DD-WRT on Belkin F5D8235-4 v2 (N+)

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Ralink SoC based Hardware
Goto page Previous  1, 2, 3 ... 20, 21, 22 ... 26, 27, 28  Next
Author Message
EchoKev
DD-WRT Novice


Joined: 29 May 2012
Posts: 1

PostPosted: Tue May 29, 2012 16:23    Post subject: Reply with quote
I used the files here: ftp://dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/2012/03-19-12-r18777/Belkin-F5D8235-4_v2/

And was able to flash it correctly. It seems to work properly, except for WPA2 Enterprise authentication. It is suppose to authenticate back to a radius server. It worked once, but it has not worked since. Any idea as to how to get it to work? I am not seeing it connecting to the radius server on the back end...
Sponsor
matthewKER
DD-WRT Novice


Joined: 17 Feb 2012
Posts: 4

PostPosted: Fri Jun 08, 2012 17:23    Post subject: PPPoE Reply with quote
Have anyone tried the new builds? Can I restart the router with PPPoE in these builds?
Unfortunately, I can't try them now...
j_saade25
DD-WRT Novice


Joined: 08 Nov 2011
Posts: 5

PostPosted: Fri Jun 08, 2012 17:43    Post subject: Reply with quote
I would like to share my experience:

I am using the 18777 build as an access point and print server. I got about 20% more bandwidth on Wireless compared to Belkin's stock firmware. I have been using it for a week and I have no problems. Only LEDs don't function correctly: On a reboot, you'd get 2 purple LEDs but that's OK, no harm.

From what I know, PPPoE is still not working on pre-SP2 builds. I tried it with the same build on my main router (DIR-300's specific build). I prefer if you'd wait for a stable version.
matthewKER
DD-WRT Novice


Joined: 17 Feb 2012
Posts: 4

PostPosted: Fri Jun 08, 2012 18:00    Post subject: New builds? Reply with quote
Have you also tried new builds (6th June and 8th June)? The PPPoE in build 18777 doesn't work for me, too.
j_saade25
DD-WRT Novice


Joined: 08 Nov 2011
Posts: 5

PostPosted: Fri Jun 08, 2012 19:13    Post subject: Reply with quote
I didn't know they existed yet. Very Happy But I am not likely to test them because my main router is working fine and I'm only waiting for the next stable version.

I hope someone can help you.
Simba7
DD-WRT Novice


Joined: 09 Oct 2007
Posts: 49

PostPosted: Fri Jun 29, 2012 6:04    Post subject: Reply with quote
I just wanted to say Thanks for the firmware. My bro-in-law has this router and it could barely handle 2 xbox 360s and a laptop. Now it can handle 4 360's and 3 laptops without issues and it runs great.

Still curious on why the lights are now purple..
INLinuxdude
DD-WRT Novice


Joined: 30 Jun 2012
Posts: 1

PostPosted: Sat Jun 30, 2012 2:14    Post subject: Reply with quote
Hambone68 wrote:
Does anyone know if the newest build supports the 8366SR chipset yet? Has anyone tried it?


Anyone know of any progress on the SR chipset? I found this post http://svn.dd-wrt.com/ticket/1997 from sixteen months ago that made it sound easy... Wish I was a coding expert... Wink
Iomega0318
DD-WRT Novice


Joined: 21 Jun 2012
Posts: 5

PostPosted: Sat Jun 30, 2012 18:13    Post subject: Reply with quote
LOM wrote:
tftp-hpa is not the easiest tftp server to set up, one has to edit config and scripts file first.
There is from what I can see no linux gui based tftp servers like tftpd32 for windows.

Here is a revert file which should work, unpack the binary from the rar archive and upload it via wireless to dd-wrt firmware upgrade gui page.

Can this be used to revert the F5D8235-4 v3?
I am having issues with DD-WRT dropping out on my router and need to revert it.. if not can you possibly create one for it? I've uploaded the original F5D8235-4 v3 firmware..
Psynanni
DD-WRT Novice


Joined: 02 Jul 2012
Posts: 2

PostPosted: Mon Jul 02, 2012 18:53    Post subject: Client or Repeating Bridge Issues Reply with quote
I have recently flashed my Belkin F5D8235-4 v2 (N+) from the firmware posted on page 4 to r16785.

Unfortunately, with both firmware's I have been unable to set it up as a Client, Repeater, or Client/Repeater Bridge.

I've tried every variation listed in the wiki without any successful connections.

Has anybody been able to successfully do so (with this router specifically)?

I have had nothing but headaches with this router honestly and am ready to go Office Space on it.

(Edit: Just noticed that there is not a Client Bridge mode available...?)
bo33b
DD-WRT Novice


Joined: 05 Jan 2007
Posts: 36

PostPosted: Sun Jul 08, 2012 12:22    Post subject: Re: Client or Repeating Bridge Issues Reply with quote
Psynanni wrote:
I have recently flashed my Belkin F5D8235-4 v2 (N+) from the firmware posted on page 4 to r16785.


There are much more recent builds available: ftp://dd-wrt.com/others/eko/BrainSlayer-V24-preSP2/2012/ (open the most recent folder and find the router)

The best way to configure the non-AP mode is to go here: http://192.168.1.1/Site_Survey.asp and click "join" for the desired SSID. Also, someone mentioned that since there is no client bridge mode, you need to use Repeater bridge and just disable SSID broadcast. I haven't tried it myself with this model yet.

However I've encountered some troubles of my own running the latest 06-08-12-r19342 on my Belkin F5D8235-4_v2 -- terrible range (max 10 meters) and it won't negotiate 300Mbps with a 300Mbps N+ laptop sitting right next to it, only gets 150M. Has anyone gotten 300M out of this thing on DD-WRT? What operating distances are you achieving? Just wondering.

_________________
Wink
rtrombetta
DD-WRT Novice


Joined: 06 Aug 2012
Posts: 14

PostPosted: Thu Aug 16, 2012 19:04    Post subject: MPPE support in BrainSlayer r1951 Reply with quote
Hi!
Anybody that is using the BrainSlayer r19519 is having problem to use pptpd or pptp client ? I think that mppe support is missing.

Quote:
root@gw01:~# dmesg
<5>Linux version 3.2.23-svn19518 (root@dd-wrt) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1372 Fri Jul 20 13:31:23 CEST 2012
<7>prom: fw_arg0=00000001, fw_arg1=01f4ffb0, fw_arg2=01f503b0, fw_arg3=00000000
<7>argv[0]= (null) is invalid, skipping
<7>env[0]: memsize=32
<7>env[1]: initrd_start=0x00000000
<7>env[2]: initrd_size=0x0
<7>env[3]: flash_start=0xBF000000
<7>env[4]: flash_size=0x800000
<7>env[0]: memsize=32
<7>env[1]: initrd_start=0x00000000
<7>env[2]: initrd_size=0x0
<7>env[3]: flash_start=0xBF000000
<7>env[4]: flash_size=0x800000
<6>bootconsole [early0] enabled
<6>CPU revision is: 0001964c (MIPS 24KEc)
<6>Ralink RT3052 id:1 rev:2 running at 384.00 MHz
<6>Determined physical RAM map:
<6> memory: 02000000 @ 00000000 (usable)
<4>Zone PFN ranges:
<4> Normal 0x00000000 -> 0x00002000
<4>Movable zone start PFN for each node
<4>early_node_map[1] active PFN ranges
<4> 0: 0x00000000 -> 0x00002000
<7>On node 0 totalpages: 8192
<7>free_area_init_node: node 0, pgdat 802b1430, node_mem_map 81000000
<7> Normal zone: 64 pages used for memmap
<7> Normal zone: 0 pages reserved
<7> Normal zone: 8128 pages, LIFO batch:0
<7>pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
<7>pcpu-alloc: [0] 0
<4>Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
<5>Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock4 rootfstype=squashfs noinitrd
<6>PID hash table entries: 128 (order: -3, 512 bytes)
<6>Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
<6>Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
<4>Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
<4>Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
<6>Writing ErrCtl register=00000000
<6>Readback ErrCtl register=00000000
<6>Memory: 29252k/32768k available (2349k kernel code, 3516k reserved, 409k data, 164k init, 0k highmem)
<6>NR_IRQS:48
<6>console [ttyS1] enabled, bootconsole disabled
<6>Calibrating delay loop... 255.59 BogoMIPS (lpj=1277952)
<6>pid_max: default: 32768 minimum: 301
<6>Mount-cache hash table entries: 512
<6>NET: Registered protocol family 16
<6>bio: create slab <bio-0> at 0
<5>SCSI subsystem initialized
<6>Switching to clocksource MIPS
<6>NET: Registered protocol family 2
<6>IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
<6>TCP established hash table entries: 1024 (order: 1, 8192 bytes)
<6>TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
<6>TCP: Hash tables configured (established 1024 bind 1024)
<6>TCP reno registered
<6>UDP hash table entries: 256 (order: 0, 4096 bytes)
<6>UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
<6>NET: Registered protocol family 1
<6>squashfs: version 3.0 (2006/03/15) Phillip Lougher
<6>msgmni has been set to 57
<6>io scheduler noop registered
<6>io scheduler deadline registered (default)
<6>Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
<6>serial8250: ttyS0 at MMIO 0x10000500 (irq = 13) is a 16550A
<6>serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
<4>Ralink gpio driver initialized
<6>system type: RT3052
<6>boot type: 0
<5>ralink flash device: 0x1000000 at 0xbf000000
<6>Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
<7>Ralink SoC physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
<6>Amd/Fujitsu Extended Query Table at 0x0040
<6> Amd/Fujitsu Extended Query version 1.1.
<5>number of CFI chips: 1
<0>
<0>found squashfs at 145000
<5>Creating 6 MTD partitions on "Ralink SoC physically mapped flash":
<5>0x000000000000-0x000000030000 : "uboot"
<5>0x000000030000-0x000000040000 : "uboot-config"
<5>0x000000040000-0x000000050000 : "factory-defaults"
<5>0x000000050000-0x0000007f0000 : "linux"
<5>0x000000145000-0x0000007f0000 : "rootfs"
<4>mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
<5>0x0000007f0000-0x000000800000 : "nvram"
<6>tun: Universal TUN/TAP device driver, 1.6
<6>tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
<6>PPP generic driver version 2.4.2
<6>PPP BSD Compression module registered
<6>PPP Deflate Compression module registered
<6>NET: Registered protocol family 24
<6>Ralink APSoC Hardware Watchdog Timer
<6>u32 classifier
<6> Performance counters on
<6> Actions configured
<6>Netfilter messages via NETLINK v0.30.
<6>nf_conntrack version 0.5.0 (457 buckets, 1828 max)
<6>ctnetlink v0.93: registering with nfnetlink.
<6>IPv4 over IPv4 tunneling driver
<6>ip_tables: (C) 2000-2006 Netfilter Core Team
<6>IPP2P v0.8.2 loading
<6>ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
<6>TCP bic registered
<6>TCP cubic registered
<6>TCP westwood registered
<6>TCP highspeed registered
<6>TCP hybla registered
<6>TCP htcp registered
<6>TCP vegas registered
<6>TCP scalable registered
<6>NET: Registered protocol family 17
<5>Bridge firewalling registered
<6>8021q: 802.1Q VLAN Support v1.8
<6>searching for nvram
<6>nvram size = 0
<0>initialize Realtek VLAN config
<0>0 smi_init check[0x0509]=0x5937
<4>MAC_ADRH -- : 0x00000000
<4>MAC_ADRL -- : 0x00000000
<4>Ralink APSoC Ethernet Driver Initilization. v2.0 256 rx/tx descriptors allocated, mtu = 1500!
<4>NAPI enable, Tx Ring = 256, Rx Ring = 256
<4>MAC_ADRH -- : 0x0000000c
<4>MAC_ADRL -- : 0x43305277
<4>rt3052 access driver initialization.
<6>VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
<6>Freeing unused kernel memory: 164k freed
<4>rt2860v2_ap: module license 'unspecified' taints kernel.
<4>Disabling lock debugging due to kernel taint
<4>MAC_ADRH -- : 0x00000022
<4>MAC_ADRL -- : 0x75b55dfc
<4>
<4>phy_tx_ring = 0x01572000, tx_ring = 0xa1572000
<4>
<4>phy_rx_ring0 = 0x01573000, rx_ring0 = 0xa1573000
<4>RT305x_ESW: Link Status Changed
<4>CDMA_CSG_CFG = 81000007
<4>GDMA1_FWD_CFG = 710000
<6>using kernel STP
<6>device vlan1 entered promiscuous mode
<6>device eth2 entered promiscuous mode
<6>br0: port 1(vlan1) entering listening state
<6>br0: port 1(vlan1) entering listening state
<4>RtmpOSNetDevDetach(): RtmpOSNetDeviceDetach(), dev->name=ra0!
<4>0x1300 = 00064380
<4>0x1300 = 00064380
<6>device ra0 entered promiscuous mode
<6>br0: port 2(ra0) entering listening state
<6>br0: port 2(ra0) entering listening state
<6>br0: port 1(vlan1) entering learning state
<6>device vlan2 entered promiscuous mode
<6>device vlan2 left promiscuous mode
<6>br0: port 2(ra0) entering learning state
<6>br0: topology change detected, propagating
<6>br0: port 1(vlan1) entering forwarding state
<6>etherip: Ethernet over IPv4 tunneling driver
<6>br0: topology change detected, propagating
<6>br0: port 2(ra0) entering forwarding state
<4>nf_conntrack_pptp: Unknown symbol nf_ct_gre_keymap_destroy (err 0)
<4>nf_conntrack_pptp: Unknown symbol nf_ct_gre_keymap_flush (err 0)
<4>nf_conntrack_pptp: Unknown symbol nf_ct_gre_keymap_add (err 0)
<6>IMQ driver loaded successfully. (numdevs = 2, numqueues = 1)
<6> Hooking IMQ before NAT on PREROUTING.
<6> Hooking IMQ after NAT on POSTROUTING.
<6>Ebtables v2.0 registered
<6>IMQ driver unloaded successfully.
<6>Ebtables v2.0 unregistered
<6>IMQ driver loaded successfully. (numdevs = 2, numqueues = 1)
<6> Hooking IMQ before NAT on PREROUTING.
<6> Hooking IMQ after NAT on POSTROUTING.
<6>Ebtables v2.0 registered
Agnostic.Otter
DD-WRT Novice


Joined: 21 Jul 2012
Posts: 1

PostPosted: Wed Aug 29, 2012 19:50    Post subject: Astrill VPN Reply with quote
Has anyone tried to connect to Astrill VPN servers?

I have tried several builds (18xxx and 19xxx) with no luck. It never connects.

Cheers,

A.
rtrombetta
DD-WRT Novice


Joined: 06 Aug 2012
Posts: 14

PostPosted: Sat Sep 01, 2012 11:00    Post subject: Re: Astrill VPN Reply with quote
Agnostic.Otter wrote:
Has anyone tried to connect to Astrill VPN servers?

I have tried several builds (18xxx and 19xxx) with no luck. It never connects.

Cheers,

A.


I don't know Astrill VPN server, but if it has MPPE encryption enabled the ddwrt client can't connect because the mppe module is missing. Try disabling encryption on both sides just to see if it connects.
enigmas
DD-WRT Novice


Joined: 07 Sep 2012
Posts: 2

PostPosted: Fri Sep 07, 2012 17:08    Post subject: GPIO Functions: Reply with quote
I've gathered some of GPIO functions:

Tested by telnet:
gpio disable 5 #internet blue on
gpio enable 6 #internet orange off

gpio disable 6 #internet orange on
gpio enable 5 #internet blue off

gpio disable 8 #modem orange on
gpio enable 8 #modem orange off

gpio disable 11 #modem blue on
gpio enable 11 #modem blue off

gpio disable 9 #router blue on
gpio enable 9 #router blue off

#Long press resset button
gpio pool 10
pressed = 00
unpressed = 01
gpio disable 10 #factory reset

gpio enable 12 #security orange off
gpio disable 12 #security orange on

gpio enable 13 #security blue off
gpio disable 13 #security blue on

gpio enable 22 #storage orange off
gpio disable 22 #storage orange on

gpio enable 23 #storage blue off
gpio disable 23 #storage blue on

#wps button
gpio pool 0
pressed = 00
unpressed = 01

Gathered from OpenWrt:
- wired/wireless leds are controlled via bit shift register sitting on gpio pins 14 (ctl) and 4 (clk)
- speed leds are controlled via bit shift register sitting on pins 17 (ctl) and 18 (clk)

Some notes:
- restore config function doesn't work properly, the router get stucked.
- PPPoE doesn't work with preselected want port, bridge port must be selected for wan, br0
- current firmware level is more to instable to use it for a long period of time, if there will be any new releases and if the time permits I'll test them.
Anaerin
DD-WRT Novice


Joined: 17 Aug 2007
Posts: 31

PostPosted: Sat Sep 08, 2012 1:41    Post subject: Re: GPIO Functions: Reply with quote
enigmas wrote:
I've gathered some of GPIO functions:

Tested by telnet:
gpio disable 5 #internet blue on
gpio enable 6 #internet orange off

gpio disable 6 #internet orange on
gpio enable 5 #internet blue off

gpio disable 8 #modem orange on
gpio enable 8 #modem orange off

gpio disable 11 #modem blue on
gpio enable 11 #modem blue off

gpio disable 9 #router blue on
gpio enable 9 #router blue off

#Long press resset button
gpio pool 10
pressed = 00
unpressed = 01
gpio disable 10 #factory reset

gpio enable 12 #security orange off
gpio disable 12 #security orange on

gpio enable 13 #security blue off
gpio disable 13 #security blue on

gpio enable 22 #storage orange off
gpio disable 22 #storage orange on

gpio enable 23 #storage blue off
gpio disable 23 #storage blue on

#wps button
gpio pool 0
pressed = 00
unpressed = 01

Gathered from OpenWrt:
- wired/wireless leds are controlled via bit shift register sitting on gpio pins 14 (ctl) and 4 (clk)
- speed leds are controlled via bit shift register sitting on pins 17 (ctl) and 18 (clk)

Some notes:
- restore config function doesn't work properly, the router get stucked.
- PPPoE doesn't work with preselected want port, bridge port must be selected for wan, br0
- current firmware level is more to instable to use it for a long period of time, if there will be any new releases and if the time permits I'll test them.

I saw Eko post in the Broadcom thread for the v3 of this router that he has code/drivers/something available to handle bit-shift registers on GPIO ports like these.

Any chance we can get these functions enabled? Is there some config flag in NVRAM we can edit to set which GPIO does what? Can someone write a small daemon to drive the "Bandwidth" meter?
Goto page Previous  1, 2, 3 ... 20, 21, 22 ... 26, 27, 28  Next Display posts from previous:    Page 21 of 28
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Ralink SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum