Posted: Sat Oct 04, 2025 17:46 Post subject: New Build - 10/04/2025 - r62240
Welcome to x86 / x64 r62240 beta release thread for reporting, feedback to developers & community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp) 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Debug Analyze: stracetcpdump.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Joined: 25 Aug 2020 Posts: 57 Location: New York, USA
Posted: Sun Oct 05, 2025 3:07 Post subject:
Router/Version: HP EliteDesk 800 G2 Mini PC [i3-6100T], r62240
File/Kernel: dd-wrt_x64-webupgrade_full_vga_2GB.bin
Previous/Reset: r61613 06/02/2025, no
Mode/Status: gateway/router, OK
Issues/Errors: internet speed is very low post-upgrade, only a couple of megabits per second (1-5 mbps, supposed to be 400 mbps). webpages take ages to load. previous versions of dd-wrt have had issues with qos, hence my hesitation to upgrade recently. i've reverted to r61613. _________________ HP EliteDesk 800 G2 Mini PC [i3-6100T] (WAN, DHCP, QoS)
TP-Link BE9300 (AP)
NETGEAR WNDR4300 (Switch)
Router/Version: industrial PC N4000 4GB RAM, 2*intel i226-v
File: dd-wrt_x64-webupgrade_full_vga_2GB.bin
Firmware: DD-WRT v3.0-r62240 std (10/04/25)
Kernel: Linux 6.12.49 #247 SMP Sat Oct 4 02:08:49 +07 2025 x86_64
Mode: Gateway, SFE disabled, Wireguard for external access, WAN (PPPoE/VLAN7) to GPON Modem, Automatic Drive Mount disabled - using own mount script for USB Disk, nfs to access USB3-ext4 SSD, Force reconnect 5:00 in the morning, using my own local NTP, CPU governour set to ondemand by script, Ignore WAN DNS, Recursive DNS Resolving (Unbound).
Reset: No
Status: Installed yesterday, ERROR.
PPPoE does not start after reboot. Status --> WAN states disconnected, but nothing happens. You have to click "connect" there in order to connect.
This behaviour started with three builds before previous release.
You can reboot the router and wait but rp-pppoe.so gets not loaded and pppd 2.4.8 isn't started before you click on disconnect.
WAN Speed is fine for IPv4 but not IPv6.
iperf3 -c URL -6 gives one digit figures in my network, except when used on the router, there it maxes out my line.
Only upstream is affected, exchanged my switch, DD-WRT Router and cables.
Same issue, seemingly related to nat66.
Will investigate further.
Last edited by Zyxx on Tue Oct 07, 2025 17:08; edited 4 times in total
Posted: Mon Oct 06, 2025 21:11 Post subject: New Build - 10/04/2025 - r62240
Gigabyte Technology Co., Ltd. Z97X-Gaming 3 DD-WRT v3.0-r62240 std (10/04/25) Linux 6.12.49 #247 SMP Sat Oct 4 02:08:49 +07 2025 x86_64 Intel(R) Core(TM) i7-5775C CPU @ 3.30GHz 32gb ddr3 Automatic Configuration-DHCP Up and running for 48 hrs seems like a good build plus running hfsc+cake thanks again devs oh and by the way anyway we can get cake+piece of cake sqm coding, oh and sfe is disable too.
