Posted: Mon Mar 24, 2025 7:25 Post subject: New Build - 03/24/2025 - r60467
Welcome to x86 / x64 r60467 beta release thread for reporting, feedback to developers & community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp) 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Debug Analyze: stracetcpdump.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Router/Version: Dell Optiplex 5050 with i7-6700 & 16 GB RAM. Also have a dual gb PCI-E Network card.
File/Kernel: Full 2GB VGA
Previous/Reset: 60121
Mode/Status: Router
Issues/Errors: None after two hours _________________ X86_64 build PC w/ i7-6700 & 16 GB RAM (DDWRT Build r60662)
2 R7800's (DDWRT Build r60586) I use one as an AP and the other is a spare
GL.iNET GL-MT6000 Flnt 2 with OpenWRT as an AP
3 R7000's (DDWRT build r53843) not in use
Netgear WNDR 3400 (DDWRT r55630) not in use
Netgear DGND 3700 (with OpenWRT) not in use
WRT54G-TM not in use
Router/Version: Dell Optiplex 5050 with i7-6700 & 16 GB RAM. Also have a dual gb PCI-E Network card.
File/Kernel: Full 2GB VGA
Previous/Reset: 60121
Mode/Status: Router
Issues/Errors: None after two hours
My x64 system loads it just fine had to roll back to 60121. Every computer in the home doesn't have internet access with this version loaded. It does get an IP address from the cable modem both ipv4 and ipv6 addresses. Just no computer or phone has access to anything on the internet. Works fine with 60121. Did you reset the configuration or what pci-E card you got?
Router/Version: Dell Optiplex 5050 with i7-6700 & 16 GB RAM. Also have a dual gb PCI-E Network card.
File/Kernel: Full 2GB VGA
Previous/Reset: 60121
Mode/Status: Router
Issues/Errors: None after two hours
My x64 system loads it just fine had to roll back to 60121. Every computer in the home doesn't have internet access with this version loaded. It does get an IP address from the cable modem both ipv4 and ipv6 addresses. Just no computer or phone has access to anything on the internet. Works fine with 60121. Did you reset the configuration or what pci-E card you got?
I did not do a reset when I upgraded to this one. I honestly do not know what PCIE card I have. It is a 2 port gigabit card. I am working from home right now so I do not want to open up the computer to look right now. I actually just ordered a 4 port 2.5 gb card with the Realtek chip that should be here by Sunday. I just received the GL.iNET GL-MT6000 Flint 2 I ordered a few days ago to use an an access point. I figured I would take advantage of the 2.5 GB port on the Flint 2 hence why I ordered the new 4 port card. I will get the model of my current card when I swap it out when the new one comes in. _________________ X86_64 build PC w/ i7-6700 & 16 GB RAM (DDWRT Build r60662)
2 R7800's (DDWRT Build r60586) I use one as an AP and the other is a spare
GL.iNET GL-MT6000 Flnt 2 with OpenWRT as an AP
3 R7000's (DDWRT build r53843) not in use
Netgear WNDR 3400 (DDWRT r55630) not in use
Netgear DGND 3700 (with OpenWRT) not in use
WRT54G-TM not in use
Try it with the 4 port realtek 2.5Gbps card. Since that is what I got for NIC is a realtek based. My card is the 6 port version. Also the onboard NIC is a realtek 1Gbps which is what it's connected to my cable modem. The 2.5 is setup only for the LAN side of things. Not sure which one is the problem since I can access the WEBGUI just fine. Just anything on the internet stops working. May try the next version to see if it works and if I can access the modem information webgui.
Try it with the 4 port realtek 2.5Gbps card. Since that is what I got for NIC is a realtek based. My card is the 6 port version. Also the onboard NIC is a realtek 1Gbps which is what it's connected to my cable modem. The 2.5 is setup only for the LAN side of things. Not sure which one is the problem since I can access the WEBGUI just fine. Just anything on the internet stops working. May try the next version to see if it works and if I can access the modem information webgui.
I just installed the new 4 port Realtek card and everything is working fine. I did a full install and reactivation using this version. I am getting great speeds connected to my GL.Inet Flint 2 as an AP connected to my X86-64 system connected to 1 gig cable modem. Now I am going to install a single 2.5 GBPS card in my home server and see how it performs.
Ok I will have to try resetting to defaults and redo all settings to see if it works for me on the latest build. That is just weird that nothing works for me once I upgrade to newer builds.
