Posted: Sat May 17, 2025 10:15 Post subject: New Build - 05/17/2025 - r61337
Welcome to Atheros r61337 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp) 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Debug Analyze: stracetcpdump.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Posted: Sat May 17, 2025 18:37 Post subject: Linksys MR7350
Update method: WebUpgrade
Router/Version: Linksys MR7350
File: 61337
Previous/Reset: 61264 / no
Mode/Status: Gateway / ok
Issues/Errors: If you are seeing this post, all is ok
Thank you again BS and friends.
�\0
Router Model TP-Link TL-WR841ND v11
Firmware Version DD-WRT v3.0-r61337 std (05/17/25)
Kernel Version Linux 3.18.140-d6 #239571 Sat May 17 11:51:38 +07 2025 mips
Upgrade from r61298 via CLI
Working OK as AP, N/G mixed, HT40
Issues: nothing new and/or important.
This seems to be a good firmware, I managed to get an A at this this bufferbloat test with QoS, HFSC + FQ_Codel. Usually I get a D or C. I know there are many variables involved with these tests, including crowding in my wifi neigborhood at the time of the test, but I like to believe it's a win for this firmware.
Many thanks to BS! _________________ Router:TP-Link TL-WR841ND v11
Posted: Sat May 17, 2025 22:52 Post subject: WR841ND
Router/Version: TP-Link TL-WR841ND v11
Update method: WebUpgrade
File/Kernel: tl-wr841nd-webflash.bin_r61337 / Linux 3.18.140-d6 #239571 Sat May 17 11:51:38 +07 2025 mips
Previous/Reset: r61298 / no
Mode/Status: AP wired and wireless / Up and running for 4:38
Issues/Errors: Nothing significant
If your router's light turns red, don't worry. Internet connection is ok.
Incorrect rate of wlan0 - 800 Mbit/s!
Thank you BS and gurus! _________________ Atheros
Netgear XR500 Nighthawk - DD-WRT 59468
Tp-Link TL-WDR4900 v1.3 - DD-WRT 53133
TP-Link WR1043ND v4 - DD-WRT 51838
TP-Link WR1043ND v2 - Gargoyle OS 1.13.0
TP-Link WR841ND v11 - DD-WRT 60586
Broadcom
Asus RT-AC88U - DD-WRT 60586
Asus RT-AC87U R - DD-WRT 60586
Asus RT-N66U - DD-WRT 60511
Linksys WRT54GL v1.1 - DD-WRT 54517M
Linksys WRT54GL v1.1 - FreshTomato 2023.4_MIPS_K26
Linksys WRT54GL v1.1 - Gargoyle OS 1.6.2
After some time web interface stops responding, httpd crashed? Cannot get any logs at the moment. After reboot it's fine again for a while. I think it started happening a build or two back. R7800.
Update method: CLI / SSH flash from konsole over wireless
Router/Version: Linksys MX4200 v1
File/Kernel: dd-wrt-webflash.bin / Linux 6.6.90-rt29 #3315 SMP Sat May 17 10:54:40 +07 2025 aarch64
Previous/Reset: 61298 / No reset, last reset at 61202
Mode/Status: Gateway, AP, PPPoE, NSS-ECM, WAN to ONT, non-default router IP, SmartDNS for DoT, DDNS (TLS enabled), wireguard server (preshared key, non-default port), SSHD (public key only, non-default port), no VAP, wlan0 5GHz VHT80 AC only, wlan1 2.4GHz HT40 N only, wlan2 5GHz HE80 AX only, WPA3 Personal CCMP-128 all radios, domain Panama, TX power 20dBm all radios / Working
Issues/Errors: From build 61238, write command for CLI flash no longer shows write status during flash nor CRC status at end of flash.
Joined: 03 Nov 2015 Posts: 373 Location: Florida, USA
Posted: Sun May 18, 2025 1:50 Post subject:
Router: Netgear R7800 ... WDS AP
............ Netgear R7800 ... WDS Station
Firmware: DD-WRT v3.0-r61337 std (05/17/25)
Kernel: Linux 6.1.138-rt28 #577 SMP Fri May 16 03:00:12 +07 2025 armv7l
Reset: NO ...GUI upgrade from r60791
Mode: 2.4 GHz only .. Firmware type VANILLA ..SFE Disabled
Errors: NONE
...Tough to beat the last build I was on but this looks alright so far...Thanks BS and all !! _________________ ......All GOOD here... Just Handshakes and Time Stamps !......
Decided to try this build on my DIR-862L before attempting it on my EA8500. Successfully flashed via the web interface. After reboot, web GUI was inaccessible. SSH was still useable and attempted the reboot command.
Despite only being a 3rd router on the network with only wired connections to my PC, a printer, network storage drive and the wired connection to my EA8500; attempting the reboot command ended up bringing down internet connectivity for all devices on my network including wired and wireless clients connected to my EA8500 AP and the ISP provided Gateway/AP. SSH was also no longer accessible and I had to physically power off/on.
Segregated the 862L from the rest of the network and tried to access the web GUI - it started to load but was incomplete/corrupt and then became inaccessible. SSH was accessible. Powered off/on again to be safe and used SSH to revert back to r60742 and all is well again.
Joined: 05 Oct 2008 Posts: 790 Location: Helsinki, Finland / nr. Alkmaar, Netherlands
Posted: Sun May 18, 2025 3:40 Post subject:
AsX wrote:
After some time web interface stops responding, httpd crashed? Cannot get any logs at the moment. After reboot it's fine again for a while. I think it started happening a build or two back. R7800.
I have experienced the same with my R7800 in both Firefox and Chrome, latest versions, on my Linux Mint work station. I have since installed Palemoon and with that browser there is no crashing of https.
How do I know it’s https crashing when there’s nothing about that in the log?
Well, if you log in to the router with ssh and restart httpd, the gui starts responding again without having to reboot the router.
I think the commands are: stopservice httpd && startservice httpd, but you could search the forum for the correct syntax which is different from that on my LMDE 6 workstation.
As long as you have a gui page open in another browser, Palemoon can’t prevent httpd crashing sometimes. I do use Firefox to save GUI settings pages as html files with Save Page WE, but better close the page right away.
the reboot command ended up bringing down internet connectivity for all devices on my network including wired and wireless clients connected to my EA8500 AP and the ISP provided Gateway/AP. SSH was also no longer accessible and I had to physically power off/on.
This sounds like somehow a network loop was created, which would pretty much kill all network activity, including wifi and wan.
I have experienced this as well with a far downstream (from gateway) EA8500 having the ability to totally paralyse my network. I attributed it to a double NAT condition and still think it was, but in your case, seems different. Do you happen to have the WAN connected to anything, or only the LAN ports? _________________ - Linksys EA8500: I-Gateway, WAP/VAP 5ghz only. Features: VLANs, Samba, WG, Entware - r60xxx
- Linksys EA8500: 802.11s Secondary w/VLAN Trunk over 5ghz - r60xxx
- Linksys MX4300: 802.11s Primary w/VLAN Trunk over 5ghz. 2.4ghz WAP/VAP only - r60xxx
- Linksys MX4300: (WAP/VAP (7)) Multiple VLANs over single trunk port. Entware/Samba r60xxx
- Linksys MR7350: WDS Station for extended Ethernet r60xxx
- Linksys MR7500, MX8500: None in production. Just testing. r60xxx
- OSes: Fedora 40, 10 RPis (2,3,4,5), 23 ESP8266s: Straight from Amiga to Linux in '95, never having owned a Windows PC.
- Forum member #248
Joined: 05 Oct 2008 Posts: 790 Location: Helsinki, Finland / nr. Alkmaar, Netherlands
Posted: Sun May 18, 2025 8:31 Post subject:
Port status came back with the previous build, but on this build in my R7800 it is preparing for something that isn't there. Three boxes to the right of wan without content.
The previous build showed only the 4 lan ports and wan. Something changed with the last update.
Schermafdruk van 2025-05-18 10-24-44.png
Description:
R7800, build 61337, no tagging, but an IoT VAP and one for guests. In addition a VLAN on port #4 with its own DHCP as well. That's three extra DHCP's. Perhaps the three empty places are for those...
