1. DDNS is ok
2. I get the DISK info for my USB HDD (ext2) displayed but it says still NOT MOUNTED. Despite this, on the NAS tab, I can see the HDD mounted at: /tmp/mnt/sda_part1. I can access the share via my network (using a OsX client) as before.
3. OpenVPN is ok.
Why do I get this error mentioned in #2?
For note, I have checked the installed modules from the kernel. Mine has almost all possible formats:
cifs ext3 hfs jbd mbcache.ko nfsd xfs
exportfs fat hfsplus jffs2 nfs nls
ext2 fuse isofs lockd nfs_common udf
edit: need to connect to the router manually every time in order to be able to use the usb share. It does not advertise itself as a samba share in LAN Older versions did.
Last edited by aht961 on Wed Dec 07, 2011 20:06; edited 1 time in total
Joined: 26 Apr 2011 Posts: 203 Location: Sacramento CA
Posted: Wed Dec 07, 2011 19:04 Post subject: Linksys E2100L
The counter stopped after 200 seconds remaining on my E2100L. After 10 minutes pulled the plug and rebooted. Came up fine and all appears OK except for USB port is not working, no lit led on USB devices to indicate a connection is made. lsmod shows that that usb_storage is loaded. dmesg seems to indicate a usb port is found but it does not detect any attached devices nor is any power supplied to any attached device. Not sure where to go from here.
<6>[ 0.990000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
<6>[ 1.030000] ar71xx-ehci ar71xx-ehci.0: Atheros AR91xx built-in EHCI controller
<6>[ 1.030000] ar71xx-ehci ar71xx-ehci.0: new USB bus registered, assigned bus number 1
<6>[ 1.070000] ar71xx-ehci ar71xx-ehci.0: irq 3, io mem 0x1b000000
<6>[ 1.090000] ar71xx-ehci ar71xx-ehci.0: USB 2.0 started, EHCI 1.00
<6>[ 1.090000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
<6>[ 1.100000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
<6>[ 1.110000] usb usb1: Product: Atheros AR91xx built-in EHCI controller
<6>[ 1.110000] usb usb1: Manufacturer: Linux 184.108.40.206-svn17952 ehci_hcd
<6>[ 1.120000] usb usb1: SerialNumber: platform
<6>[ 1.120000] hub 1-0:1.0: USB hub found
<6>[ 1.130000] hub 1-0:1.0: 1 port detected
Upgraded, not much difference from Buffalo official 17798 except that Buffalo official build reports TX power as 23dbm, community build reports as 17dbm but the received signal is the same strength. Dunno why it's reporting different power. _________________ WZR-HP-G300NH [B0 B0]
WHR-G300N V1 (Ralink)
Upgraded, not much difference from Buffalo official 17798 except that Buffalo official build reports TX power as 23dbm, community build reports as 17dbm but the received signal is the same strength. Dunno why it's reporting different power.
Requested (rather demanded) by Buffalo Inc!!! I reported that this would happen 2 months ago in the Buffalo forum. They wanted a "better" looking number. At least the dd-wrt dev staff had the integrity to NOT put up false numbers on the community release. For the Buffalo Inc Pro firmware... they are the customer and they pays the bills!!! _________________ WRT54G V1.0, build 14853 VINT mini_USB_FTP, USB mod, pixelserv
Buffalo WZR-HP-AG300H build 17461, pixelserve
Buffalo WZR-HP-G300NH, OpenWrt (trunk build 29606), ath9k drivers, pixelserv
Ubiquiti Bullet M2, AirOS