Posted: Sat Dec 17, 2011 15:41 Post subject: WNR3500Lv2
I've been looking around on the internet for a good couple of hours now for ways to flash this router but I've been unsuccessful in finding a .chk file that supports v2 which has 128MiB NAND instead of 64MiB serial flash.
(note that I'm talking about 3500L v2 and not 3500 v2)
There seems to be a few other differences between v1 and v2 like another cpu which is BCM5357.
Here's some information about the router when i telnet into it:
Code:
# cat /proc/version
Linux version 2.6.22 (zacker@STB-Linux) (gcc version 4.2.3) #1 Fri Jul 22 15:08:13 SGT 2011
# cat /proc/cpuinfo
system type : Broadcom BCM5357 chip rev 2
processor : 0
cpu model : MIPS 74K V4.9
BogoMIPS : 239.20
wait instruction : no
microsecond timers : yes
tlb_entries : 64
extra interrupt vector : no
hardware watchpoint : yes
ASEs implemented : mips16 dsp
VCED exceptions : not available
VCEI exceptions : not available
unaligned_instructions : 34
dcache hits : 2147483648
dcache misses : 2466240976
icache hits : 2147483648
icache misses : 1870356182
instructions : 2147483648
# cat /proc/meminfo
MemTotal: 125916 kB
MemFree: 82672 kB
Buffers: 6300 kB
Cached: 16588 kB
SwapCached: 0 kB
Active: 10276 kB
Inactive: 17688 kB
HighTotal: 0 kB
HighFree: 0 kB
LowTotal: 125916 kB
LowFree: 82672 kB
SwapTotal: 0 kB
SwapFree: 0 kB
Dirty: 0 kB
Writeback: 0 kB
AnonPages: 5088 kB
Mapped: 3692 kB
Slab: 10132 kB
SReclaimable: 1896 kB
SUnreclaim: 8236 kB
PageTables: 448 kB
NFS_Unstable: 0 kB
Bounce: 0 kB
CommitLimit: 62956 kB
Committed_AS: 10232 kB
VmallocTotal: 1015800 kB
VmallocUsed: 4404 kB
VmallocChunk: 1009828 kB
# ps w
PID Uid VSZ Stat Command
1 nobody 2260 S /sbin/preinit
2 nobody SW< [kthreadd]
3 nobody SWN [ksoftirqd/0]
4 nobody SW< [events/0]
5 nobody SW< [khelper]
15 nobody SW< [kblockd/0]
37 nobody SW [pdflush]
38 nobody SW [pdflush]
39 nobody SW< [kswapd0]
40 nobody SW< [aio/0]
574 nobody SW< [mtdblockd]
1901 nobody 1896 S upnp -D -W eth0
1906 nobody 1492 S /bin/eapd
1909 nobody 1940 S nas
1913 nobody 2916 S /bin/wps_monitor
1960 nobody 1704 S swresetd
1962 nobody 1520 S dnsRedirectReplyd
1967 nobody 872 S dnsmasq -h -n -c 0 -N -i br0 -r /tmp/resolv.conf -u root
1970 nobody 844 S udhcpd /tmp/udhcpd.conf
1973 nobody 1520 S ddnsd &
1979 nobody 1816 S heartbeat
1982 nobody 7744 S httpd -S -E /usr/sbin/ca.pem /usr/sbin/httpsd.pem
1985 nobody 1480 S wlanconfigd
1990 nobody 1528 S pot run
2003 nobody 1524 S scheact
2012 nobody 2532 S upnpd
2016 nobody 1916 S /usr/sbin/email
2026 nobody 1620 S lld2d br0
2028 nobody 2160 S /usr/sbin/acl_logd
2036 nobody 2028 S check_fw
2082 nobody SW< [khubd]
2131 nobody 820 S udhcpc -i eth0 -p /var/run/udhcpc0.pid -s /tmp/udhcpc -H WNR3500Lv2
2168 nobody 1512 S wpsd
2217 nobody 1064 R telnetd
2218 nobody 1060 S /bin/sh
2252 nobody 1516 S /usr/sbin/timesync /sbin/ntpclient
2258 nobody SW< [scsi_eh_0]
2259 nobody SW< [usb-storage]
2318 nobody 3120 S /usr/local/samba/nmbd -D
2319 nobody 5396 S /usr/local/samba/smbd -D
2320 nobody 5396 S /usr/local/samba/smbd -D
2326 nobody 1064 R ps w
last line of nvram show is: size: 21482 bytes (11286 left)
So all in all my question is where i go from here if i want dd-wrt to run on my new router? Does dd-wrt support NAND so i can do as described here? (studying computer science so I'm not afraid of compiling stuff)
Thanks in advance and please bear with any spelling mistakes as English isn't my primary language