I've just put DD-WRT on my G2v1. Brilliant. I had a fon 2100 which I managed to brick (I think) and the ease of installing onto the G2 was amazingly simple compared to the fon.
I must admit though, I was looking forward to all the telnet stuff that I had to do with the fon
I did a scan and only tcp 21 and 80 ports are open and tftp takes udp 69 I believe and my networkactiv port scanner can't connect via any udp ports. What can I do to open that port? Or what am I doing incorrectly?
I did a scan and only tcp 21 and 80 ports are open and tftp takes udp 69 I believe and my networkactiv port scanner can't connect via any udp ports. What can I do to open that port? Or what am I doing incorrectly?
I switched to my laptop and it upgraded fine. Weird with the PC.
Hi,
First of all I would like to thank you very much for this firmware. My WRT54G2 router was restarting itself very often and I was getting crazy because of this. I have contact linksys support twice but they were not very professional (or maybe that's because they don't have a solution for this). So I get no help from linksys...
However after I've put this firmware everything seems to work more than ok except that the led near refresh button is not green anymore and is always orange. Is this a big problem? As I said everything works perfect...
Joined: 06 Jun 2006 Posts: 37 Location: Montreal, Canada
Posted: Tue Jan 06, 2009 2:01 Post subject:
Hey, sorry to hop in like this, but I followed the procedure, I can configure everything in the firmware, all seems fine, except that I cannot know if the HARD RESET procedure worked or not.
I pressed on the back button 30sec, nothing flashed nor changed color. I then did a power cycle to make sure. All is fine so far in the firmware.
How can I know the factory defaults have been applied by the hard reset, if it worked, since I did not change anything previously anyway?
For the moment I am not using it, until I can make sure it is safe to use it.
tnx _________________ Frank
Montreal, Canada
Buffalo WHR-G54S v24-sp1
WRT54G2 v24 sp1
WRT54G v5 v24 sp1
Weird WRT54G v1.0 not working
Linux openSUSE 10.3 KDE 64-bits
Joined: 04 Jan 2007 Posts: 11564 Location: Wherever the wind blows- North America
Posted: Tue Jan 06, 2009 13:55 Post subject:
There is only one way to revert back to default Linksys....that is via JTAG but only if you have a wholeflash of the unit from before upgrading to dd-wrt.
redhawk _________________ The only stupid question....is the unasked one.
There is only one way to revert back to default Linksys....that is via JTAG but only if you have a wholeflash of the unit from before upgrading to dd-wrt.
redhawk
I downloaded the latest image from the linksys website, will that help?
Joined: 04 Jan 2007 Posts: 11564 Location: Wherever the wind blows- North America
Posted: Tue Jan 06, 2009 17:40 Post subject:
hashaam83 wrote:
redhawk0 wrote:
There is only one way to revert back to default Linksys....that is via JTAG but only if you have a wholeflash of the unit from before upgrading to dd-wrt.
redhawk
I downloaded the latest image from the linksys website, will that help?
hashaam83
No...you would have to have a JTAG'd backup of a wholeflash from YOUR unit to recover. It is the only method of reversion possible at this time.
Unless you took your virgin unit and did a wholeflash.bin backup using JTAG before loading dd-wrt on it...then you are out of luck.
redhawk _________________ The only stupid question....is the unasked one.
