Posted: Sat Jul 04, 2009 20:36 Post subject: DD-wrt on a bullet very slow
I installed DD-wrt on a bullet2HP. On the first day I had the problem. At the outset, he was working and then the program did not respond to me. I am prepared Firmware old bullets, then installed DD-wrt again, worked well at first, and in response the next day has become very slow.
Help??????
I found a version (Bullet2 (HP) - v24 preSP2 - Build 11495,should be a beta version!!!) What should I do? Can I upgrade or install again. What about the license key?.
Joined: 05 May 2008 Posts: 62 Location: Near Area 51, Nevada
Posted: Thu Jul 09, 2009 9:36 Post subject:
Mine runs really strangely, and slow, sometimes, too. I gave it a better power supply, and run it at 25db, and it runs allright. Im using: DD-WRT v24-sp2 (01/29/09) std
(SVN revision 11514), I'll update mine, too, and see if that makes a difference.
Appreciate this thread, thanks.
"Bite the Bullet" _________________ Perfect Cantenna: Use the big spagetti sauce cans, 3-1/4" diameter. Make the element 31mm long, and place the element exactly 2-1/2" from the bottom of the can. The dimentions are critical, and these are perfect.
I have the same issue on a bullet2, not the HP but the simple bullet2.
I accidentially DL the firmware mentioned here and loaded it, it seemed to be missing some function, when I rereat the thread and looked at teh FW image name, I saw it was HP, so I went back to the lates release I could find, DD-WRT v24-sp2 (07/21/09) std. I did change the GUI style to xirian, and it seems to perform slightly peppier, but that may just be anecdotal.
I do have to confess that I did not do a 30/30/30, as the actual unit is 45 foot up on a tower and going out and getting it is a pain. I will do it eventually though and go through the whole flashing process. I did do a factory reset, power cycle, factory rest, power cycle, load ddwrt, factory reset, powercycle, factory reset, powercycle, configure (closest I could get without climbing)
Is this a known issue on the bullet due to its limited memory, then Im not overly concerned.
Ive tried accessing in IE, Opera, and chrome, with the same result.
Is there a better image to load? (I have professional activation on this so I dont want to mess to much and invalidate my license key)
any help would be appreciated.
If the only solution is to not use the cheapest radio I could find, then just tell me, I have thick skin.
Note, I am very new to dd-wrt, and this is probably a new guy screw up, im well aware of that, and that there is probably something (30/30/30 excluded) very simple and plainly documented that I have missed
Note, I am very new to dd-wrt, and this is probably a new guy screw up, im well aware of that, and that there is probably something (30/30/30 excluded) very simple and plainly documented that I have missed
its not your problem
is just the atheros driver that is a big bulshit
look at my speeds at only 700m on a 27dBm senao eoc-2610 with the latest build
@mochoandre, I have a network running at almost the same distance as yours, and in the past I had also 40% signal quality, which was giving me minimum 36Mbps and most of the time 48Mbps.
There is definetely an issue with your configuration, it might be parasites in your area. GeeTek gave you some advices, but you did not come back with the results.
Would be nice stopping telling everybody you paid 42 euros for a product which is not working, as dd-wrt works fine. You should investigate deeper, it might be an hardware issue also.
Michel _________________ 2x EOC-2160 - AP 2x14dB Yagy to 450m link
2x EOC-2160 - RP 2x17dB Panels - 2x 7Mbps
1x WRT54G v2.2 - V24-SP2 13577VPN Eko
All Senao EOC-2610 V1.10 Std 15362 BS
1x UBNT Bullet 2 - RP 18dB Panel - 11Mbps - 13Km link
Note, I am very new to dd-wrt, and this is probably a new guy screw up, im well aware of that, and that there is probably something (30/30/30 excluded) very simple and plainly documented that I have missed
its not your problem
is just the atheros driver that is a big bulshit
look at my speeds at only 700m on a 27dBm senao eoc-2610 with the latest build
and i've payed 42 € for this and now I cant revert to fatctory firmware
ok...last chance 4 u.
go focus on your setup problem and dont worry other people with your non knowledge of ddwrt. the driver and system is proved on many thousands of prof ap's around the world so its no ddwrt problem
if u still bash around i will lock your account. _________________ Forum Guidelines...How to get help
&
Forum Rules
&
RTFM/STFW
&
Throw some buzzwords into the WIKI search
_________________
I'm NOT rude, just offer pure facts!
_________________
Atheros (TP-Link & Clones, etc ) debrick service in EU
_________________
Guide on HowTo be Safe, Secure and Protect Your Online Anonymity!
@mochoandre, I have a network running at almost the same distance as yours, and in the past I had also 40% signal quality, which was giving me minimum 36Mbps and most of the time 48Mbps.
There is definetely an issue with your configuration, it might be parasites in your area. GeeTek gave you some advices, but you did not come back with the results.
Would be nice stopping telling everybody you paid 42 euros for a product which is not working, as dd-wrt works fine. You should investigate deeper, it might be an hardware issue also.
Michel
I must say I already use dd-wrt for 2 or 3 years with very good results in linksys WRT54GL, WRT54GS and foneras.
The problems is with this 2 eoc-2610 wich I have invested a considerable amount of money to get a better connection but are performing very poorly
About the geektek configuration, I apreciate, but i did not come back with the results because they were the same.
Quote:
ok...last chance 4 u.
go focus on your setup problem and dont worry other people with your non knowledge of ddwrt. the driver and system is proved on many thousands of prof ap's around the world so its no ddwrt problem
if u still bash around i will lock your account.
Should I be scare?
why? can't we talk here freely ?
as I said in other post i've tryed hundreds of configuration combinations and firmware build all performing poorly.
And it seems to me that you have an almighty wisdom judging for the tone you speek maybe you can give me some configuration enlightment instead of just saying its a problem with my configuration
