New build - BrainSlayer 11-17-10-r15747

Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware
Goto page Previous  1, 2, 3  Next
Author Message
PetervdM
DD-WRT User


Joined: 11 Jun 2009
Posts: 282
Location: EU

PostPosted: Thu Nov 18, 2010 11:05    Post subject: Reply with quote
pato wrote:
My WRT610Nv1 is crashing within some seconds after bootup with this build (also was with 15508). I used the BIG version.
It works after a 30-30-30, but only until I change some settings (so far it seems it doesn't matter which ones, just a few), then it starts to crash and reboot constantly.


no problem here, running big. did you leave it alone for at least 10 minutes after the 30-30-30 reset?

_________________
now running tomato by shibby
E4200v1 cfe 2010.09.20.0
Sponsor
duncanidahoe
DD-WRT User


Joined: 29 Nov 2009
Posts: 354
Location: Dark Side of the Moon

PostPosted: Thu Nov 18, 2010 11:17    Post subject: Reply with quote
Ping time increased 3x on the 160 v3. And it has a problem with going down after a few minutes. Thought OC might help, but just made it worse. Don't want to try the e2k yet to see if problems are resolved first.
_________________
E4200 w/ mega build 23838

4 wrt160n v3 w/ BrainSlayer dd-wrt.v24-15778_NEWD-2_K2.6_std_nokaid_small.bin

2 wrt320n w/ BrainSlayer dd-wrt v24-15778 NEWD-2_K2.6_big.bin

wndr3300 w/ dd-wrt.v24-14583_NEWD_std-nokaid_nohotspot_nostor.bin

wrt54g v6 w/ Brainslayer 14594 dd-wrt.v24_micro_generic.bin

wrt400n w/ 21676 build
__________________________________

Peacock Thread | BrainSlayer Builds | Eko Builds
kt_haddock
DD-WRT Guru


Joined: 25 Dec 2009
Posts: 710

PostPosted: Thu Nov 18, 2010 16:25    Post subject: Reply with quote
I have tested this build an discovered that I'm getting wrong wan-ip number after dhcp-relese/renew Same if I reboot router.
Get-10.0.0.3 gw-10.0.0.1 dns1-10.0.0.1 but I should get 213.80.*.*.
When I do a ip-check it's 213.80.*.* but display as 10.0.0.10
After som fiddeling I get right IP. Very strange.


EDIT: Frater ticket seems to be the problem:
http://svn.dd-wrt.com:8000/dd-wrt/ticket/1854



ip-number.jpg
 Description:
 Filesize:  99.65 KB
 Viewed:  12702 Time(s)

ip-number.jpg



_________________
[I prefer answere in whole sentence]


Last edited by kt_haddock on Fri Nov 19, 2010 7:06; edited 2 times in total
pix5650
DD-WRT User


Joined: 18 Feb 2007
Posts: 87
Location: Bern, Switzerland

PostPosted: Thu Nov 18, 2010 19:41    Post subject: Reply with quote
pato wrote:
My WRT610Nv1 is crashing within some seconds after bootup with this build (also was with 15508). I used the BIG version.
It works after a 30-30-30, but only until I change some settings (so far it seems it doesn't matter which ones, just a few), then it starts to crash and reboot constantly.

Are you maybe running low on free nvram space? You can check that with following command:
Code:
nvram show |grep wan_ipaddr

_________________
Deployed:
Buffalo WZR-1750 - v3.0-r38580M kongac (02/05/19) - Router
Buffalo WZR-1750 - v3.0-r38580M kongac (02/05/19) - Client Bridge
Buffalo WZR-1750 - v3.0-r38100M kongac (12/27/18) - Router
Linksys WRT320 -> E2000 - v3.0-r33772 K30 mega (11/16/17) - Client Bridge

Others:
Buffalo WZR-1750, GL.iNet 6416, GL.iNet AR150, TP-Link TL-WR703N,
Linksys WRT610Nv2 -> E3000, Linksys E3000, Linksys E2000, Linksys WRT54GL
icewaere
DD-WRT User


Joined: 09 Sep 2010
Posts: 86

PostPosted: Thu Nov 18, 2010 20:14    Post subject: Reply with quote
Works great on my Belkin Play Max F7D4301 v1 very fast and great speed with 533mhz ;)

hope optware is up again next hours need my squid install.

any news about the ntfs support?

greetz@all

_________________
Netgear Nighthawk R7000@1400mhz / KongAC-ARM-build (25530M)
Netgear WNDR4500 DD-WRT v24-sp2 (09/27/13) kongac-build 23430 / OTRW t2 Squid 3.1.8 / 64gb SSD
Belkin Play Max F7D4301v1@533mhz / 500GB USB / 3G Huawei K3765-HV / DD-WRT 18777
Linksys E3000 with Tomato Victek
R.I.P. WRT160NL
R.I.P. WRT54GL
cjason
DD-WRT Novice


Joined: 08 Apr 2010
Posts: 20

PostPosted: Thu Nov 18, 2010 20:45    Post subject: Reply with quote
It seems that for 15747 there is no NTFS support in any version whatsoever.
wats6831
DD-WRT User


Joined: 20 Apr 2010
Posts: 205

PostPosted: Thu Nov 18, 2010 21:14    Post subject: Reply with quote
I flashed my new E3000 with 14584-e3000, then this newest build. Works great as far as I can tell. MUCH better than the stock Linksys firmware.
JohnMetsn
DD-WRT Novice


Joined: 07 Nov 2010
Posts: 23

PostPosted: Thu Nov 18, 2010 21:16    Post subject: Reply with quote
NTFS works fine for me with the BIG version...
_________________
Asus RT-N16 running DD-WRT v24-sp2 BIG SVN revision 14929
kt_haddock
DD-WRT Guru


Joined: 25 Dec 2009
Posts: 710

PostPosted: Thu Nov 18, 2010 21:19    Post subject: Reply with quote
cjason wrote:
It seems that for 15747 there is no NTFS support in any version whatsoever.



NTFS support in BIG-build, mini_usb_nas and std_usb_nas

_________________
[I prefer answere in whole sentence]
frater
DD-WRT Guru


Joined: 07 Jun 2006
Posts: 2777

PostPosted: Thu Nov 18, 2010 21:31    Post subject: Reply with quote
The DHCP-client broke again I'm afraid. Most users will not notice this. These requests normally goes to your ISP, but in my setup it goes to my modem.

It used to pass its hostname, but now it gives '1'.

If you can check the hostname could you tell me if this is the same for you?

I made a ticket for it, because it is important for my setup: http://svn.dd-wrt.com:8000/dd-wrt/ticket/1854

_________________
Asus RT16N + OTRW
Kingston 4GB USB-disk 128 MB swap + 1.4GB ext3 on /opt + 2 GB ext3 on /mnt
Copperjet 1616 modem in ZipB-config
Asterisk, pixelserv & Pound running on router
Another Asus RT16N as WDS-bridge

DD-WRT v24-sp2 vpn (c) 2010 NewMedia-NET GmbH
Release: 12/16/10 (SVN revision: 15758M)
FarmerBob
DD-WRT User


Joined: 09 Aug 2009
Posts: 86
Location: The Beach...

PostPosted: Fri Nov 19, 2010 1:10    Post subject: Reply with quote
PetervdM wrote:
no problem here, running big. did you leave it alone for at least 10 minutes after the 30-30-30 reset?


I thought it was:
• 30-30-30
• Install Firmware
– wait for reboot and if successful reenter login info . . .
• Power Cycle
– then wait the "10 minutes" or is it "go get a beer"? I find the going and getting a beer the better solution.
• 30-30-30
and now you're good to go . . .
pato
DD-WRT Novice


Joined: 20 Mar 2007
Posts: 32

PostPosted: Fri Nov 19, 2010 10:19    Post subject: Reply with quote
pix5650 wrote:
pato wrote:
My WRT610Nv1 is crashing within some seconds after bootup with this build (also was with 15508). I used the BIG version.
It works after a 30-30-30, but only until I change some settings (so far it seems it doesn't matter which ones, just a few), then it starts to crash and reboot constantly.

Are you maybe running low on free nvram space? You can check that with following command:
Code:
nvram show |grep wan_ipaddr

Currently, back at 15396 it looks like this:

root@DD-WRT:~# nvram show
size: 30813 bytes (1955 left)

Not really much left there.
bskchaos
DD-WRT User


Joined: 07 Feb 2009
Posts: 198

PostPosted: Fri Nov 19, 2010 11:36    Post subject: Reply with quote
Except for a weird problem last night everything in my network seems to be working, Except that OpenVPN is not loggin anything to syslog.

Can someone please confirm this? I'm using the new conf. dialog.
raym
DD-WRT Novice


Joined: 22 Jul 2010
Posts: 42

PostPosted: Fri Nov 19, 2010 21:54    Post subject: Reply with quote
just flashed a wrt160n v3 set up as an access point and it's working very well. I'll leave this on for a few days and then flash my main router
edrikk
DD-WRT User


Joined: 31 Oct 2009
Posts: 186
Location: Canada

PostPosted: Sat Nov 20, 2010 22:37    Post subject: Reply with quote
For some reason with this buid, I've had clients to my WRT610Nv2 not be able to connect to the wireless (both N and G) on two occasions.

I've had to reboot the router to get it back.

I'm downgrading back to 15693...
Goto page Previous  1, 2, 3  Next Display posts from previous:    Page 2 of 3
Post new topic   Reply to topic    DD-WRT Forum Forum Index -> Broadcom SoC based Hardware All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum