178 (2.1 KiB) TX bytes:14102 (13.7 KiB)
#
Interrupt:3 Memory:b0000000-b00ffffc


Pratically repeat a message:
#Sending discover
#Jan 1 00:01:33 udhcpc[207]: Sending discover
#Sending discover
and error ath0
Can I help me?[/quote]