iPTV flood the WLAN - la TVinternet inonder le WIFI

Post new topic   Reply to topic    DD-WRT Forum Index -> Questions générales
Author Message
smike2809
DD-WRT Novice


Joined: 23 Sep 2011
Posts: 9

PostPosted: Thu Oct 27, 2011 11:03    Post subject: iPTV flood the WLAN - la TVinternet inonder le WIFI Reply with quote
Bonjour,

Depuis plusieurs mois j'ai le WIFI qui plante après que j'ai regardé la TV avec la box de mon FAI.
J'ai fait des recherches et j'ai trouvé 3 tutos qui traitent le sujet. J'ai essayé les 3 mais pour l'instant rien ne marche. Je parle pas encore très bien anglais, j'ai utilisé un traducteur pour essayer de comprendre mais ce n'est pas évident et leur interface ne coresspond pas exactement à la mienne (le wifi est bridgé sur mon WRT54GL de linksys)

site traitant le sujet:
http://www.dd-wrt.com/wiki/index.php/IPTV_-_blocking_multicast_on_WIFI
ici je ne comprends pas si il faut enregistrer les commandes dans le "startup" ou dans le "firewall".

http://www.dd-wrt.com/wiki/index.php/Separate_LAN_and_WLAN
ici je n'ai pas leur interface wl0.1 (j'ai vlan1, vlan0, eth0 et eth1)

http://www.dd-wrt.com/wiki/index.php/Separate_Lan_and_WLan
ici c'est le bordel je sais pas dans quel ordre et conditions il faut appliquer les instructions. En plus on dirait que ca n'a meme pas été tester.

équipé de :
-Linksys WRT54GL v 1.1
-firmware dd-wrt


merci énormément pour votre aide.
ca fait plusieurs moi que je cherche une solution. Beaucoup d'heures de passé
Sponsor
smike2809
DD-WRT Novice


Joined: 23 Sep 2011
Posts: 9

PostPosted: Fri Oct 28, 2011 18:01    Post subject: Reply with quote
SVP j'ai besoin d'aide
smike2809
DD-WRT Novice


Joined: 23 Sep 2011
Posts: 9

PostPosted: Fri Nov 04, 2011 23:07    Post subject: Reply with quote
J'avance peu voici ce que j'ai fais:

Lien pour séparer le Wlan du Lan:
http://www.dd-wrt.com/wiki/index.php/Separate_Lan_and_WLan#VLan_Web_Interface_Method
"Configuration

There are two methods for running separate IP ranges on each of the interfaces which yield two rather dissimilar results.
[edit] iptables Method

Rather than splitting up br0, some may find it adequate to use the Iptables command to allow routing between two subnets on the LAN/WLAN side. Since br0 is not being split up, there are no/fewer problems caused in the web interface. The major draw back to this is that if wireless users statically assign an IP on the LAN ip address range, the bridge will allow them access. A trick might be to set the WLAN ip range to the default (192.168.1.x) and the LAN ip range to something odd (10.15.25.x, or 192.168.152.x or something) to prevent WLAN users from guessing the ip range.
You can use any private ip ranges you would like, but for this example I will use 192.168.1.x for the LAN ports and 192.168.2.x for the WLAN port.
Basic Steps:
Enable a static route for 192.168.1.x to vlan0
Enable a static route for 192.168.2.x to eth1
Enable DHCP for 192.168.1.x for vlan0
Enable DHCP for 192.168.2.x for eth1"


lien pour créer une route statique:
http://www.dd-wrt.com/wiki/index.php/Linking_Subnets_with_Static_Routes

Pour faire un nouveau DHCP c'est pas difficile mais pour créer une route statique je bloque.

Ce que j'ai compris c'est qu'il faut cocher la case unbridged interface eth1 dans setup>Networking.
Puis il faut créer une route statique pour eth1 et vlan0. Mais je ne sais pas ce qu'il faut mettre dans les cases.

Pour l'instant j'ai mis ça:
1()
LAN
0
192.168.1.0
255.255.255.0
192.168.1.1
vlan0

2()
WIFI
0
192.168.2.0
255.255.255.0
192.168.1.2
eth1

Quelqu'un aurait-il les compétences nécessaires pour m'aider
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Index -> Questions générales All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum