Posted: Sun Feb 02, 2025 18:16 Post subject: New Build - 02/02/2025 - r59468
Welcome to Broadcom r59468 beta release thread for reporting, feedback to developers & community benefit.
Please do not flash builds until installation is understood, risks involved and device specificrecovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.
CLI Flash: 'cd /tmp' then 'wget {file URL}' (httponly) or 'curl -O {file URL}' (http, https, ftp) 'write {file} linux' then 'reboot'.
Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!
Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Debug Analyze: stracetcpdump.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.
Joined: 16 Nov 2015 Posts: 6778 Location: UK, London, just across the river..
Posted: Sun Feb 02, 2025 19:58 Post subject:
Router Model Netgear R7000
Firmware Version DD-WRT v3.0-r59468 std (02/02/25)
Kernel Version Linux 4.4.302-rt232-st60 #12946 SMP Fri Jan 31 04:02:32 +07 2025 armv7l
update: CLI r59429> r59468
reset: NO
mode: Gateway/DNScrypt-proxy V2 via Entware, AD-Block (via DNSmasq script and via DNScrypt block file),IPset Firewall,Forced DNS,AP&Net Isolation,x3VLAN,VPN client(PBR),40 HT 2.4Ghz only, Disable 121
status: Operational 2h+
errors: Nothing new, yet, no time for deep testing...still dont see any traffic at, access restrictions, counter stays at 0...Thanks BS and Team ! _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 58184 WAP
TP-Link WR1043NDv2 -DD-WRT 59369 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 59369 Gateway/DoT,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 59468 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 59369 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Dynalink DL-WRX36-DDWRT 59369
Broadcom
Netgear R7000 --DD-WRT 59468 Gateway/DNScrypt-proxy2/AD-Block,IPset Firewall,Forced DNS,x4VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Posted: Sun Feb 02, 2025 20:41 Post subject: AC87U
Router/Version: Asus RT-AC87U R
Update method: WebUpgrade
File/Kernel: asus_rt-ac87u-firmware.trx_r59468 std / Linux 4.4.302-rt232-st60 #12954 SMP Sun Feb 2 03:53:31 +07 2025 armv7l
Previous/Reset: r59429 / no
Mode/Status: Gateway, Open VPN Client / Up and running for 2:19 hours
CPU Temperature: CPU 58.2 °C / WL0 38.0 °C / WL1 0.0 °C (ambient temperature 18.0 °C)
Issues/Errors: no
As always, the Quantenna chip has its own quirks. This is a closed source chipset
There is no way to install a channel.
But you can disable 5.0 GHz. @mpgalaxy hack "If you set the radio mode to station bridge and disable the network mode, the 5GHz device will turn off completely even after reboot."
If your router's light turns red, don't worry. Internet connection is ok.
Thank you BS and gurus! _________________ Atheros
Netgear XR500 Nighthawk - DD-WRT 59468
Tp-Link TL-WDR4900 v1.3 - DD-WRT 53133
TP-Link WR1043ND v4 - DD-WRT 51838
TP-Link WR1043ND v2 - Gargoyle OS 1.13.0
TP-Link WR841ND v11 - DD-WRT 59468
Broadcom
Asus RT-AC87U R - DD-WRT 59468
Asus RT-N66U - DD-WRT 59468
Linksys WRT54GL v1.1 - DD-WRT 54517M
Linksys WRT54GL v1.1 - FreshTomato 2023.4_MIPS_K26
Linksys WRT54GL v1.1 - Gargoyle OS 1.6.2
Joined: 18 Mar 2014 Posts: 13532 Location: Netherlands
Posted: Mon Feb 03, 2025 7:53 Post subject:
Router Model: Linksys EA6900 (XVortex CFE)
Firmware Version: Firmware by egc: DD-WRT v3.0-r59468M Community Build (02/02/25)
Kernel Version: Linux 4.4.302-rt232-st60 #1 SMP Sun Feb 2 09:57:09 CET 2025 armv7l
Upgraded from Firmware by egc: DD-WRT v3.0-r59302M Community Build (01/22/25) using patched build so GUI update is working, without a problem for this Xvortex CFE upgrade 😃
Build is available and has a number of goodies like ipset for Wireguard and SMCroute for multicast routing so that you can see your DLNA media server also from other subnets
Reset: No not this time.
Configuration: Default gateway mode, 2,4GHz wireless running with unbridged VAP, 5GHz running, some static leases and some port range forwarding.
Four WireGuard tunnels running, one Server, one site-to-site and two clients in Fail-over group to Mullvad (of course with PBR to allow the WG server to use the WAN).
OpenVPN client with PBR running.
DDNS (dynv6) working.
SMCRoute working
IPv6 working.
CTF&FA Enabled
NVRAM size 56K (NVRAM size should not be a problem with the Xvortex CFE)
Router/Version: Asus RT-AC66U
File/Kernel: DD-WRT v3.0-r59468 giga (02/02/25) / Linux 4.4.302-rt232-st60 #35468 Sun Feb 2 03:54:54 +07 2025 mips
Previous/Reset: Yes, reset to factory defaults via GUI
Mode/Status: Gateway with smartDNS. Router is in double NAT. SSH enabled / Telnet disabled. WIFI disabled. Logging enabled.
Issues/Errors: Yes
CTF works when set via GUI using Save ---> Apply, however, upon reboot (power cycle), it no longer works. Just by chance, I discovered that if you power cycle with the LAN cable disconnected, CTF works as it should. This appears to be 100% repeatable; Power cycling with LAN cable connected = CTF not working and power cycling with LAN cable disconnected = CTF working. I've attached logs with both CTF and SFE with and without LAN cable connected for comparison. Please note that SFE works as it should with and without LAN cable connected and WAN cable stays connected for all tests.
And just a general observation: When making changes, a majority of setting changes will only stick if you also use the "Apply Settings" button, Save and then Reboot does not work.
Thanks to BS and everyone else involved.
(build 59468) - Setup.png
Description:
DD-WRT WAN setup page
Filesize:
91.79 KB
Viewed:
557 Time(s)
r59468 Logs.rar
Description:
'dmesg' & 'cat /tmp/var/log/messages' CTF & SFE logs to compare with LAN cables connected and disconnected.
Router/Version: Asus RT-N66U
Update method: WebUpgrade
File/Kernel: dd-wrt.v24-59468_NEWD-2_K3.x-big-RT-N66U.trx / Linux 4.4.302-rt232-st60 #35484 Sun Feb 2 04:17:15 +07 2025 mips
Previous/Reset: 59429 / no
Mode/Status: Gateway, Open VPN Client / Up and running for 3:51 hours
CPU Temperature: WL0 46.0 °C (ambient temperature 20.0 °C)
Issues/Errors:yes
MAC address cloning does not work, web interface does not respond on the cloning page /WanMAC.asp
For a long time it is not possible to connect to the web interface _________________ Atheros
Netgear XR500 Nighthawk - DD-WRT 59468
Tp-Link TL-WDR4900 v1.3 - DD-WRT 53133
TP-Link WR1043ND v4 - DD-WRT 51838
TP-Link WR1043ND v2 - Gargoyle OS 1.13.0
TP-Link WR841ND v11 - DD-WRT 59468
Broadcom
Asus RT-AC87U R - DD-WRT 59468
Asus RT-N66U - DD-WRT 59468
Linksys WRT54GL v1.1 - DD-WRT 54517M
Linksys WRT54GL v1.1 - FreshTomato 2023.4_MIPS_K26
Linksys WRT54GL v1.1 - Gargoyle OS 1.6.2
Posted: Wed Feb 05, 2025 16:53 Post subject: Re: N66U
KACTET wrote:
MAC address cloning does not work, web interface does not respond on the cloning page /WanMAC.asp
For a long time it is not possible to connect to the web interface
I also can confirm that this is an issue for the Asus RT-AC66U firmware.
Joined: 16 Mar 2019 Posts: 355 Location: Szczecin, Poland EU
Posted: Thu Feb 06, 2025 23:23 Post subject:
Router: Linksys EA6400
Update method: Initial flash from OEM by files "flash_to_ddwrt" from Tomato project and update via GUI to newest beta build
File/Kernel: Linux 4.4.302-rt232-st60 #12946 SMP Fri Jan 31 04:02:32 +07 2025 armv7l
Previous/Reset: Previously oem firmware was here
Mode/Status: Internet gateway, WIFI 5GHz AP (AC mode), dnsmasq server, iptables firewall, SSHd
I'm replace old WDR3600 with that Linksys / Cisco model. On WDR3600 in newest build it was <- 300 mbit /s wan performance. On this "new" router is ~615 mbit/s. (I have 600 mbit+ plan from my ISP). My device working rather good. I have 1 PC connected by cord and 2 stations for 5GHz WIFI. Generic scores are satisfactory. Naturally I need to use CTF feature for increase transfers. Without this solutions I have only 250 - 280 mbit/s download on WAN. It's rather weak result... Device have 2 cores CPU and 128 RAM. I believe it can working better. I think I'm changed device for better model than I had earlier.
Joined: 16 Nov 2015 Posts: 6778 Location: UK, London, just across the river..
Posted: Fri Feb 07, 2025 11:45 Post subject:
thommy181 wrote:
....Linksys EA6400 Naturally I need to use CTF feature for increase transfers. Without this solutions I have only 250 - 280 mbit/s download on WAN. It's rather weak result... Device have 2 cores CPU and 128 RAM. I believe it can working better. I think I'm changed device for better model than I had earlier.
...
with 2 cores at 800Mghz that's how far this device could go 250-300 Mbit without CTF is normal...
my R7000 that has dual core @ 1Ghz can do 300-400 Mbit without CTF...and yes for better results you'd need CTF - enabled ...check if you have FA & CTF on it may need a restart to appear... _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 58184 WAP
TP-Link WR1043NDv2 -DD-WRT 59369 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear XR500 --DD-WRT 59369 Gateway/DoT,Forced DNS,AP Isolation,4VLAN,Ad-Block,Firewall,Vanilla
Netgear R7800 --DD-WRT 59468 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 59369 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Dynalink DL-WRX36-DDWRT 59369
Broadcom
Netgear R7000 --DD-WRT 59468 Gateway/DNScrypt-proxy2/AD-Block,IPset Firewall,Forced DNS,x4VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Joined: 16 Mar 2019 Posts: 355 Location: Szczecin, Poland EU
Posted: Fri Feb 07, 2025 14:06 Post subject:
I don't see flow acceleration options for my model. In the WDR3600 it was this feature, but it not increase transfers. My currently score with CTF enabled and force gigabit mode on LAN. I probably won't have higher score when I have 600+ option from ISP. 612 is 600+.
Joined: 02 Jan 2015 Posts: 85 Location: Gdansk, Poland
Posted: Fri Feb 07, 2025 21:51 Post subject: Re: N66U
KACTET wrote:
Router/Version: Asus RT-N66U
Update method: WebUpgrade
File/Kernel: dd-wrt.v24-59468_NEWD-2_K3.x-big-RT-N66U.trx / Linux 4.4.302-rt232-st60 #35484 Sun Feb 2 04:17:15 +07 2025 mips
Previous/Reset: 59429 / no
Mode/Status: Gateway, Open VPN Client / Up and running for 3:51 hours
CPU Temperature: WL0 46.0 °C (ambient temperature 20.0 °C)
Issues/Errors:yes
MAC address cloning does not work, web interface does not respond on the cloning page /WanMAC.asp
For a long time it is not possible to connect to the web interface
Same on EA6900.
After few low level hard reset it's strat working - maybe huge changes in configuration files? _________________ EA6900 r57956
WRT600N r57956
Joined: 02 Jan 2015 Posts: 85 Location: Gdansk, Poland
Posted: Fri Feb 07, 2025 21:55 Post subject:
thommy181 wrote:
I don't see flow acceleration options for my model. In the WDR3600 it was this feature, but it not increase transfers. My currently score with CTF enabled and force gigabit mode on LAN. I probably won't have higher score when I have 600+ option from ISP. 612 is 600+.
similar, low lever reset in few times at row, solve this.
Reset from web interface don't clear all data. for me helps reset from cfe miniserver and hard reset.
after that, I restore my regular settings from backup and router start working.
P.S.
some times reset from gui are not possible - gui crash before reset after press apply.
Connection through telnet or SSH are not possible too, because after first uncompleted reset port are closed. _________________ EA6900 r57956
WRT600N r57956