i tried to compile timbuktus new 102 mb source file and i end up in this
make[4]: Leaving directory `/kamikaze_r5946/package/wireless-tools'
make[3]: Leaving directory `/kamikaze_r5946/package'
ln: creating symbolic link `/kamikaze_r5946/build_mips/root/etc/rc.d/S10boot' to `/etc/init.d/boot': No such file or directory
ln: creating symbolic link `/kamikaze_r5946/build_mips/root/etc/rc.d/S50cron' to `/etc/init.d/cron': No such file or directory
ln: creating symbolic link `/kamikaze_r5946/build_mips/root/etc/rc.d/S60dnsmasq' to `/etc/init.d/dnsmasq': No such file or directory
ln: creating symbolic link `/kamikaze_r5946/build_mips/root/etc/rc.d/S50dropbear' to `/etc/init.d/dropbear': No such file or directory
ln: creating symbolic link `/kamikaze_r5946/build_mips/root/etc/rc.d/S45firewall' to `/etc/init.d/firewall': No such file or directory
ln: creating symbolic link `/kamikaze_r5946/build_mips/root/etc/rc.d/S50httpd' to `/etc/init.d/httpd': No such file or directory
ln: creating symbolic link `/kamikaze_r5946/build_mips/root/etc/rc.d/S40network' to `/etc/init.d/network': No such file or directory
ln: creating symbolic link `/kamikaze_r5946/build_mips/root/etc/rc.d/S50telnet' to `/etc/init.d/telnet': No such file or directory
make[2]: *** [install] Error 1
make[2]: Leaving directory `/kamikaze_r5946/package'
make[1]: *** [package/install] Error 2
make[1]: Leaving directory `/kamikaze_r5946'
Build failed. Please re-run make with V=99 to see what's going on
make: *** [world] Error 1
Hi Andre(hw0012),
I guess you turned it off while it was flashing or something went wrong during the flash process. Serai console should be sufficient. In case it is not, JTAG will resurrect your Fonera.
after enter, the Fonera startet rebooting (ssh connections was closed). Does the flash process start during the reboot? (sorry for my dump question) Because after about ~5 Minutes after the reboots nothing was happening, so i pulled the power of it. Should I wait longer on this Process? I order 2 new Foneras and Serial MAX232 Kit, so it will be good to know it better next time. How long can the flashing last, after the reboot (the first 4 Lines of the tutorial)?
Posted: Tue Jan 02, 2007 22:58 Post subject: WHAT MEANS THIS ERROR?
Hi I have installed kamikaze r5959 kernel 2.6 in my fonera but i get this screen in starting up...
BusyBox v1.3.1 (2007-01-02 00:12:29 CET) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
/bin/ash: can't access tty; job control turned off
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
KAMIKAZE (bleeding edge, r5959) -------------------
* 10 oz Vodka Shake well with ice and strain
* 10 oz Triple sec mixture into 10 shot glasses.
* 10 oz lime juice Salute!
---------------------------------------------------
What means the line
/bin/ash: can't access tty; job control turned off? How can i solve it? Thanks
I ran into the same problem as hw0012, and now have a bricked fonera. I ended up making serial cable and am able to get to redboot. So my question is do i just pick up on step 6 of Camicia's how to?
Thanks,
Joe
I recently aquired a few La Fonera routers through their "Fonero gets Fonera" program for the holidays, and have been trying to get at least one of them into client mode for a while now. I was trying to manually reconfigure the wireless connections and routes and such, but now that DD-WRT has been released for it, I would like to try and reflash, as it seems a bit easier to configure. I attempted to follow your tutorial here, and I came across a problem in the first couple steps.
I already had SSH enabled, so that wasn't an issue, but after I had downloaded the image you hosted, I had trouble rewriting the firmware. I used the "mtd -e ..." command, checked spelling and everything multiple times, but every time I ran it, it would spit back
Code:
Could not open mtd device: vmlinux.bin.17
Can't open device for writing!
And it would then drop me back at a prompt.
If anyone has any idea what that means, please help me out.
telnet to it (maybe there will be an error with vmlinux but don't care about)
and than step by step writing the vmlinux image(download with tftp) ... and so on
Have somebody this problem or know how to solve it?
Thanks!
ruitalia
Did you make sure your internet was not plugged in when you got it? if it auto-updated, you can just reset your settings via your reset button on the bottom on the fonera.
Yes, when i tried to flash the Internet cable was unplugged. I have read some infos about it and i discovered that v 0.7.1.2 does not support this flash [i upgraded my self to v 0.7.1.2] and i cant reset to v 0.7.1.1 to future flash.