thx for the new build fractal!
i'm still not able to mount my fat32 usb stick in these builds. it mounts in kong build 17865 E3000-E4200-usb-ftp-samba3-vpn-newd.bin , however its label is MNT and UUID="FEEE-5EBA", it doesn't mount on /mnt in the kong build, but on /tmp/mnt/disc0-part1 . the h/w path is /dev/scsi/host0/bus0/target0/lun0/part1 .
i need this storage badly, so i can 't keep the fractal build on my E4200. what can i do to troubleshoot and provide more info?
edit:
nevermind. i formatted the usb stick with ext2, and called it MNT. still no dice. only after naming it Mnt i succeeded. can't do that with fat32 as volume names are uppercase in windows ( what the heck, it's still dos underneath ) _________________ now running tomato by shibby
E4200v1 cfe 2010.09.20.0
Last edited by PetervdM on Wed Nov 16, 2011 19:03; edited 1 time in total
I was able to update the build starting over from the first flash-4200, and recommended and everything ok ...
I found a problem with this build 17902 Hurricane Configuring IPv6 does not work .. The build is 17893, and changed anything? _________________ Buffalo WZR-HP-AG300H DD-WRT v24-sp2 (03/19/12) std - build 18777 + modem Digicom combo cx + Nas Synology DS-209 da 2 T + LG DP1W+ APC Back-UPS RS-Power Saving Back-UPS Pro 550 + switch Zyxel Gs105B + http://forum.emulesecurity.net/topic.asp?TOPIC_ID=3441
Last edited by djroby19 on Wed Nov 16, 2011 18:34; edited 1 time in total
thx for the quick response and new build, just try.... but bad luck... this time still not work....here is the dmesg
====
usb 1-2: new high speed USB device using ehci_hcd and address 2
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb 1-2: configuration #1 chosen from 1 choice
SCSI subsystem initialized
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
br0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
device br0 entered promiscuous mode
device vlan1 entered promiscuous mode
device eth0 entered promiscuous mode
device eth1 entered promiscuous mode
scsi 0:0:0:0: Direct-Access Generic USB Flash Disk 0.00 PQ: 0 ANSI: 2
sd 0:0:0:0: [sda] 2048000 512-byte hardware sectors (1049 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: ioctl_internal_command return code = 8000002
: Sense Key : 0x0 [current]
: ASC=0x0 ASCQ=0x0
sd 0:0:0:0: [sda] 2048000 512-byte hardware sectors (1049 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
/dev/scsi/host0/bus0/target0/lun0: p1 p2 p3
sd 0:0:0:0: [sda] Attached SCSI removable disk
usb-storage: device scan complete
....
========
thx for the quick response and new build, just try.... but bad luck... this time still not work....here is the dmesg
====
usb 1-2: new high speed USB device using ehci_hcd and address 2
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb 1-2: configuration #1 chosen from 1 choice
SCSI subsystem initialized
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
br0: Dropping NETIF_F_UFO since no NETIF_F_HW_CSUM feature.
device br0 entered promiscuous mode
device vlan1 entered promiscuous mode
device eth0 entered promiscuous mode
device eth1 entered promiscuous mode
scsi 0:0:0:0: Direct-Access Generic USB Flash Disk 0.00 PQ: 0 ANSI: 2
sd 0:0:0:0: [sda] 2048000 512-byte hardware sectors (1049 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: ioctl_internal_command return code = 8000002
: Sense Key : 0x0 [current]
: ASC=0x0 ASCQ=0x0
sd 0:0:0:0: [sda] 2048000 512-byte hardware sectors (1049 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
/dev/scsi/host0/bus0/target0/lun0: p1 p2 p3
sd 0:0:0:0: [sda] Attached SCSI removable disk
usb-storage: device scan complete
....
========
in the admin interface, it just show
Disk Info
Not available
That was very helpful information... I will put the 17902 builds and fix this... thanks for the quick response.
I had the 17902 build it kept making the router lose active feed and disconnect. It seems like it freezes the router then you would have to reboot it. Had to go back to 17893
how are you backing up your settings, i enter all of mine manually, I do want to test these latest builds.
It's just a long process to re-enter all my settings.
I'm running kong right now.
mike5026 wrote:
I had the 17902 build it kept making the router lose active feed and disconnect. It seems like it freezes the router then you would have to reboot it. Had to go back to 17893
how are you backing up your settings, i enter all of mine manually, I do want to test these latest builds.
It's just a long process to re-enter all my settings.
I'm running kong right now.
mike5026 wrote:
I had the 17902 build it kept making the router lose active feed and disconnect. It seems like it freezes the router then you would have to reboot it. Had to go back to 17893
I believe he withdraw it because that build not able to mount all usb drive.. 17893 at least can mount swap & fat32 partition _________________ Belkin N600 Play Max HD F7D4301v1
I believe he withdraw it because that build not able to mount all usb drive.. 17893 at least can mount swap & fat32 partition
Thanks for the info ..... lawleo Fractal hopefully release a new build as soon as possible _________________ Buffalo WZR-HP-AG300H DD-WRT v24-sp2 (03/19/12) std - build 18777 + modem Digicom combo cx + Nas Synology DS-209 da 2 T + LG DP1W+ APC Back-UPS RS-Power Saving Back-UPS Pro 550 + switch Zyxel Gs105B + http://forum.emulesecurity.net/topic.asp?TOPIC_ID=3441
Posted: Sun Nov 20, 2011 9:36 Post subject: Bandwitch monitor
Hello Fractal're doing quite a lot of work .. I'd love if you include in the new build Bandwitch a nice monitor like this (http://csdprojects.co.uk/ddwrt/ orhttp://www.dd-wrt.com/phpBB2/viewtopic.php?t=81432&highlight=rflow+collector) what do you think? could be done?
Appearance hearing from you ..... thanks _________________ Buffalo WZR-HP-AG300H DD-WRT v24-sp2 (03/19/12) std - build 18777 + modem Digicom combo cx + Nas Synology DS-209 da 2 T + LG DP1W+ APC Back-UPS RS-Power Saving Back-UPS Pro 550 + switch Zyxel Gs105B + http://forum.emulesecurity.net/topic.asp?TOPIC_ID=3441
Posted: Wed Nov 23, 2011 5:37 Post subject: Great work!
Just wanted to post a thanks to Fractal here, for continuing to work on this. It sounds like a lot of trouble going through the builds and troubleshooting data, but we all appreciate your efforts!
Posted: Wed Nov 23, 2011 13:22 Post subject: Re: Great work!
Lloyd wrote:
Just wanted to post a thanks to Fractal here, for continuing to work on this. It sounds like a lot of trouble going through the builds and troubleshooting data, but we all appreciate your efforts!