DD-WRT :: View topic - TP-LINK TL-WR1043ND No Internet / WAN

TP-LINK TL-WR1043ND No Internet / WAN

DD-WRT Forum Index -> Qualcomm Atheros based Hardware

Goto page Previous 1, 2, 3 Next

View previous topic :: View next topic

Author

Message

eddyjay
DD-WRT Novice

Joined: 21 Aug 2012
Posts: 10

Posted: Thu Aug 23, 2012 8:52 Post subject:

troy1 wrote:

I've got the same problem with mine serial starts with 12xxxxxxxxx. Update goes smooth but no WAN.

V 1.8

Same here.
Tried several FWs, still no WAN
also 12xxxxxxxxx V1.8

Sponsor

checho
DD-WRT Guru

Joined: 27 Feb 2007
Posts: 527
Location: Bulgaria

Posted: Thu Aug 23, 2012 8:59 Post subject:
telnet 192.168.1.1 and then dmesg ifconfig

eddyjay
DD-WRT Novice

Joined: 21 Aug 2012
Posts: 10

Posted: Fri Aug 24, 2012 20:15 Post subject:

dmesg:

Code:

0] gpio_proc: module loaded and /proc/gpio/ created
<6>[ 0.180000] Register LED Device
<6>[ 0.180000] gpiochip_add: registered GPIOs 0 to 63 on device: ar71xx
<5>[ 0.190000] wl0gpio_proc: module loaded and /proc/wl0gpio/ created
<4>[ 0.190000] AR7100 GPIOC major 0
<6>[ 0.200000] squashfs: version 3.0 (2006/03/15) Phillip Lougher
<6>[ 0.200000] msgmni has been set to 57
<6>[ 0.210000] io scheduler noop registered
<6>[ 0.210000] io scheduler deadline registered (default)
<6>[ 0.220000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
<6>[ 0.240000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 19) is a 16550A
<6>[ 0.250000] console [ttyS0] enabled, bootconsole disabled
<0>[ 0.260000] guessed flashsize = 8M
<0>[ 0.270000] scanning for root partition
<0>[ 0.270000] tplink uboot detected
<0>[ 0.270000] bootloader size = 20000
<0>[ 0.280000]
<0>[ 0.280000] found squashfs at 100000
<5>[ 0.290000] Creating 8 MTD partitions on "ar7100-nor0":
<5>[ 0.290000] 0x000000000000-0x000000020000 : "RedBoot"
<5>[ 0.300000] 0x000000020000-0x0000007e0000 : "linux"
<5>[ 0.300000] 0x000000100000-0x0000006f0000 : "rootfs"
<5>[ 0.310000] mtd: partition "rootfs" set to be root filesystem
<5>[ 0.320000] 0x0000006f0000-0x0000007e0000 : "ddwrt"
<5>[ 0.320000] 0x0000007e0000-0x0000007f0000 : "nvram"
<5>[ 0.330000] 0x0000007f0000-0x000000800000 : "FIS directory"
<5>[ 0.340000] 0x0000007f0000-0x000000800000 : "board_config"
<5>[ 0.340000] 0x000000000000-0x000000800000 : "fullflash"
<4>[ 0.350000] ->Oops: flash id 0x10216 .
<6>[ 0.350000] tun: Universal TUN/TAP device driver, 1.6
<6>[ 0.360000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>

<4>[ 0.370000] Found an RTL8366RB switch
<5>[ 0.370000] Realtek RTL8366RB ethernet switch driver version 0.2.3
<6>[ 0.380000] rtl8366rb rtl8366rb: using GPIO pins 18 (SDA) and 19 (SCK)
<6>[ 0.380000] rtl8366rb rtl8366rb: RTL5937 ver. 3 chip found
<6>[ 0.440000] rtl8366rb: probed
<6>[ 0.640000] PPP generic driver version 2.4.2
<6>[ 0.650000] PPP BSD Compression module registered
<6>[ 0.650000] PPP Deflate Compression module registered
<6>[ 0.660000] PPP MPPE Compression module registered
<6>[ 0.660000] NET: Registered protocol family 24
<6>[ 0.670000] Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec soft_panic=0 (nowayout= 0)
<7>[ 0.680000] Registered led device: generic_0
<7>[ 0.680000] Registered led device: generic_1
<7>[ 0.680000] Registered led device: generic_2
<7>[ 0.680000] Registered led device: generic_3
<7>[ 0.680000] Registered led device: generic_4
<7>[ 0.680000] Registered led device: generic_5
<7>[ 0.680000] Registered led device: generic_6
<7>[ 0.680000] Registered led device: generic_7
<7>[ 0.680000] Registered led device: generic_8
<7>[ 0.680000] Registered led device: generic_9
<7>[ 0.680000] Registered led device: generic_10
<7>[ 0.680000] Registered led device: generic_11
<7>[ 0.680000] Registered led device: generic_12
<7>[ 0.680000] Registered led device: generic_13
<7>[ 0.680000] Registered led device: generic_14
<7>[ 0.680000] Registered led device: generic_15
<7>[ 0.680000] Registered led device: generic_16
<7>[ 0.690000] Registered led device: generic_17
<7>[ 0.690000] Registered led device: generic_21
<7>[ 0.690000] Registered led device: generic_22
<7>[ 0.690000] Registered led device: generic_23

<7>[ 0.690000] Registered led device: generic_24
<7>[ 0.690000] Registered led device: generic_25
<7>[ 0.690000] Registered led device: generic_26
<7>[ 0.690000] Registered led device: generic_27
<7>[ 0.690000] Registered led device: generic_28
<7>[ 0.690000] Registered led device: generic_29
<7>[ 0.690000] Registered led device: generic_30
<7>[ 0.690000] Registered led device: generic_31
<6>[ 0.690000] u32 classifier
<6>[ 0.690000] Performance counters on
<6>[ 0.700000] input device check on
<6>[ 0.700000] Actions configured
<6>[ 0.700000] Netfilter messages via NETLINK v0.30.
<6>[ 0.710000] nf_conntrack version 0.5.0 (460 buckets, 1840 max)
<4>[ 0.710000] nf_conntrack_rtsp v0.6.21 loading
<4>[ 0.720000] nf_nat_rtsp v0.6.21 loading
<6>[ 0.720000] ip_tables: (C) 2000-2006 Netfilter Core Team
<6>[ 0.730000] IPP2P v0.8.2 loading
<6>[ 0.730000] TCP westwood registered
<6>[ 0.730000] TCP hybla registered
<6>[ 0.740000] TCP vegas registered
<6>[ 0.740000] NET: Registered protocol family 17
<5>[ 0.750000] Bridge firewalling registered
<6>[ 0.750000] 8021q: 802.1Q VLAN Support v1.8
<6>[ 0.750000] searching for nvram
<6>[ 0.760000] nvram size = 0
<0>[ 0.790000] Broken NVRAM found, recovering it (Magic 55AA030B)
<6>[ 0.800000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
<6>[ 0.810000] Freeing unused kernel memory: 160k freed
<6>[ 3.850000] eth0: Atheros AG71xx at 0xb9000000, irq 4
<7>[ 4.260000] ar71xx: pll_reg 0xb8050014: 0x1a000000

<6>[ 4.260000] eth0: link up (1000Mbps/Full duplex)
<6>[ 4.480000] Compat-wireless backport release: compat-wireless-2012-07-16
<6>[ 4.490000] Backport based on wireless-testing.git master-2012-07-16
<6>[ 4.490000] compat.git: wireless-testing.git
<6>[ 4.670000] cfg80211: Calling CRDA to update world regulatory domain
<6>[ 5.020000] cfg80211: World regulatory domain updated:
<6>[ 5.030000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6>[ 5.030000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 5.040000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
<6>[ 5.050000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
<6>[ 5.060000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 5.070000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<7>[ 5.390000] ath: EEPROM regdomain: 0x0
<7>[ 5.390000] ath: EEPROM indicates default country code should be used
<7>[ 5.390000] ath: doing EEPROM country->regdmn map search
<7>[ 5.390000] ath: country maps to regdmn code: 0x3a
<7>[ 5.390000] ath: Country alpha2 being used: US
<7>[ 5.390000] ath: Regpair used: 0x3a
<7>[ 5.420000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
<6>[ 5.420000] ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2133 RF Rev:a2 mem=0xb80c0000, irq=2
<6>[ 5.430000] cfg80211: Calling CRDA for country: US
<6>[ 5.550000] cfg80211: Regulatory domain changed to country: US
<6>[ 5.560000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6>[ 5.570000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
<6>[ 5.570000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
<6>[ 5.580000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 5.590000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 5.600000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 5.610000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
<6>[ 8.220000] device vlan1 entered promiscuous mode
<6>[ 8.220000] device eth0 entered promiscuous mode

<6>[ 8.230000] br0: port 1(vlan1) entered forwarding state
<6>[ 8.230000] br0: port 1(vlan1) entered forwarding state
<6>[ 8.310000] cfg80211: Calling CRDA to update world regulatory domain
<6>[ 8.340000] cfg80211: World regulatory domain updated:
<6>[ 8.340000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6>[ 8.350000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 8.360000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
<6>[ 8.370000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
<6>[ 8.380000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 8.380000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 8.390000] cfg80211: Calling CRDA for country: US
<6>[ 8.410000] cfg80211: Regulatory domain changed to country: US
<6>[ 8.420000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6>[ 8.430000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
<6>[ 8.430000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
<6>[ 8.440000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 8.450000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 8.460000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 8.470000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
<6>[ 10.230000] br0: port 1(vlan1) entered forwarding state
<3>[ 12.460000] ath: phy0: Unable to set channel
<6>[ 15.720000] device ath0 entered promiscuous mode
<6>[ 15.720000] br0: port 2(ath0) entered forwarding state
<6>[ 15.730000] br0: port 2(ath0) entered forwarding state
<6>[ 16.750000] device vlan2 entered promiscuous mode
<6>[ 16.850000] device vlan2 left promiscuous mode
<6>[ 17.730000] br0: port 2(ath0) entered forwarding state
<6>[ 18.540000] etherip: Ethernet over IPv4 tunneling driver
<6>[ 425.710000] device vlan1 left promiscuous mode
<6>[ 425.710000] br0: port 1(vlan1) entered disabled state
<6>[ 425.720000] device ath0 left promiscuous mode

<6>[ 425.730000] br0: port 2(ath0) entered disabled state
<6>[ 428.340000] device vlan1 entered promiscuous mode
<6>[ 428.350000] br0: port 1(vlan1) entered forwarding state
<6>[ 428.350000] br0: port 1(vlan1) entered forwarding state
<6>[ 430.350000] br0: port 1(vlan1) entered forwarding state
<6>[ 430.850000] cfg80211: Calling CRDA to update world regulatory domain
<6>[ 430.880000] cfg80211: World regulatory domain updated:
<6>[ 430.890000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6>[ 430.890000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 430.900000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
<6>[ 430.910000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
<6>[ 430.920000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 430.930000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 430.930000] cfg80211: Calling CRDA for country: US
<6>[ 430.950000] cfg80211: Regulatory domain changed to country: US
<6>[ 430.960000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6>[ 430.970000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
<6>[ 430.980000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
<6>[ 430.980000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 430.990000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 431.000000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 431.010000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
<3>[ 434.940000] ath: phy0: Unable to set channel
<6>[ 437.800000] device ath0 entered promiscuous mode
<6>[ 437.800000] br0: port 2(ath0) entered forwarding state
<6>[ 437.810000] br0: port 2(ath0) entered forwarding state
<6>[ 439.810000] br0: port 2(ath0) entered forwarding state
<6>[ 624.660000] device vlan1 left promiscuous mode
<6>[ 624.660000] br0: port 1(vlan1) entered disabled state
<6>[ 624.670000] device ath0 left promiscuous mode
<6>[ 624.680000] br0: port 2(ath0) entered disabled state

<6>[ 627.260000] device vlan1 entered promiscuous mode
<6>[ 627.270000] br0: port 1(vlan1) entered forwarding state
<6>[ 627.270000] br0: port 1(vlan1) entered forwarding state
<6>[ 629.270000] br0: port 1(vlan1) entered forwarding state
<6>[ 629.770000] cfg80211: Calling CRDA to update world regulatory domain
<6>[ 629.800000] cfg80211: World regulatory domain updated:
<6>[ 629.810000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6>[ 629.810000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 629.820000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
<6>[ 629.830000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
<6>[ 629.840000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 629.850000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 629.850000] cfg80211: Calling CRDA for country: US
<6>[ 629.870000] cfg80211: Regulatory domain changed to country: US
<6>[ 629.880000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6>[ 629.890000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
<6>[ 629.900000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
<6>[ 629.900000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 629.910000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 629.920000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 629.930000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
<3>[ 633.860000] ath: phy0: Unable to set channel
<6>[ 636.680000] device ath0 entered promiscuous mode
<6>[ 636.980000] br0: port 2(ath0) entered forwarding state
<6>[ 636.990000] br0: port 2(ath0) entered forwarding state
<6>[ 638.990000] br0: port 2(ath0) entered forwarding state
<6>[ 789.940000] device vlan1 left promiscuous mode
<6>[ 789.950000] device eth0 left promiscuous mode
<6>[ 789.950000] br0: port 1(vlan1) entered disabled state
<6>[ 789.960000] device ath0 left promiscuous mode
<6>[ 789.970000] br0: port 2(ath0) entered disabled state

<6>[ 794.880000] device vlan1 entered promiscuous mode
<6>[ 794.880000] device eth0 entered promiscuous mode
<6>[ 794.890000] br0: port 1(vlan1) entered forwarding state
<6>[ 794.890000] br0: port 1(vlan1) entered forwarding state
<6>[ 796.890000] br0: port 1(vlan1) entered forwarding state
<6>[ 797.390000] cfg80211: Calling CRDA to update world regulatory domain
<6>[ 797.420000] cfg80211: World regulatory domain updated:
<6>[ 797.420000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6>[ 797.430000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 797.440000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
<6>[ 797.450000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
<6>[ 797.450000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 797.460000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 797.470000] cfg80211: Calling CRDA for country: US
<6>[ 797.490000] cfg80211: Regulatory domain changed to country: US
<6>[ 797.490000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
<6>[ 797.500000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
<6>[ 797.510000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
<6>[ 797.520000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 797.530000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 797.530000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
<6>[ 797.540000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
<3>[ 801.550000] ath: phy0: Unable to set channel
<6>[ 804.370000] device ath0 entered promiscuous mode
<6>[ 804.690000] br0: port 2(ath0) entered forwarding state
<6>[ 804.690000] br0: port 2(ath0) entered forwarding state
<6>[ 805.400000] device vlan2 entered promiscuous mode
<6>[ 805.450000] device vlan2 left promiscuous mode
<6>[ 806.690000] br0: port 2(ath0) entered forwarding state

ifconfig

Code:

ath0 Link encap:Ethernet HWaddr 90:F6:52:DC:2E:BC
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2402 errors:0 dropped:0 overruns:0 frame:0
TX packets:2690 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:32
RX bytes:305311 (298.1 KiB) TX bytes:886539 (865.7 KiB)

br0 Link encap:Ethernet HWaddr 90:F6:52:DC:2E:BC
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:12376 errors:0 dropped:1277 overruns:0 frame:0
TX packets:11203 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1233765 (1.1 MiB) TX bytes:8820438 (8.4 MiB)

br0:0 Link encap:Ethernet HWaddr 90:F6:52:DC:2E:BC
inet addr:169.254.255.1 Bcast:169.254.255.255 Mask:255.255.0.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1

eth0 Link encap:Ethernet HWaddr 90:F6:52:DC:2E:BC
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:7707 errors:0 dropped:0 overruns:0 frame:0
TX packets:8083 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1023497 (999.5 KiB) TX bytes:5346454 (5.0 MiB)
Interrupt:4

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MULTICAST MTU:16436 Metric:1
RX packets:7 errors:0 dropped:0 overruns:0 frame:0
TX packets:7 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:424 (424.0 B) TX bytes:424 (424.0 B)

mon.ath0 Link encap:UNSPEC HWaddr 90-F6-52-DC-2E-BC-00-00-00-00-00-00-00-00-00-00
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:4830 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:32
RX bytes:1507465 (1.4 MiB) TX bytes:0 (0.0 B)

vlan1 Link encap:Ethernet HWaddr 90:F6:52:DC:2E:BC
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:7707 errors:0 dropped:28 overruns:0 frame:0
TX packets:7935 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:884771 (864.0 KiB) TX bytes:5266170 (5.0 MiB)

vlan2 Link encap:Ethernet HWaddr 90:F6:52:DC:2E:BD
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:148 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:47952 (46.8 KiB)

eddyjay
DD-WRT Novice

Joined: 21 Aug 2012
Posts: 10

Posted: Fri Aug 24, 2012 20:32 Post subject:
I don't know if this also helps, but the network cable connected to the WAN does not light up in the modem side, meaning that probably the port is actually not working at all. If I flash back to stock, it lights up again, and I have WAN access...

troy1
DD-WRT Novice

Joined: 19 Nov 2008
Posts: 12

Posted: Sat Aug 25, 2012 16:44 Post subject:
Same with mine no WAN light. Flashed back to OEM firmware for now.

checho
DD-WRT Guru

Joined: 27 Feb 2007
Posts: 527
Location: Bulgaria

Posted: Sat Aug 25, 2012 18:25 Post subject:

I am worried that I don't see eth1 as a hardware device. Please post ifconfig -a.

Please any other user who has TL-WR1043ND post your ifconfig so that we see if eth1 has to show up or no.

I don't know if I am on a right track or not, developers must say. Regardless of that it could help if any of you may disassemble the router and post pictures of board so that it is compared to the known one. Please also post what is written on the electronics.

eddyjay
DD-WRT Novice

Joined: 21 Aug 2012
Posts: 10

Posted: Sun Aug 26, 2012 17:49 Post subject:
flashed back to stock. Going to make another flash tomorrow for the ipconfig -a Any version you reccomend? Last try was 19519

dlewando
DD-WRT Novice

Joined: 24 Aug 2012
Posts: 16
Location: germany

Posted: Sun Aug 26, 2012 17:59 Post subject: also no wan ip with sn 12xxxxxxx

yo folks,
i have the same problem. s/n: 12xxxxxxx v1.8

i'm also back on stock
here's my ifconfig -->

Code:

br0 Link encap:Ethernet HWaddr 90:F6:52:DC:16:4A
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:24947 errors:0 dropped:28 overruns:0 frame:0
TX packets:26962 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1591398 (1.5 MiB) TX bytes:16579101 (15.8 MiB)
br0:0 Link encap:Ethernet HWaddr 90:F6:52:DC:16:4A
inet addr:169.254.255.1 Bcast:169.254.255.255 Mask:255.255.0.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
eth0 Link encap:Ethernet HWaddr 90:F6:52:DC:16:4A
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:24971 errors:0 dropped:0 overruns:0 frame:0
TX packets:27026 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2042314 (1.9 MiB) TX bytes:16708341 (15.9 MiB)
Interrupt:4
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MULTICAST MTU:16436 Metric:1
RX packets:6 errors:0 dropped:0 overruns:0 frame:0
TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:348 (348.0 B) TX bytes:348 (348.0 B)
vlan1 Link encap:Ethernet HWaddr 90:F6:52:DC:16:4A
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:24971 errors:0 dropped:0 overruns:0 frame:0
TX packets:26962 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1592836 (1.5 MiB) TX bytes:16579101 (15.8 MiB)
vlan2 Link encap:Ethernet HWaddr 90:F6:52:DC:16:4B
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:64 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:21136 (20.6 KiB)

eddyjay
DD-WRT Novice

Joined: 21 Aug 2012
Posts: 10

Posted: Tue Aug 28, 2012 21:04 Post subject:
I still haven't had the time to do another flash and test. From what I saw in other forums is possibly due to the fact that The driver for the WAN is not being properly loaded. OR The bootloader is shutting down the eth1 before dd-wrt boots. OK. Departing from this, what can we, common mortals, do?

gizmo64
DD-WRT Novice

Joined: 10 Aug 2012
Posts: 2

Posted: Wed Aug 29, 2012 12:32 Post subject:

Ok guys these steps worked for me.

1. Revert back to TP-Link firmware. wr1043nv1_en_3_9_17-sysupgrade.bin

2. Flash with this German firmware wr1043nv1_de_3_9_17_up_boot(100331).bin

3. Flash with gargoyle_1……-ar71xx-tl-wr1043nd-v1-squashfs-factory.bin

Now the WAN port will work. If anybody needs a link to the wr1043nv1_de_3_9_17_up_boot(100331).bin firmware..I would be happy to upload to dropbox.

Cheers

eddyjay
DD-WRT Novice

Joined: 21 Aug 2012
Posts: 10

Posted: Wed Aug 29, 2012 12:32 Post subject:

According to this post:
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=159960

and this posts in Gargoyle: http://www.gargoyle-router.com/phpbb/viewtopic.php?f=8&t=2584

The problem is actually the bootloader in some latest 1.8 versions explained here

http://wiki.openwrt.org/toh/tp-link/tl-wr1043nd

and here

https://dev.openwrt.org/ticket/11898

So... Dear developers and helpers, what can we do?
This will keep happening from now on, and people will keep asking!

eddyjay
DD-WRT Novice

Joined: 21 Aug 2012
Posts: 10

Posted: Wed Aug 29, 2012 16:55 Post subject:

Not that I have much faith this will get us anywhere, since noone replies here, but here goes:

Code:

root@DD-WRT:~# ifconfig -a
ath0 Link encap:Ethernet HWaddr 90:F6:52:DC:2E:BC
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:554 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:32
RX bytes:0 (0.0 B) TX bytes:122898 (120.0 KiB)

br0 Link encap:Ethernet HWaddr 90:F6:52:DC:2E:BC
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1321 errors:0 dropped:169 overruns:0 frame:0
TX packets:901 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:183530 (179.2 KiB) TX bytes:830861 (811.3 KiB)

br0:0 Link encap:Ethernet HWaddr 90:F6:52:DC:2E:BC
inet addr:169.254.255.1 Bcast:169.254.255.255 Mask:255.255.0.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1

eth0 Link encap:Ethernet HWaddr 90:F6:52:DC:2E:BC
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1442 errors:0 dropped:0 overruns:0 frame:0
TX packets:910 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:226317 (221.0 KiB) TX bytes:837417 (817.7 KiB)
Interrupt:4

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MULTICAST MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

mon.ath0 Link encap:UNSPEC HWaddr 90-F6-52-DC-2E-BC-00-00-00-00-00-00-00-00-00-00
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1294 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:32
RX bytes:141646 (138.3 KiB) TX bytes:0 (0.0 B)

vlan1 Link encap:Ethernet HWaddr 90:F6:52:DC:2E:BC
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1442 errors:0 dropped:12 overruns:0 frame:0
TX packets:901 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:200361 (195.6 KiB) TX bytes:830861 (811.3 KiB)

vlan2 Link encap:Ethernet HWaddr 90:F6:52:DC:2E:BD
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:9 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:2916 (2.8 KiB)

So... What next?

eddyjay
DD-WRT Novice

Joined: 21 Aug 2012
Posts: 10

Posted: Wed Aug 29, 2012 18:13 Post subject:

OK People... I solved it!!!!!

Following the advice from Gizmo64

Here's what I did:

1) Flashed back to stock using the bin provided here:
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=85237&postdays=0&postorder=asc&start=8

2) Flashed German Version of the original stock downloadable at:
http://narod.ru/disk/37622290001/wr1043nv1_de_3_9_17_up_boot(100331).bin.html

3) Flashed dd-wrt version 18777

Now WAN is working and this post is being made through it

gizmo64
DD-WRT Novice

Joined: 10 Aug 2012
Posts: 2

Posted: Thu Aug 30, 2012 1:18 Post subject:
Here is another link to the German firmware. https://dl.dropbox.com/u/12200022/wr1043nv1_de_3_9_17_up_boot%28100331%29.bin.zip

ayharano
DD-WRT Novice

Joined: 10 Oct 2008
Posts: 1

Posted: Thu Aug 30, 2012 14:26 Post subject:

Now WAN port is working with build 18777, however I couldn't use WAN as a DHCP client.

I cloned my PC configs to be able to connect to Internet, but it really seems a workaround.

Anyone has any idea how to make it work?

Thanks in advance.

Edit: Here is the output of 'ifconfig -a'

root@DD-WRT:~# ifconfig -a
ath0 Link encap:Ethernet HWaddr AA:BB:CC:DD:EE:FF
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:173121 errors:0 dropped:0 overruns:0 frame:0
TX packets:116106 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:32
RX bytes:211909827 (202.0 MiB) TX bytes:40903068 (39.0 MiB)

br0 Link encap:Ethernet HWaddr AA:BB:CC:DD:EE:FF
inet addr:10.20.30.1 Bcast:10.20.30.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:269781 errors:0 dropped:108 overruns:0 frame:0
TX packets:302799 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:215117866 (205.1 MiB) TX bytes:309519206 (295.1 MiB)

br0:0 Link encap:Ethernet HWaddr AA:BB:CC:DD:EE:FF
inet addr:169.254.255.1 Bcast:169.254.255.255 Mask:255.255.0.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1

eth0 Link encap:Ethernet HWaddr AA:BB:CC:DD:EE:FF
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:364908 errors:0 dropped:0 overruns:0 frame:0
TX packets:424043 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:303126359 (289.0 MiB) TX bytes:481316741 (459.0 MiB)
Interrupt:4

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MULTICAST MTU:16436 Metric:1
RX packets:534 errors:0 dropped:0 overruns:0 frame:0
TX packets:534 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:39330 (38.4 KiB) TX bytes:39330 (38.4 KiB)

mon.ath0 Link encap:UNSPEC HWaddr 90-F6-52-C8-4A-2A-00-00-00-00-00-00-00-00-00-00
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1563 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:32
RX bytes:136272 (133.0 KiB) TX bytes:0 (0.0 B)

vlan1 Link encap:Ethernet HWaddr AA:BB:CC:DD:EE:FF
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:89846 errors:0 dropped:0 overruns:0 frame:0
TX packets:183701 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:5042335 (4.8 MiB) TX bytes:263808021 (251.5 MiB)

vlan2 Link encap:Ethernet HWaddr AA:BB:CC:DD:EE:FF
inet addr:201.XXX.YYY.ZZZ Bcast:201.XXX.YYY.255 Mask:255.255.240.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:275062 errors:0 dropped:0 overruns:0 frame:0
TX packets:240342 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:291515680 (278.0 MiB) TX bytes:215812548 (205.8 MiB)

Goto page Previous 1, 2, 3 Next

Display posts from previous:

Page 2 of 3

DD-WRT Forum Index -> Qualcomm Atheros based Hardware

All times are GMT

Navigation

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum

Log in

TP-LINK TL-WR1043ND No Internet / WAN

Quick Links

Log in