Joined: 16 Nov 2015 Posts: 6177 Location: UK, London, just across the river..
Posted: Sun Nov 19, 2023 4:31 Post subject:
I dont have such an issues..but if you need help you have to give us details about your set up...
pic's preferred..
Otherwsie
-i dont use QoS
-i dont use SFE
-i dont use the ondemand script anymore..
-i dont have/use samba
-i dont use 5GHZ radio at all, if you use it make sure you set a valid channel (im on vanilla radio drivers)
-if you use VPN that doesent provide dco, than you have to remove dco - add to advanced vpn config box disable-dco
-check your PSU power adapter..
I have a 100Mbit/s and another one 200Mbit/s Internet subscription. _________________ Atheros
TP-Link WR740Nv1 ---DD-WRT 53045 WAP
TP-Link WR1043NDv2 -DD-WRT 54248 Gateway/DoT,Forced DNS,AP Isolation,Ad-Block,Firewall,VPN,x1VLAN
TP-Link WR1043NDv2 -DD-WRT 54079 Gateway/DoT,Forced DNS,Ad-Block,Firewall,x4VLAN,VPN
TP-Link WR1043NDv2 -Gargoyle OS 1.15.x AP,DNS,QoS,Quotas
Qualcomm-Atheros
Netgear R7800 --DD-WRT 54248 Gateway/DoT,AD-Block,Forced DNS,AP&Net Isolation,x3VLAN,Firewall,Vanilla
Netgear R9000 --DD-WRT 54079 Gateway/DoT,AD-Block,AP Isolation,Firewall,Forced DNS,x2VLAN,Vanilla
Broadcom
Netgear R7000 --DD-WRT 54079 Gateway/SmartDNS/DoH,AD-Block,Firewall,Forced DNS,x3VLAN,VPN
NOT USING 5Ghz ANYWHERE
------------------------------------------------------
Stubby DNS over TLS I DNSCrypt v2 by mac913
Last edited by Alozaros on Sun Nov 19, 2023 12:44; edited 3 times in total
Joined: 13 Aug 2013 Posts: 6818 Location: Romerike, Norway
Posted: Sun Nov 19, 2023 10:05 Post subject:
Mine have been stable for years. Upgraded to a build with kernel 6. Had reboot once. Upgraded to new build with K6.1 and have not experienced any reboots.
SFE is off. I only have a 100Mbit/s Internet subscription.
Do you set your static leases in the dnsmasq additional config?
Static leases were there months back but not anymore. That is something I need to ask later on after I get router in a stable condition w/latest updates.
So answer is No static leases.
Thanks,
Last edited by nkaufman on Sun Nov 19, 2023 15:49; edited 1 time in total
What I'm trying to convey here is that router works fine on older r53544 build of 9/28
So settings might not be an issue unless there is some setting that newer versions need to be set a specific value.
I dont have such an issues..
-i dont use QoS
-i dont use SFE
-i dont use the ondemand script anymore..
-i dont have/use samba
-i dont use 5GHZ radio at all, if you use it make sure you set a valid channel (im on vanilla radio drivers)
-if you use VPN that doesent provide dco, than you have to remove dco - add to advanced vpn config box disable-dco
-check your PSU power adapter..
I have a 100Mbit/s and another one 200Mbit/s Internet subscription.
I have 1Gb service and 2.4GHz has never worked well on R7800. That is perhaps a discussion for another post so as to not get distracted from the issue at hand.
Will definitely post more details on 2.4GHz once I get latest version up and running smoothly
What I'm trying to convey here is that router works fine on older r53544 build of 9/28
So settings might not be an issue unless there is some setting that newer versions need to be set a specific value.
No need to convey anything.
53544 was before the Major upgrade from Kernel 4.9 to 6.1.
53562 was the last public K4.9 so it and all before are water under the bridge now.
Gone back to 53544 (9/28 build) which I had installed before going to 53843 and no router reboots now, it works fine.
I do see SFE enabled under Setup->Basic Setup in current build of 53544 of 9/28
Any suggestions?
Thank you.
Same issues here !
After updated to r53939 the problems began and a upgrade to r54079 did not helped either.
r53843 was working fine here and I guess I have to downgrade to that one to get the issues solved. _________________ Regards,
Vaako
1x Netgear R7800 Nighthawk - firmware not decided yet !!!!
1x Netgear R7000 Nighthawk r36410
1x Ubiquiti RouterStation Pro DD-WRT r23204 std (12/24/13)
1x Asus RT-N16 SVN revision 20675 NEWD-2 K2.6
1x Linksys E4200 v3.0 r34777 mega (01/31/18 )
1x Buffalo WZR-HP-G300NH B0 B0 Gargoyle FW
1x Linksys WRT600N v1.1 (Bricked)
1x Linksys WRT54GL v1.1 (DD-WRT 26446)
1x Linksys WRT54GS v2.2 (DD-WRT 26446)
1x Linksys RVS4000 (stock fw)
3x D-Link DWL-7100AP (openWRT)
2x TP-Link TL-WA801ND (Bridge mode) 100mW TX-Power
Asus WL-520GU SVN 16403M NEWD-2 Eko std-nokaid
4x Fonera with Gargoyle FW
Mine have been stable for years. Upgraded to a build with kernel 6. Had reboot once. Upgraded to new build with K6.1 and have not experienced any reboots.
SFE is off. I only have a 100Mbit/s Internet subscription.
How did you do the upgrade to the newer kernel 6, totally fresh install and reconfigured the router settings or an upgrade from an 4.1 kernel build and keep all settings as they where ? _________________ Regards,
Vaako
1x Netgear R7800 Nighthawk - firmware not decided yet !!!!
1x Netgear R7000 Nighthawk r36410
1x Ubiquiti RouterStation Pro DD-WRT r23204 std (12/24/13)
1x Asus RT-N16 SVN revision 20675 NEWD-2 K2.6
1x Linksys E4200 v3.0 r34777 mega (01/31/18 )
1x Buffalo WZR-HP-G300NH B0 B0 Gargoyle FW
1x Linksys WRT600N v1.1 (Bricked)
1x Linksys WRT54GL v1.1 (DD-WRT 26446)
1x Linksys WRT54GS v2.2 (DD-WRT 26446)
1x Linksys RVS4000 (stock fw)
3x D-Link DWL-7100AP (openWRT)
2x TP-Link TL-WA801ND (Bridge mode) 100mW TX-Power
Asus WL-520GU SVN 16403M NEWD-2 Eko std-nokaid
4x Fonera with Gargoyle FW
Joined: 18 Mar 2014 Posts: 12451 Location: Netherlands
Posted: Tue Nov 21, 2023 6:36 Post subject:
Problem is that performance (WAN<>LAN throughput, WireGuard etc ) is below par with Kernel 6.1.
without SFE you will not get more than 550 Mb/s which used to be 900 Mb/s
