TENDA W311R - Bad flash recover and Install dd-wrt firmware!

Post new topic   Reply to topic    DD-WRT Forum Index -> Ralink SoC based Hardware
Goto page Previous  1, 2, 3 ... 14, 15, 16 ... 21, 22, 23  Next
View previous topic :: View next topic  
Author Message
TendaW311R+
DD-WRT User


Joined: 19 Oct 2011
Posts: 354
PostPosted: Mon Jan 16, 2012 14:23    Post subject: Reply with quote
When udentified TX RX GND I will configure putty like that. Please look at the picture
Back to top View user's profile Send private message
Sponsor
TendaW311R+
DD-WRT User


Joined: 19 Oct 2011
Posts: 354
PostPosted: Mon Jan 16, 2012 18:02    Post subject: Reply with quote
I post picture of cable. Sorry for big size, but when you tell about it I will deteted. Thanks again

Last edited by TendaW311R+ on Thu Jan 19, 2012 14:18; edited 1 time in total
Back to top View user's profile Send private message
TendaW311R+
DD-WRT User


Joined: 19 Oct 2011
Posts: 354
PostPosted: Tue Jan 17, 2012 19:01    Post subject: Reply with quote
PLEASE !!! SOMEBODY HELP ME !!!
Back to top View user's profile Send private message
RogFanther
DD-WRT User


Joined: 24 May 2008
Posts: 156
PostPosted: Tue Jan 17, 2012 23:56    Post subject: Reply with quote
One wire is ground. Measure continuity with a multimeter to the usb connector.

Then connect the other two wires to RX and Tx. Turn on the router. If not appears in the terminal, turn of the router, change places between TX and RX, then turn on the router again.
Back to top View user's profile Send private message
TendaW311R+
DD-WRT User


Joined: 19 Oct 2011
Posts: 354
PostPosted: Wed Jan 18, 2012 18:19    Post subject: Reply with quote
RogFanther wrote:
One wire is ground. Measure continuity with a multimeter to the usb connector.

Then connect the other two wires to RX and Tx. Turn on the router. If not appears in the terminal, turn of the router, change places between TX and RX, then turn on the router again.

I connected cable and see U-UBOOT. I saw it and that is a picture form it. When I hit 2 it continue with 3, but may be I have got cold solder I will thy again tomorrow and will write result. This is text form U-Boot with wrong firmware. Is it normal.
Back to top View user's profile Send private message
RogFanther
DD-WRT User


Joined: 24 May 2008
Posts: 156
PostPosted: Thu Jan 19, 2012 0:49    Post subject: Reply with quote
It shows the wrong thing, because the firmware is wrong. But the start is correct. You need to start pressing the keys repeatedly right after connecting the router to power.
Back to top View user's profile Send private message
TendaW311R+
DD-WRT User


Joined: 19 Oct 2011
Posts: 354
PostPosted: Thu Jan 19, 2012 14:22    Post subject: Reply with quote
My friend is going to soldering wires.(May be I am going to try in monday)better and try to flash with wrong firmware. Am I upload again wrong firmware ( I will not do it ) may after that repair with kapastratos' procedure ? If I use only option 2 is there any chance to brick U-BOOT ?

Is this the right configuration on putty ? ( see flow control )

What is the way to brick U-BOOT ( I will not do it )
Is there any chance to have bad sectors like kapastratos ?
Back to top View user's profile Send private message
RogFanther
DD-WRT User


Joined: 24 May 2008
Posts: 156
PostPosted: Sat Jan 21, 2012 17:57    Post subject: Reply with quote
Flow control may depend of your hardware. Try with None, Xon/Xoff and Hardware.
Back to top View user's profile Send private message
TendaW311R+
DD-WRT User


Joined: 19 Oct 2011
Posts: 354
PostPosted: Sat Jan 21, 2012 18:30    Post subject: Reply with quote
On HON/FOXX I saw U-BOOT, but I will try other functions. Is there any way to connect some wires, without solder them ?
I mean riskyless way to connect wires to motherboard of my router
Back to top View user's profile Send private message
RogFanther
DD-WRT User


Joined: 24 May 2008
Posts: 156
PostPosted: Sat Jan 21, 2012 18:52    Post subject: Reply with quote
smart use of duct tape. All that is needed is a good electrical contact, so you can be creative.
A skilled person could put nails in a piece of wood, in the right places, and tie the wires to them. Or something like that.
Back to top View user's profile Send private message
TendaW311R+
DD-WRT User


Joined: 19 Oct 2011
Posts: 354
PostPosted: Sat Jan 21, 2012 19:01    Post subject: Reply with quote
So, If I do everything right just may turn off router and put automatic settings on computer network card andd then turn it on and try to reset it with button and WEB interface, right ?
Back to top View user's profile Send private message
TendaW311R+
DD-WRT User


Joined: 19 Oct 2011
Posts: 354
PostPosted: Sat Jan 21, 2012 19:06    Post subject: Reply with quote
What is the way to brick U-BOOT ( I will not do it )
Is there any chance to have bad sectors like kapastratos ?
Back to top View user's profile Send private message
TendaW311R+
DD-WRT User


Joined: 19 Oct 2011
Posts: 354
PostPosted: Sun Jan 22, 2012 18:33    Post subject: Reply with quote
TendaW311R+ wrote:
What is the way to brick U-BOOT ( I will not do it )
Is there any chance to have bad sectors like kapastratos ?


Please help me !!! I make little hole, but little outside of white line. The line, which is black( I marked it ) is half damaged. Is my motherboard damage ?

Last edited by TendaW311R+ on Sun Jan 22, 2012 19:44; edited 1 time in total
Back to top View user's profile Send private message
TendaW311R+
DD-WRT User


Joined: 19 Oct 2011
Posts: 354
PostPosted: Sun Jan 22, 2012 19:42    Post subject: Reply with quote
TendaW311R+ wrote:
TendaW311R+ wrote:
What is the way to brick U-BOOT ( I will not do it )
Is there any chance to have bad sectors like kapastratos ?


Please help me !!! I make little hole, but little inside of white line. The line, which is black( I marked it ) is half damaged. Is my motherboard damage ?


HELP, PLESE
Back to top View user's profile Send private message
RogFanther
DD-WRT User


Joined: 24 May 2008
Posts: 156
PostPosted: Sun Jan 22, 2012 19:51    Post subject: Reply with quote
Hole where ? And why ? Post a picture of your board so that we can see it.
Back to top View user's profile Send private message
Goto page Previous  1, 2, 3 ... 14, 15, 16 ... 21, 22, 23  Next Display posts from previous:    Page 15 of 23
Post new topic   Reply to topic    DD-WRT Forum Index -> Ralink SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum