New build is out 21676 (BS) K2.6 and K3.X

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware
Goto page 1, 2, 3, 4, 5, 6  Next
Author Message
kt_haddock
DD-WRT Guru


Joined: 25 Dec 2009
Posts: 710

PostPosted: Mon May 27, 2013 13:20    Post subject: New build is out 21676 (BS) K2.6 and K3.X Reply with quote
ftp://dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/2013/05-27-2013-r21676/
RT-AC66U K2.6 (wrong directory)
ftp://dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/2013/05-27-2013-r21676/linksys-ea2700/
EA2700 K2.6 (wrong directory)
ftp://dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/2013/05-27-2013-r21676/asus-rt-ac66u/

This build thread is for reporting successes and problem with loading this experimental test build. This is important info for developers and users. Always state your hardware and SPECIFIC build. (eg: 19342_NEWD-2_K2.6_mega-nv64k.bin). Do not ask questions about your specific router or how to configure it in this thread; create your own thread to discuss any specific problems you have or need resolved. This thread is to report info, not to seek it. Posts that do not add to understanding this build will be deleted. Make sure you know how to flash properly and the risk before using this build. It is important to adhere to these requirements, to keep this thread from becoming impossibly long and useless. If you don't know what build to flash and how to flash properly and have a means of recovery if things should go wrong, do NOT flash this experimental test build.

_________________
[I prefer answere in whole sentence]


Last edited by kt_haddock on Mon May 27, 2013 16:02; edited 6 times in total
Sponsor
LOM
DD-WRT Guru


Joined: 28 Dec 2008
Posts: 7632

PostPosted: Mon May 27, 2013 13:32    Post subject: Reply with quote
dd-wrt.v24-21676_NEWD-2_K3.x_big.bin running fine on my RT-N16
jtrosky
DD-WRT Guru


Joined: 17 Apr 2009
Posts: 627
Location: Philadelphia, PA

PostPosted: Mon May 27, 2013 15:42    Post subject: Reply with quote
Just a quick note about this build.

The firmware files for the Asus RT-AC66U and the Linksys EA2700 have been put into each others directories - so if you are looking for teh RT-AC66U firmware, it's actually in the "ea2700" directory.

And the Linksys EA2700 firmware file in actually in the "asus-rt-ac66u" directory.

Hopefully, I can save a few folks from flashing the wrong file!

_________________
1 x Linksys WRT160n v3
1 x Linksys WRT310n v1
1 x Linksys WRT600n v1.1
1 x Linksys WRT610n v1
1 x Linksys E2500
1 x Netgear WNDR3300
1 x Dlink DIR-825 v1
2 x Asus RT-AC66U
LOM
DD-WRT Guru


Joined: 28 Dec 2008
Posts: 7632

PostPosted: Mon May 27, 2013 16:12    Post subject: Reply with quote
The broadcom_K3X-EXPERIMENTAL folder contains quite a few files which shouldn't be there - mega builds 7.5MB in size for routers which only has 4MB flash.

Be aware of your routers flash size before trying any files in this folder!
Malachi
DD-WRT Guru


Joined: 17 Jul 2012
Posts: 7221
Location: Columbus, Ohio

PostPosted: Mon May 27, 2013 21:07    Post subject: Reply with quote
Loaded it on an ea2700, only the 2.4ghz radio was showing. After restore to factory default the router is bricked. Request time out to pings, lan lights on, the power light does not come on.
30/30/30 does nothing.

Fractal, I know you said you have serial connected to your ea2700. Is it like the other linksys, with the square being ground, the one next to it unused, the next two for tx/Rx?
My USB to TTL serial cable is scheduled to arrive this week.

_________________
I am far from a guru, I'm barely a novice.
stalonge
DD-WRT Guru


Joined: 21 Jul 2006
Posts: 1865
Location: Fortaleza Ce Brazil

PostPosted: Tue May 28, 2013 2:30    Post subject: Reply with quote
My E3000 is working fine with this k3 build ..
NOW samba share is working perfectly ....

Thanks devs

Very Happy Very Happy

_________________
DDwrt ...it rocks ....
1 R8500 41556 AP OpenVPN webserver RETIRED (bricked)
1 R7800 42912 AP Wireguard webserver JFFS SAMBA FTP usb HD Mesh
1 R7800 42912 Cli Mesh
1 WZR1750 42908 AP Webserver OpenVPN
1 DDx86 Vmware 40260
1 E3000 41027 K3 @500 WAP wifi client
Magnetron1.1
DD-WRT User


Joined: 21 Nov 2010
Posts: 278
Location: North America

PostPosted: Tue May 28, 2013 3:24    Post subject: Reply with quote
Thanks for the new firmware. Unfortunately the WZR-D1800H_MULTI.trx build 21676 results in a soft brick of the Buffalo WZR-D1800H router. The kernel panics because it can't mount the root file system and forces an endless boot loop. Using the CFE Flash command and the Linux TFTP app, I was able to revert to the WZR-D1800H_MULTI.trx build 21286.

Here's the PuTTY Log of the serial console of an unsuccessful boot using build 21676 :

BUFFALO CFE Version 1.04
Memory Test start(0xA0100000) end(0xA8000000) size(33292288)
Data line test start:0xa0100000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
Address line test start:0xa0100000 len:0x7f00000 pattern 0xAAAAAAAA 0x55555555
Fill test patnum:2
fill Pattern 5555AAAA Writing... Reading...
fill Pattern AAAA5555 Writing... Reading...
Decompressing...done


CFE version 6.30.15.3 (r315282) based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Tue Apr 24 09:04:01 JST 2012 (root@fc15.localdomain)
Copyright (C) 2000-2008 Broadcom Corporation.

Init Arena
Initializing PCI. [normal]
PCI bus 0 slot 0/0: vendor 0x14e4 product 0x0800 (flash memory, rev 0x01)
PCI bus 0 slot 1/0: vendor 0x14e4 product 0x4715 (ethernet network, rev 0x01)
PCI bus 0 slot 4/0: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x10, rev 0x01)
PCI bus 0 slot 4/1: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x20, rev 0x01)
PCI bus 0 slot 5/0: vendor 0x14e4 product 0x0820 (PCI bridge, rev 0x01)
PCI bus 0 slot 6/0: vendor 0x14e4 product 0x0820 (PCI bridge, rev 0x01)
PCI bus 0 slot 7/0: vendor 0x14e4 product 0x052e (undefined subclass 0xff, interface 0xff, rev 0x01)
PCI bus 0 slot 8/0: vendor 0x14e4 product 0x080e (RAM memory, rev 0x01)
PCI bus 0 slot 9/0: vendor 0x14e4 product 0x0534 (undefined subclass 0xff, interface 0xff, rev 0x01)
Init Devs.
Boot partition size = 262144(0x40000)
Found an ST compatible serial flash with 8 64KB blocks; total size 0MB
Found a Samsung (1 bit-cell) NAND flash with 2048B pages or 128KB blocks; total size 128MB
bcm_robo_enable_switch: EEE is disabled
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.15.3 (r315282)
CPU type 0x19749: 600MHz
Tot mem: 131072 KBytes

CFE mem: 0x87000000 - 0x87164A60 (1460832)
Data: 0x8704C9A0 - 0x87050BA0 (16896)
BSS: 0x87050BA0 - 0x87062A60 (73408)
Heap: 0x87062A60 - 0x87162A60 (1048576)
Stack: 0x87162A60 - 0x87164A60 (8192)
Text: 0x87000000 - 0x8704C994 (313748)

DRAM magic offset:00060000 size:00010000
DRAM magic found
Device eth0: hwaddr 12-6F-3F-XX-XX-XX, ipaddr 192.168.11.1, mask 255.255.255.0
gateway not set, nameserver not set
check_trx: start nflash1.trx
check_trx: exit nflash1.trx
Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
Loading: Failed.
Could not load :: Timeout occured
Loader:raw Filesys:raw Dev:nflash0.os File: Options:(null)
Loading: .. 1331212 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
CPU revision is: 00019749 (MIPS 74Kc)
Found an ST compatible serial flash with 8 64KB blocks; total size 0MB
found nvram at 50000
map 32K cfe nvram at 78000
Determined physical RAM map:
memory: 07fff000 @ 00000000 (usable)
Zone ranges:
Normal [mem 0x00000000-0x07ffefff]
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x00000000-0x07ffefff]
Primary instruction cache 32kB, 4-way, VIPT, I-cache aliases, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Linux version 3.9.4 (root@dd-wrt) (gcc version 4.7.3 20121106 (prerelease) (Linaro GCC 4.7-2012.11) ) #124 Mon May 27 10:08:20 CEST 2013
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32511
Kernel command line: console=ttyS0,115200 root=1f05 rootfstype=squashfs noinitrd init=/bin/sh
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
__ex_table already sorted, skipping sort
Writing ErrCtl register=80000be0
Readback ErrCtl register=80000be0
Cache parity protection enabled
Memory: 125620k/131068k available (2993k kernel code, 5448k reserved, 640k data, 264k init, 0k highmem)
NR_IRQS:128
CPU: BCM5300 rev 1 at 600 MHz
bcm947xx_clockevent_set_mode: 1
bcm947xx_clockevent_set_mode: 3
console [ttyS0] enabled
Calibrating delay loop... 299.82 BogoMIPS (lpj=1499136)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
PCI: Initializing host
PCI: Reset RC
PCI: Initializing host
PCI: Reset RC
PCI: scanning bus 0
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
pci_bus 0000:00: root bus resource [mem 0x00000000-0xffffffff]
pci_bus 0000:00: root bus resource [bus 00-ff]
PCI: Fixing up bus 0
pci 0000:00:05.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0000:00:06.0: bridge configuration invalid ([bus 00-00]), reconfiguring
PCI/PCIe coreunit 0 is set to bus 1.
PCI: Fixing up bridge
PCI: Fixing up bridge
PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
PCI: Fixing up bus 1
PCI/PCIe coreunit 1 is set to bus 2.
PCI: Fixing up bridge
PCI: Fixing up bridge
PCI: Enabling device 0000:02:00.1 (0004 -> 0006)
PCI: Fixing up bus 2
Switching to clocksource MIPS
NET: Registered protocol family 2
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
Buffalo D1800H init
squashfs: version 3.0 (2006/03/15) Phillip Lougher
msgmni has been set to 245
alg: No test for stdrng (krng)
io scheduler noop registered (default)
HDLC line discipline maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = Cool is a U6_16550A
serial8250: ttyS1 at MMIO 0x0 (irq = Cool is a U6_16550A
brd: module loaded
pflash: found no supported devices
try to find cfe size up to 524288
no filesys. assume nflash devices
bootloader size: 524288
nvram size: 65536
Creating 2 MTD partitions on "bcmsflash":
0x000000000000-0x000000080000 : "cfe"
0x000000050000-0x000000060000 : "nvram"
Creating 1 MTD partitions on "bcmsflash":
0x000000070000-0x000000080000 : "nvram_cfe"
Found a Samsung NAND flash with 2048B pages or 128KB blocks; total size 128MB
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
nand_read_bbt: bad block at 0x000005300000
nand_read_bbt: bad block at 0x000007a60000
Creating 2 MTD partitions on "brcmnand":
0x000000000000-0x000002000000 : "linux"
0x000002000000-0x000007f00000 : "ddwrt"
lookup_nflash_rootfs_offset: offset = 0x0
found trx at 0, len =18644992
scan filesys at 144C00
nflash: squash filesystem with lzma found at offset 0
Creating 2 MTD partitions on "nflash":
0x000000000000-0x000002000000 : "nandimage"
0x000000144c00-0x000002000000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
add netgear bosrddata for pflash if exists
add netgear bosrddata for sflash if exists
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP Deflate Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
Broadcom Watchdog Timer: 0.07 initialized.
GACT probability NOT on
Mirror/redirect action on
Failed to load ipt action
Simple TC action Loaded
netem: version 1.3
u32 classifier
Performance counters on
input device check on
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1962 buckets, 7848 max)
nf_conntrack_rtsp v0.6.21 loading
xt_time: kernel timezone is -0000
ip_set: protocol 6
gre: GRE over IPv4 demultiplexor driver
nf_nat_rtsp v0.6.21 loading
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP: bic registered
TCP: cubic registered
TCP: westwood registered
TCP: highspeed registered
TCP: hybla registered
TCP: htcp registered
TCP: vegas registered
TCP: veno registered
TCP: scalable registered
TCP: lp registered
TCP: yeah registered
TCP: illinois registered
NET: Registered protocol family 17
Bridge firewalling registered
8021q: 802.1Q VLAN Support v1.8
startup nvram driver
found nvram
found cfe nvram
check if nvram copy is required CFE Size is 32768
nvram copy magic is 48534C46
List of all partitions:
1f00 512 mtdblock0 (driver?)
1f01 64 mtdblock1 (driver?)
1f02 64 mtdblock2 (driver?)
1f03 32768 mtdblock3 (driver?)
1f04 97280 mtdblock4 (driver?)
1f05 32768 mtdblock5 (driver?)
1f06 31469 mtdblock6 (driver?)
No filesystem could mount root, tried: squashfs
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,5) <<== Kernel should be using mtdblock6 (31,6)
Rebooting in 3 seconds..Please stand by while rebooting the system...

End of PuTTY Log of serial console of an unsuccessful boot using build 21676

Here's the PuTTY Log of the serial console of an successful boot using build 21286 :

BUFFALO CFE Version 1.04
Memory Test start(0xA0100000) end(0xA8000000) size(33292288)
Data line test start:0xa0100000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA
Address line test start:0xa0100000 len:0x7f00000 pattern 0xAAAAAAAA 0x55555555
Fill test patnum:2
fill Pattern 5555AAAA Writing... Reading...
fill Pattern AAAA5555 Writing... Reading...
Decompressing...done


CFE version 6.30.15.3 (r315282) based on BBP 1.0.37 for BCM947XX (32bit,SP,LE)
Build Date: Tue Apr 24 09:04:01 JST 2012 (root@fc15.localdomain)
Copyright (C) 2000-2008 Broadcom Corporation.

Init Arena
Initializing PCI. [normal]
PCI bus 0 slot 0/0: vendor 0x14e4 product 0x0800 (flash memory, rev 0x01)
PCI bus 0 slot 1/0: vendor 0x14e4 product 0x4715 (ethernet network, rev 0x01)
PCI bus 0 slot 4/0: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x10, rev 0x01)
PCI bus 0 slot 4/1: vendor 0x14e4 product 0x471a (USB serial bus, interface 0x20, rev 0x01)
PCI bus 0 slot 5/0: vendor 0x14e4 product 0x0820 (PCI bridge, rev 0x01)
PCI bus 0 slot 6/0: vendor 0x14e4 product 0x0820 (PCI bridge, rev 0x01)
PCI bus 0 slot 7/0: vendor 0x14e4 product 0x052e (undefined subclass 0xff, interface 0xff, rev 0x01)
PCI bus 0 slot 8/0: vendor 0x14e4 product 0x080e (RAM memory, rev 0x01)
PCI bus 0 slot 9/0: vendor 0x14e4 product 0x0534 (undefined subclass 0xff, interface 0xff, rev 0x01)
Init Devs.
Boot partition size = 262144(0x40000)
Found an ST compatible serial flash with 8 64KB blocks; total size 0MB
Found a Samsung (1 bit-cell) NAND flash with 2048B pages or 128KB blocks; total size 128MB
bcm_robo_enable_switch: EEE is disabled
et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 6.30.15.3 (r315282)
CPU type 0x19749: 600MHz
Tot mem: 131072 KBytes

CFE mem: 0x87000000 - 0x87164A60 (1460832)
Data: 0x8704C9A0 - 0x87050BA0 (16896)
BSS: 0x87050BA0 - 0x87062A60 (73408)
Heap: 0x87062A60 - 0x87162A60 (1048576)
Stack: 0x87162A60 - 0x87164A60 (8192)
Text: 0x87000000 - 0x8704C994 (313748)

DRAM magic offset:00060000 size:00010000
DRAM magic found
Device eth0: hwaddr 12-6F-3F-XX-XX-XX, ipaddr 192.168.11.1, mask 255.255.255.0
gateway not set, nameserver not set
check_trx: start nflash1.trx
check_trx: exit nflash1.trx
Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
Loading: Failed.
Could not load :: Timeout occured
Loader:raw Filesys:raw Dev:nflash0.os File: Options:(null)
Loading: .. 1312820 bytes read
Entry at 0x80001000
Closing network.
Starting program at 0x80001000
CPU revision is: 00019749 (MIPS 74Kc)
Found an ST compatible serial flash with 8 64KB blocks; total size 0MB
found nvram at 50000
map cfe nvram at 78000
Determined physical RAM map:
memory: 07fff000 @ 00000000 (usable)
Zone ranges:
Normal [mem 0x00000000-0x07ffefff]
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x00000000-0x07ffefff]
Primary instruction cache 32kB, 4-way, VIPT, I-cache aliases, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Linux version 3.8.7 (root@dd-wrt) (gcc version 4.7.3 20121106 (prerelease) (Linaro GCC 4.7-2012.11) ) #162 Mon Apr 15 11:51:57 CEST 2013
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32511
Kernel command line: console=ttyS0,115200 root=1f06 rootfstype=squashfs noinitrd init=/bin/sh
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
__ex_table already sorted, skipping sort
Writing ErrCtl register=80000be0
Readback ErrCtl register=80000be0
Cache parity protection enabled
Memory: 125652k/131068k available (2953k kernel code, 5416k reserved, 639k data, 304k init, 0k highmem)
NR_IRQS:128
CPU: BCM5300 rev 1 at 600 MHz
bcm947xx_clockevent_set_mode: 1
bcm947xx_clockevent_set_mode: 3
console [ttyS0] enabled
Calibrating delay loop... 299.82 BogoMIPS (lpj=1499136)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
PCI: Initializing host
PCI: Reset RC
PCI: Initializing host
PCI: Reset RC
PCI: scanning bus 0
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
pci_bus 0000:00: root bus resource [mem 0x00000000-0xffffffff]
pci_bus 0000:00: root bus resource [bus 00-ff]
PCI: Fixing up bus 0
pci 0000:00:05.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0000:00:06.0: bridge configuration invalid ([bus 00-00]), reconfiguring
PCI/PCIe coreunit 0 is set to bus 1.
PCI: Fixing up bridge
PCI: Fixing up bridge
PCI: Enabling device 0000:01:00.1 (0004 -> 0006)
PCI: Fixing up bus 1
PCI/PCIe coreunit 1 is set to bus 2.
PCI: Fixing up bridge
PCI: Fixing up bridge
PCI: Enabling device 0000:02:00.1 (0004 -> 0006)
PCI: Fixing up bus 2
Switching to clocksource MIPS
NET: Registered protocol family 2
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
Buffalo D1800H init
squashfs: version 3.0 (2006/03/15) Phillip Lougher
msgmni has been set to 245
alg: No test for stdrng (krng)
io scheduler noop registered (default)
HDLC line discipline maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = Cool is a U6_16550A
serial8250: ttyS1 at MMIO 0x0 (irq = Cool is a U6_16550A
brd: module loaded
pflash: found no supported devices
try to find cfe size up to 524288
no filesys. assume nflash devices
bootloader size: 524288
nvram size: 65536
Creating 3 MTD partitions on "bcmsflash":
0x000000000000-0x000000080000 : "cfe"
0x000000050000-0x000000060000 : "nvram"
0x000000070000-0x000000080000 : "nvram_cfe"
Found a Samsung NAND flash with 2048B pages or 128KB blocks; total size 128MB
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
nand_read_bbt: bad block at 0x000005300000
nand_read_bbt: bad block at 0x000007a60000
Creating 2 MTD partitions on "brcmnand":
0x000000000000-0x000002000000 : "linux"
0x000002000000-0x000007f00000 : "ddwrt"
lookup_nflash_rootfs_offset: offset = 0x0
found trx at 0, len =18444288
scan filesys at 140400
nflash: squash filesystem with lzma found at offset 0
Creating 2 MTD partitions on "nflash":
0x000000000000-0x000002000000 : "nandimage"
0x000000140400-0x000002000000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
PPP generic driver version 2.4.2
PPP BSD Compression module registered
PPP Deflate Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
Broadcom Watchdog Timer: 0.07 initialized.
GACT probability NOT on
Mirror/redirect action on
Simple TC action Loaded
netem: version 1.3
u32 classifier
Performance counters on
input device check on
Actions configured
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1963 buckets, 7852 max)
nf_conntrack_rtsp v0.6.21 loading
xt_time: kernel timezone is -0000
ip_set: protocol 6
gre: GRE over IPv4 demultiplexor driver
nf_nat_rtsp v0.6.21 loading
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP: bic registered
TCP: cubic registered
TCP: westwood registered
TCP: highspeed registered
TCP: hybla registered
TCP: htcp registered
TCP: vegas registered
TCP: veno registered
TCP: scalable registered
TCP: lp registered
TCP: yeah registered
TCP: illinois registered
NET: Registered protocol family 17
Bridge firewalling registered
8021q: 802.1Q VLAN Support v1.8
startup nvram driver
found nvram
found cfe nvram
VFS: Mounted root (squashfs filesystem) readonly on device 31:6. <<== Compare with the same line in the above console log
Freeing unused kernel memory: 304k freed
start service
starting Architecture code for broadcom
starting hotplug

=============================================================================
=============================================================================

root@WZR-D1800HRT5:~# cat /tmp/loginprompt
DD-WRT v24-sp2 giga (c) 2013 NewMedia-NET GmbH
Release: 04/15/13 (SVN revision: 21286)

root@WZR-D1800HRT5:~# uname -a
Linux WZR-D1800HRT5 3.8.7 #162 Mon Apr 15 11:51:57 CEST 2013 mips GNU/Linux

End of PuTTY Log of serial console of an successful boot using build 21286

It would be helpful if the SVN number were included in the firmware file name.


- Magnetron1.1
devil-strike
DD-WRT User


Joined: 18 Jun 2006
Posts: 87
Location: Netherlands

PostPosted: Tue May 28, 2013 8:40    Post subject: Reply with quote
Malachi wrote:
Loaded it on an ea2700, only the 2.4ghz radio was showing. After restore to factory default the router is bricked. Request time out to pings, lan lights on, the power light does not come on.
30/30/30 does nothing.

Fractal, I know you said you have serial connected to your ea2700. Is it like the other linksys, with the square being ground, the one next to it unused, the next two for tx/Rx?
My USB to TTL serial cable is scheduled to arrive this week.


From wich firmware you upgraded to dd-wrt? I using the old style Linksys firmware but the ea2700 wont even load, i upload the trx file is says flashed succesfull afterthat it goes 4times to bootloader mode en afterthat the old Linksys firmware is back.

I think the boatloader is switching to second linux partion(some sort of failsafe)

_________________
WRT320N
Zyxel NBG-460N
Tp-Link WR-1043ND
Linksys E3200
Malachi
DD-WRT Guru


Joined: 17 Jul 2012
Posts: 7221
Location: Columbus, Ohio

PostPosted: Tue May 28, 2013 9:28    Post subject: Reply with quote
devil-strike wrote:
Malachi wrote:
Loaded it on an ea2700, only the 2.4ghz radio was showing. After restore to factory default the router is bricked. Request time out to pings, lan lights on, the power light does not come on.
30/30/30 does nothing.

Fractal, I know you said you have serial connected to your ea2700. Is it like the other linksys, with the square being ground, the one next to it unused, the next two for tx/Rx?
My USB to TTL serial cable is scheduled to arrive this week.


From wich firmware you upgraded to dd-wrt? I using the old style Linksys firmware but the ea2700 wont even load, i upload the trx file is says flashed succesfull afterthat it goes 4times to bootloader mode en afterthat the old Linksys firmware is back.

I think the boatloader is switching to second linux partion(some sort of failsafe)


I had the latest smart wifi or whatever they call it.

_________________
I am far from a guru, I'm barely a novice.
FlyHigh
DD-WRT User


Joined: 09 Aug 2011
Posts: 275

PostPosted: Tue May 28, 2013 9:44    Post subject: Reply with quote
Upgraded from 21061 to 21676 (K2.6 big) on Linksys E3000.

Works fine as wireless client bridged with 2.4GHz or 5GHz...
jrscs
DD-WRT User


Joined: 09 Aug 2010
Posts: 252

PostPosted: Tue May 28, 2013 12:20    Post subject: Reply with quote
ASUS RT-AC66U upgraded version 21592 to version 21676

RT-AC66U - primary router/gateway
2.4Ghz (NG-mixed) with 20Mhz channel width => OK
5Ghz (N) with 40Mhz channel width => OK
SSH => OK
Telnet => OK
Port Forward => OK
WOL over the Internet => OK
USB storage mount to JFFS => OK
PPTP server => Ok
NoCatSplash => OK

Upgraded (dd-wrt.v24-21402_NEWD-2_K2.6_std_usb_nas-nv60k.bin)
to (dd-wrt.v24-21676_NEWD-2_K2.6_std_usb_nas-nv60k.bin)


e4200 - primary router/gateway
2.4Ghz (NG-mixed) with 20Mhz channel width => OK
5Ghz (N) with 40Mhz channel width => OK
SSH => OK
Telnet => OK
Port Forward => OK
WOL over the Internet => OK
PPTP server => Ok

e2000 - hard wired from rt-ac66u
5Ghz (N) with 40Mhz channel width => OK

e3000 – Repeater Bridge on 5 Ghz (N) with 40Mhz channel width to e2000
2.4 (NG-mixed) with 20Mhz channel width => OK
5Ghz (N) with 40Mhz channel width => OK

rt-ac66u--------e2000--> repeater bridge <--e3000

note: some disconnects between e2000 and e3000

_________________
Asus AC87U A1 - DD-WRT v3.0-r43217 std (05/22/20)
Repeater Bridges(s)
Asus AC68R A1 - DD-WRT v3.0-r43217 std (05/22/20)
Netgear R6400 V2 - DD-WRT v3.0-r43136 std (05/13/20)
Asus AC66U A1 - DD-WRT v3.0-r43136 giga (05/13/20)
cyber062
DD-WRT Novice


Joined: 14 Apr 2012
Posts: 17

PostPosted: Tue May 28, 2013 16:13    Post subject: Reply with quote
E3200
dd-wrt.v24-21676_NEWD-2_K2.6_mini-e3200.bin

PPTP => Working
5ghz => No found
2.4 ghz with 40mhz (upper + manuel channel) => Working
DDNS => Working

Bug : The router (mode: DHCP server) can't distribued a ip on the network if you change the subnet mask.

_________________
Last builds:


ftp://ftp.dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/
ftp://ftp.barryware.net/Fractal%20Builds/DD-WRT-BINS/ or ftp://ftp.basmaf.com
stalonge
DD-WRT Guru


Joined: 21 Jul 2006
Posts: 1865
Location: Fortaleza Ce Brazil

PostPosted: Tue May 28, 2013 16:24    Post subject: Reply with quote
@ BS

After 24 hours running 21676 K3 in my E3000 , Samba share , PPPoe and NAS OK ...

I think for DD-wrt K3 becomes a champ , just take a look in WIFI speed ... i cant get more than 150 Mb in both 2.4 & 5 Ghz .

Thanks

Very Happy Very Happy

_________________
DDwrt ...it rocks ....
1 R8500 41556 AP OpenVPN webserver RETIRED (bricked)
1 R7800 42912 AP Wireguard webserver JFFS SAMBA FTP usb HD Mesh
1 R7800 42912 Cli Mesh
1 WZR1750 42908 AP Webserver OpenVPN
1 DDx86 Vmware 40260
1 E3000 41027 K3 @500 WAP wifi client
madman999
DD-WRT Guru


Joined: 11 Jun 2012
Posts: 1038

PostPosted: Tue May 28, 2013 20:11    Post subject: Reply with quote
does this K3 version support USB hard drives of greater than 2 TB?
_________________
Please state what make and model router plus the build number and type of DD-WRT you are using. Screen prints and a network diagram can are also helpful. Before you create a new post, use the search function. Chances are your issue has happened to someone else.

Common F.A.Q.
Where can I get the latest test Firmware or older ones?
ftp://ftp.dd-wrt.com/betas/
http://www.desipro.de/ddwrt-ren/

Asus RT-N16 on 2.6 Kong 22000M with OTRW2
Asus RT-AC66R on 3.x 28072 Giga
TP-Link Archer C9 on 3.x 28493 STD
tatsuya46
DD-WRT Guru


Joined: 03 Jan 2010
Posts: 7373
Location: YWG, Canada

PostPosted: Tue May 28, 2013 21:10    Post subject: Reply with quote
E3000 client/repeater mode still broken as usual, broken in k2.6 & k3.9.

Interesting to the best of my knowledge, i was last told they blamed the broadcom driver for it, yet tomato has/had the same driver version, working just fine..

Also with k3.9 it says my e3000 has 64kb nvram now instead of the usual 60kb, that accurate? For some reason i always thought broadcom units or at least "older" ones aka non ac, only had 60kb & it was atheros that always had 64?

_________________
LATEST FIRMWARE(S)

BrainSlayer wrote:
we just do it since we do not like any restrictions enforced by stupid cocaine snorting managers

[x86_64] Haswell i3-4150/QCA9984/QCA9882 ----> DD-WRT v3.0-r44583 std
[QUALCOMM] DIR-862L ------------------------------> DD-WRT v3.0-r44586 std
[QUALCOMM] WNDR4300 v1 ------------------------> DD-WRT v3.0-r44586 std
[QUALCOMM] DIR-862L ------------------------------> DD-WRT v3.0-r44586 std
▲ ACTIVE / INACTIVE ▼
[BROADCOM] DIR-860L A1 --------------------------> DD-WRT v3.0-r44583 std


If you use DSLReports please enable hi-res bufferbloat.


Sigh.. why do i exist anyway..
Goto page 1, 2, 3, 4, 5, 6  Next Display posts from previous:    Page 1 of 6
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum