Joined: 01 Jun 2007 Posts: 11 Location: Costa Rica
Posted: Mon Jan 28, 2008 18:57 Post subject: Help Gateworks. I can pay support help!
Hello;
I have 2 gateworks 2348-2, each unit have installed the Ubiquiti XR-3. I have not the superchannel, I have enable the outdoor band, regulatory domain ARMENIA, I am using the channel 128.
The trouble is that each time that I need change some configuration in the wireless, I need remove the wireless card, put the AP to factory default, put the card inside again, factory default again, and finally I can config without errors the channel values.
when I do this, I put in WDS, each unit in AP mode, A only, but the system is jumping, never is stable, when I saw the status, I see the other WDS, but only for some seconds, after that, the other AP disapper from the status.
When I tried "scan 0" I din't see nothing.
I have 2 antennas 3.5 GHZ 13.5dBi, low loss cable LMR-400 (1 metter) and less than 3 Km distance between points. when I used the superchannel from july that Brian provide us, everything works, but the trouble was that when we like to do some changes, we cannot because we needed to do the procedure explained to config the system again.
Can you help me. I can pay support, I believe that could be a compatibility or someting like that.
When the SITE SURVEY will be ready?
I have the last version DD-WRT for AVILA
HELP!!!
_________________ Wireless Xtreme
DD-WRT v24 Beta Lastest - WRT54G v2-3-4-5
Gateworks and X86
Dont feel alone, im having similar problems but with a Ubiquiti XR5 cards, I have 4 cards installed, but i can just see the first card with all 5ghz channels, the other three cards just appears channel 165.... :S
Hope BrainSlayer can put any comment regarding this...
Heres some output via telnet from the frequencies i can choose
Code:
~ # iwlist ath1 frequency
ath1 1 channels in total; available frequencies :
Channel 165 : 5.825 GHz
Current Frequency:5.825 GHz (Channel 165)
~ # iwlist ath2 frequency
ath2 1 channels in total; available frequencies :
Channel 165 : 5.825 GHz
Current Frequency:5.825 GHz (Channel 165)
~ # iwlist ath3 frequency
ath3 1 channels in total; available frequencies :
Channel 165 : 5.825 GHz
Current Frequency:5.825 GHz (Channel 165)
~ #
This makes me think its not just a simple GUI problem, rather something inside the kernel/wireless utils/config
UPDATE:
I just did a reset to default, and now all channels appear back... so there must be an option that make all the other frequencies to be disabled (right now im reconfiguring everithing and monitoring if they disappear)
Joined: 01 Jun 2007 Posts: 11 Location: Costa Rica
Posted: Tue Jan 29, 2008 0:25 Post subject: I have an update
After reset default, and reboot, finally I have 2 equipments ready, but in front each other, the main problem is that only can use 9Mb, the equipments have -24 Signal and 92% good quality, channel 100, and look that works, but when I tried to do a change in the rate, again, I need to repeat everything, the factory default, remove and put the card... bla, bla, bla...
Help _________________ Wireless Xtreme
DD-WRT v24 Beta Lastest - WRT54G v2-3-4-5
Gateworks and X86
My take 6.2 is broken for Avlila at least for Atheros card support with anything other than WEP encyrption and I'm anxioulsy awaiting the next release. Would be nice if CF cards where autodetected and mounted as well is all this extra flash space for JFFS2. _________________ *********************
DD-WRT v23SP2
WRT54GS 2.1 @ 216 Mhz
SD Mod w/ 512 MB Card & Dual Serial Ports
My take 6.2 is broken for Avlila at least for Atheros card support with anything other than WEP encyrption and I'm anxioulsy awaiting the next release. Would be nice if CF cards where autodetected and mounted as well is all this extra flash space for JFFS2.
Im using a passive PoE 24V adapater.. according to the avila tech guys they said it should have any probs powering these boards, so far i could get them to work corretly having just 2 radios correctly configured. (I couldnt reproduce the missing channels probs, but i know if i start playing with the web ui i might brake it again, that means no more tweaking for it :p) The other two are connected, and have a SSID configured and all, just it has no clients connected to it, yet. (This equipment is being used as wireless backhaul for some remote offices)
Joined: 01 Jun 2007 Posts: 11 Location: Costa Rica
Posted: Wed Jan 30, 2008 20:35 Post subject: Help
Hello, Finally I put the system working,
When you save something, you need to hold the green light of the board will be ready, because you can changes things, but the system crash if the light are no turned ON. when you save, hold like a minute, and after that you can save anything.
This is a nice trick.... _________________ Wireless Xtreme
DD-WRT v24 Beta Lastest - WRT54G v2-3-4-5
Gateworks and X86