New build is out 23720 (BS) K2.6 and K3.X

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware
Goto page Previous  1, 2, 3  Next
Author Message
Smart-Travler
DD-WRT Novice


Joined: 14 Mar 2014
Posts: 8

PostPosted: Fri Mar 14, 2014 20:59    Post subject: W Reply with quote
Cannot upgrade Netgear WNDR4000 to dd-wrt.v24-23720_NEWD-2_K2.6_big-nv64k.bin

Tried twice failed to upgrade.
Sponsor
Malachi
DD-WRT Guru


Joined: 17 Jul 2012
Posts: 7246
Location: Columbus, Ohio

PostPosted: Fri Mar 14, 2014 21:18    Post subject: Re: W Reply with quote
Smart-Travler wrote:
Cannot upgrade Netgear WNDR4000 to dd-wrt.v24-23720_NEWD-2_K2.6_big-nv64k.bin

Tried twice failed to upgrade.

It's probably too big.

_________________
I am far from a guru, I'm barely a novice.
Smart-Travler
DD-WRT Novice


Joined: 14 Mar 2014
Posts: 8

PostPosted: Fri Mar 14, 2014 21:29    Post subject: Reply with quote
Interesting looks like the size difference between 21676 big and 23720 big is 68K
kingcharles
DD-WRT Novice


Joined: 15 Mar 2014
Posts: 4

PostPosted: Sat Mar 15, 2014 14:56    Post subject: Netgear WNR3500L Reply with quote
Router Model Netgear WNR3500 v2/U/L v1
Firmware Version DD-WRT v24-sp2 (08/19/13) vpnkong - build 22200M
Kernel Version Linux 2.6.24.111 #608 Mon Aug 19 23:27:32 CEST 2013 mips

GUI upgrade to dd-wrt.v24-23720_NEWD-2_K3.x_mega.bin FAILED.

The GUI showed a succesful upgrade but after the reboot nothing was changed so the firmware remained.

Do I have to install dd-wrt.v24-23720_NEWD-2_K3.x_mega-WNR3500L.chk first when coming from the KONG build?

Thanks
CDMMocelet
DD-WRT User


Joined: 02 Nov 2008
Posts: 55

PostPosted: Sat Mar 15, 2014 15:01    Post subject: Re: WNDR4000 K2.6 upgrade Reply with quote
I have been running 3.x on my WNDR4000 for quite some time with success. Might be time to step to the 3.x loads. I know it doesn't help with this upgrade issue, but it does side step it. Very Happy

Smart-Travler wrote:
Cannot upgrade Netgear WNDR4000 to dd-wrt.v24-23720_NEWD-2_K2.6_big-nv64k.bin

Tried twice failed to upgrade.
redhawk0
DD-WRT Guru


Joined: 04 Jan 2007
Posts: 11451
Location: Wherever the wind blows- North America

PostPosted: Sat Mar 15, 2014 16:28    Post subject: Reply with quote
barryware wrote:
Hi Red.. Not to get this thread off topic but I have run builds past 19XXX on my N16 with no wireless issues. Currently, my N16 is not in service.


Depends on the mode...I run my unit in Repeater Mode...that wasn't "fixed" until 23xxx.

redhawk

_________________
I do NOT provide personal assistance through chat or phone....so please don't ask.
mutiny
DD-WRT Novice


Joined: 31 Mar 2011
Posts: 36

PostPosted: Mon Mar 17, 2014 11:15    Post subject: Reply with quote
40MHz wifi on E2000 has horrible stability, 20MHz works great though.
-XPTO-
DD-WRT User


Joined: 20 Jan 2014
Posts: 52

PostPosted: Mon Mar 17, 2014 12:52    Post subject: E4200 V1 All good with K3.x Reply with quote
Web upgrade with no reset from 23598 K3. Everything is working fine. WiFi steady both in 2.4 and 5GHz.
godzilla1984
DD-WRT Novice


Joined: 09 Feb 2014
Posts: 3

PostPosted: Wed Mar 19, 2014 11:54    Post subject: Reply with quote
Router : Asus RT-N12 C1

dd-wrt.v24-23720_NEWD-2_K2.6_mini_RT-N12C1.trx - no wireless at all. In status ( wireless ) displays channels "-1 and 3". Wired network function ok.

dd-wrt.v24-23720_NEWD-2_K3.x_mega_RT-N12C1.trx - no boot, bootloop.
bskchaos
DD-WRT User


Joined: 07 Feb 2009
Posts: 198

PostPosted: Wed Mar 19, 2014 15:00    Post subject: Reply with quote
Asus N12.B1, K3x bootloop.

Serial output:

Quote:
Decompressing...done


CFE version 5.100.138.9 based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: ¤G 1¤ë 17 16:59:52 CST 2012 (root@myvm1110hdd-vm)
Copyright (C) 2000-2008 Broadcom Corporation.

Init Arena
Init Devs.
Boot partition size = 131072(0x20000)
Found an ST compatible serial flash with 128 64KB blocks; total size 8MB
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.100.138.9
CPU type 0x19749: 300MHz
Tot mem: 32768 KBytes

CFE mem: 0x80700000 - 0x80799720 (628512)
Data: 0x8072F560 - 0x80732790 (12848)
BSS: 0x80732790 - 0x80733720 (3984)
Heap: 0x80733720 - 0x80797720 (409600)
Stack: 0x80797720 - 0x80799720 (8192)
Text: 0x80700000 - 0x8072F560 (193888)

Device eth0: hwaddr C8-60-00-AB-49-1C, ipaddr 192.168.1.1, mask 255.255.255.0
gateway not set, nameserver not set
end of nvram_rescuegpio_init
Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
Loading: CFE works as TFTP Server.
Failed.
Could not load :: Timeout occured
Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
Loading: .. 3708 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
Linux version 3.10.33 (root@dd-wrt.buildserver) (gcc version 4.7.3 20121106 (prerelease) (Linaro GCC 4.7-2012.11) ) #1649 Thu Mar 13 14:22:47 CET 2014
CPU revision is: 00019749 (MIPS 74Kc)
Found an ST compatible serial flash with 128 64KB blocks; total size 8MB
found nvram at 7E0000
something wrong here. do not remap
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Zone ranges:
Normal [mem 0x00000000-0x01ffffff]
HighMem empty
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x00000000-0x01ffffff]
Primary instruction cache 32kB, 4-way, VIPT, I-cache aliases, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd init=/bin/sh
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 25556k/32768k available (4421k kernel code, 7212k reserved, 1664k data, 308k init, 0k highmem)
NR_IRQS:128
CPU: BCM53572 rev 1 at 300 MHz
bcm947xx_clockevent_set_mode: 1
bcm947xx_clockevent_set_mode: 3
console [ttyS0] enabled
Calibrating delay loop... 148.88 BogoMIPS (lpj=744448)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
PCI: no core
PCI: no core
PCI: scanning bus 0
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
pci_bus 0000:00: root bus resource [mem 0x00000000-0xffffffff]
pci_bus 0000:00: root bus resource [bus 00-ff]
PCI: Fixing up bus 0
Switching to clocksource MIPS
NET: Registered protocol family 2
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
msgmni has been set to 49
alg: No test for stdrng (krng)
io scheduler noop registered (default)
HDLC line discipline maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = Cool is a U6_16550A
brd: module loaded
pflash: found no supported devices
try to find cfe size up to 8388608
bootloader size: 131072
nvram size: 65536
bcmsflash: Filesystem type: squashfs, size=0x589ee6
partition size = 0
Updating TRX offsets and length:
old trx = [0x0000001c, 0x00000930, 0x001ec000], len=0x00777000 crc32=0x3d27c514
new trx = [0x0000001c, 0x00000930, 0x001ec000], len=0x00780000 crc32=0xf18dc37d
Done
Creating 5 MTD partitions on "bcmsflash":
0x000000000000-0x000000020000 : "cfe"
0x000000020000-0x0000007f0000 : "linux"
0x00000020c000-0x0000007a0000 : "rootfs"
mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
mtd: partition "rootfs" set to be root filesystem
0x0000007f0000-0x000000800000 : "nvram"
0x0000007a0000-0x0000007f0000 : "ddwrt"
brcmnand: found no supported devices
nflash: found no supported devices
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
et_module_init: passivemode set to 0x0
et_module_init: txworkq set to 0x0
et_module_init: et_txq_thresh set to 0x0
et0: online cpus 1
eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.37.14.62 (r437318)
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP Deflate Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
Broadcom Watchdog Timer: 0.07 initialized.
u32 classifier
Performance counters on
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (399 buckets, 1596 max)
nf_conntrack_rtsp v0.6.21 loading
xt_time: kernel timezone is -0000
ip_set: protocol 6
gre: GRE over IPv4 demultiplexor driver
nf_nat_rtsp v0.6.21 loading
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP: bic registered
TCP: cubic registered
TCP: westwood registered
TCP: highspeed registered
TCP: hybla registered
TCP: htcp registered
TCP: vegas registered
TCP: veno registered
TCP: scalable registered
TCP: lp registered
TCP: yeah registered
TCP: illinois registered
NET: Registered protocol family 17
Bridge firewalling registered
8021q: 802.1Q VLAN Support v1.8
startup nvram driver
found nvram
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 308K (805f3000 - 80640000)
start service
starting Architecture code for broadcom
starting hotplug
Jan 1 00:00:13 udevtrigger[738]: parse_config_file: can't open '/etc/udev/udev.conf' as config file: No such file or directory

done
boardnum
boardtype
boardrev
nvram invalid, erase
Booting device: Linksys WRT54G/GL/GS
loading switch-core
loading switch-robo
roboswitch: Probing device 'eth0'
roboswitch: trying a 5325! at eth0
roboswitch: found a 5325! at eth0
boardflags are 0x0000
[USB] checking...
Some error found, we want to reboot!.....................
kill -15 -1: No such file or directory
sleep 3: No such file or directory
kill -9 -1: No such file or directory
umount -a -r: No such file or directory
/etc/preinit: line 66: can't create /proc/sys/net/ipv4/ip_conntrack_max: nonexistent directory
/etc/preinit: line 66: can't create /proc/sys/net/ipv4/ip_conntrack_max: nonexistent directory
eth1: Operation not supported
wl0.1: No such device
wl0.2: No such device
wl0.3: No such device
eth1: Operation not permitted
nbw = 20
channel 6, val 20
0, 1000, 0, 6
spec 1006

eth1: Operation not supported
Sending SIGTERM to all processesBCMDOG: WDT device closed unexpectedly. WDT will not stop!

Sending SIGKILL to all processes
Restarting system.
Please stand by while rebooting the system...
dhunt2
DD-WRT Novice


Joined: 19 Mar 2014
Posts: 20

PostPosted: Wed Mar 19, 2014 23:36    Post subject: Success - R23720 TP-Link TL-WR1043ND and D-Link DIR-632a Reply with quote
R23720

TP-Link TL-WR1043ND (V1)
D-Link DIR-632a

Upgraded from 23598. No issues and no errors. Both units seem very stable. (Stable on 23598 also)
MELERIX
DD-WRT Novice


Joined: 09 Mar 2014
Posts: 40
Location: Chile

PostPosted: Thu Mar 20, 2014 11:10    Post subject: Reply with quote
Hardware: Linksys WRT54G v8.2
Flash: dd-wrt.v24_micro_generic.bin

Methode: TFTP.
Flash: Ok, Without troubles.
Reset settings: Yes 30/30/30.
Errors:
- Apply changes in router and it take several minutes to restart (sometimes 2-3 minutes).
- UPNP doesn't work properly, enable UPNP and apply the changes, router restarts automatically as should, but then UPNP still don't work, so you need to unplug power and connect again, and then works, but not always.
- When you are exploring the router admin panel, sometimes it stop responding (but router's lights are ok) and is impossible to use internet or enter in router admin panel, you have to unplug power and connect it again to recover the router.
- If you connect a second computer to the router, after few minutes (2-3 minutes) the internet and router admin panel stop working, but lan communication between PCs works normally.
- Reset button in the router doesn't work properly, this button should reset router (fast reset) with a single push, but don't work.
- UPNP Forwards list doesn't show anything.


Last edited by MELERIX on Sat Mar 22, 2014 6:16; edited 1 time in total
DoesItMatter
DD-WRT Guru


Joined: 10 May 2008
Posts: 1373
Location: Pacific North West, USA

PostPosted: Fri Mar 21, 2014 18:46    Post subject: Reply with quote
Upgraded Linksys E3000 from Fractal K2.6 23040 to BS/Kong K3.X Mega 23720

Working fine, both 2.4Ghz and 5Ghz radios working

Signal seems fine on both channels so far

Nice and fast speedtest.net results as well



-----------------------------

Edit: Had to downgrade my Linksys E3000 back to Fractal's 23040 build

The wireless started acting weird for both 2.4Ghz and 5Ghz

_________________
Evil or Very Mad Soylent Green Is People ! Evil or Very Mad
Twisted Evil =-=-=-=-=-=-=-=-=-=-= Twisted Evil
2x Asus RT-N16 - Asuswrt-Merlin 3.0.0.4.376.43
Belkin F7D3302 - Toastman Tomato USB VPN 1.28.7505
Linksys E3000 - Toastman Tomato USB VPN 1.28.7505
-------------------------
2x Buffalo WZR-HP-G300NH V1 - OpenWRT Chaos Calmer 45860
2x Engenius ESR900 - Stock Firmware 1.4.0 / OpenWRT Chaos Calmer 45860
TP-Link WR1043ND V1.8 - Gargoyle 1.7.1
McKatsu
DD-WRT Novice


Joined: 24 Mar 2014
Posts: 1

PostPosted: Mon Mar 24, 2014 2:34    Post subject: Reply with quote
I've found on the ASUS RT-N16 that if you disable the SSID broadcast it will start the wireless interface, then you can re-enable it and it will work fine. A pain to hook up a cable every time you need to reboot but it works.
Zippy1970
DD-WRT Novice


Joined: 02 Sep 2012
Posts: 19

PostPosted: Mon Mar 24, 2014 19:27    Post subject: Reply with quote
Cisco/Linksys E4200

v24-23720_NEWD-2_K2.6_mega-nv60k.bin:
  • Wireless interfaces not starting (no wireless at all).

v24-23720_NEWD-2_K3.x_mega-e4200.bin:
  • Wireless interfaces working OK.
  • WAN speed (wired) has significantly dropped from ~110Mbps to ~70Mbps



With v24_21061_NEWD-2_K2.6_big-nv60k:


With v24-23720_NEWD-2_K3.x_mega-e4200.bin:
Goto page Previous  1, 2, 3  Next Display posts from previous:    Page 2 of 3
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum