CDM530AM dd-wrt flashen

Post new topic   Reply to topic    DD-WRT Forum Index -> Ralink SoC basierte Hardware
Author Message
middey
DD-WRT Novice


Joined: 20 Dec 2012
Posts: 3

PostPosted: Thu Dec 20, 2012 15:49    Post subject: CDM530AM dd-wrt flashen Reply with quote
Hallo zusammen,
der CDM530AM ist auch noch unter ein paar anderen namen bekannt:
    4G-Systems XsBox Move
    Zoom 4506 3G
    Zalip CDM530AM
    Aluratek CDM530AM
    AMIT CDM530AM
    Dlink DWR-131
    TRENDnet TEW-655BR3G

Ich habe die 4G-Systems XsBox Move mit folgenden Daten
    FCC ID 'PBLCDM530AM'
    CPU: Ralink RT3050F
    Flash: EON EN29LV320A 32MB
    SDRAM: EtronTech EM63A165TS 16MB


Mir ist es gelungen Telnet Zugriff auf die Box zu bekommen, indem ich die Box mit gedrücktem Reset Schalter einschalte und am RS232 Port mitlausche.
Nur dann öffnet sich eine Telnet Verbindung.

Ich liste hier mal die Befehle auf die ich herausgefunden habe:

    help
    Quote:

    command list...
    reboot
    info
    load <adr>
    go <adr>
    dm <adr>
    wm <adr>
    rm <adr>
    copy <src> <dst> <size>
    ip [ip]
    mac [mac]
    ping <ip>
    areacode


    dm
    Quote:
    DUMP 0x0-0xffffffff [0x0]


    wm
    Quote:
    wm <addr> <val>


    rm
    Quote:
    rm <addr>


    info
    Quote:
    MODEL_NAME: XSBoxMOVE
    ROMID: FOG6E2101001
    ECN_NO: 200911230001
    FMID: 6E21
    PV: 1
    IP: 192.168.123.254
    BEID: 00:50:18:5F:21:33
    PSEC: BF3FE000


    load
    Quote:
    load addr 0


    copy
    Quote:
    copy <src> <dst> <size>


    ip
    Quote:
    IP 192.168.123.254


    mac
    Quote:
    BEID 00:50:18:5F:21:33


    areacode
    Quote:
    areacode: 1


    Ich hatte eigentlich vor als erstes den gesamten Flash auszulesen aber ich komme mit dem dm Kommando einfach nicht zurecht.
    Falls das Glückt will ich dd-wrt zu flashen.
    Villeicht könnt ihr mir ja weiterhelfen.

    Mfg middey
Sponsor
middey
DD-WRT Novice


Joined: 20 Dec 2012
Posts: 3

PostPosted: Wed Feb 27, 2013 19:08    Post subject: Reply with quote
Ich habe hier mal den dmesg output für euch.
Villeicht kann mir ja einer damit weiterhelfen.

Quote:
Linux version 2.6.21 (wuming@uranus) (gcc version 3.4.2) #2 Thu Nov 12 14:28:37 CST 2009

The CPU feqenuce set to 320 MHz
CPU revision is: 0001964c
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
On node 0 totalpages: 8192
DMA zone: 64 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 8128 pages, LIFO batch:0
Normal zone: 0 pages used for memmap
Built 1 zonelists. Total pages: 8128
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock3
Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, linesize 32 bytes.
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
cause = a0800004, status = 1100ff00
PID hash table entries: 128 (order: 7, 512 bytes)
calculating r4koff... 00138800(1280000)
CPU frequency 320.00 MHz
Using 160.000 MHz high precision timer.
Console: colour dummy device 80x25
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 29264k/32768k available (2415k kernel code, 3504k reserved, 564k data, 124k init, 0k highmem)
Calibrating delay loop... 212.99 BogoMIPS (lpj=425984)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
fuse init (API version 7.8)
io scheduler noop registered (default)
FLASH_API: MAN_ID=7F DEV_ID=22F6 SIZE=4MB

------------------GPIO--------------------------
GPIOMODE:2df
Ralink gpio driver initialized
HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
N_HDLC line discipline registered.
Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
loop: loaded (max 8 devices)
rdm_major = 254
GDMA1_MAC_ADRH -- : 0x00000000
GDMA1_MAC_ADRL -- : 0x00000000
Ralink APSoC Ethernet Driver Initilization. v1.60 256 rx/tx descriptors allocated, mtu = 1500!
GDMA1_MAC_ADRH -- : 0x00009bb5
GDMA1_MAC_ADRL -- : 0x083de314
PROC INIT OK!
TX100 AD/DA current bias: 7054
TX100 slew rate control: 0038
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
ralink flash device: 0x400000 at 0xbf000000
Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
Ralink SoC physically mapped flash: Swapping erase regions for broken CFI table.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 6 MTD partitions on "Ralink SoC physically mapped flash":
0x00000000-0x00400000 : "Whole"
0x00000000-0x00010000 : "Bootloader"
0x00010000-0x00110000 : "Kernel"
0x00110000-0x003a0000 : "RootFS"
0x003a0000-0x003f0000 : "UI"
0x003f0000-0x00400000 : "Config"
block2mtd: version $Revision: 1.1.1.1 $
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
u32 classifier
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (256 buckets, 2048 max)
Register conntrack protocol helper for ESP...
GRE over IPv4 tunneling driver
Init IP_nat_proto_esp register.
ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 124k freed
Algorithmics/MIPS FPU Emulator v1.5

phy_tx_ring = 0x01c65000, tx_ring = 0xa1c65000, size: 16 bytes

phy_rx_ring = 0x01c66000, rx_ring = 0xa1c66000, size: 16 bytes
RT305x_ESW: Link Status Changed
GDMA1_FWD_CFG = 710000
dwc_otg: version 2.72a 24-JUN-2008
DWC_otg: Core Release: 2.66a
DWC_otg: Periodic Transfer Interrupt Enhancement - disabled
DWC_otg: Multiprocessor Interrupt Enhancement - disabled
DWC_otg: Using DMA mode
DWC_otg: Device using Buffer DMA mode
dwc_otg lm0: DWC OTG Controller
dwc_otg lm0: new USB bus registered, assigned bus number 1
dwc_otg lm0: irq 18, io mem 0x00000000
DWC_otg: Init: Port Power? op_state=1
DWC_otg: Init: Power Port (0)
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Load RT2880 Timer Module(Wdg/Soft)
ipt_webstr: module license 'unspecified' taints kernel.
eth2.2: Setting MAC address to 00 50 18 5f 21 34.
device eth2 entered promiscuous mode
VLAN (eth2.2): Setting underlying device (eth2) to promiscious mode.
eth2.2: add 01:00:5e:00:00:01 mcast address to master interface
eth2.2: dev_set_promiscuity(master, 1)
device eth2.2 entered promiscuous mode
br0: port 1(eth2.2) entering learning state
br0: topology change detected, propagating
br0: port 1(eth2.2) entering forwarding state
Jack 2860 version : 2.0.0.0 (Nov 12 2009)


=== pAd = c0446000, size = 402944 ===

RTMPAllocAdapterBlock, Status=0
Length of MAC:6
mac:0:50:18:5f:21:34:
----
RX DESC a1f9d000 size = 2048
RTMPAllocTxRxRingMemory, Status=0
1. Phy Mode = 9
2. Phy Mode = 9
3. Phy Mode = 9
MCS Set = ff 00 00 00 01
Main bssid = 00:50:18:5f:21:34
The UUID Hex string is:2880288028801880a8800050185f2134
The UUID ASCII string is:28802880-2880-1880-a880-0050185f2134!
== RTMPInitialize, Status=0
0x1300 = 00064380
device ra0 entered promiscuous mode
br0: port 2(ra0) entering learning state
br0: topology change detected, propagating
br0: port 2(ra0) entering forwarding state
Rcv Wcid(1) AddBAReq
Start Seq = 00000355
Rcv Wcid(1) AddBAReq
Start Seq = 00000005
RT305x_ESW: Link Status Changed


Mfg middey
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Index -> Ralink SoC basierte Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum