[blkt]

Welcome to Marvell r53544 beta release thread for reporting, feedback to developers and community benefit.
Please do not flash builds until installation is understood, risks involved and device specific recovery methods.
Avoid discussions, create threads for questions, general problems or use search; this thread is not for support.
List router model & version or revision, operating & wireless modes & exact filename/firmware image flashed.

CLI Flash: 'cd /tmp' then 'wget {file URL}' (http only) or 'curl -O {file URL}' (http, https, ftp) 'write {file} linux' then 'reboot'.

Downloads: HTTPS, FTP

Trac SVN: repository since last build 53469 (mirror)

• OpenVPN 2.6.6: Changelog, Guides, Server, PBR, DNS, Kill Switch, Watchdog, Reverse PBR, Client, Multiple, tips & scripts.
• WireGuard 1.0.20211208/Tools: Changelog, Guides, Client, Server, Adv, PBR, KS, tips & scripts. Thanks BS egc & eibgrad!

Notes:
• PHP ReadyMedia ZFS reboot RAID firewall WG IOzone fix rtl815 Transmission x86 firewall nDPI ar531x iperf3 IPv6 WG x86
• PowerTOP Plex nDPI flashrom FRR Zabbix MT7621 Tor OpenSSL nDPI 4.14 Unbound SmartDNS common ZFS In-a-Dyn 6.1
• DC nDPI QoS Squid ZFS Transmission DNSCrypt DC DW02-412H iperf3 Tor BOINC MC APFS mDNS/Avahi DC 4.14 Plex 6.1

Issues, observations, and/or workarounds reported:
• WebUI: Clear history or use a portable. Temporary cache bypass: Ctrl+F5, Cmd+Shift+R or new private window/incognito.
• Please report findings with steps needed to reproduce, configuration, clients, output, logs and important information below!

Important:
• Detail issues & relevant configs, logs: syslog klog 'dmesg' 'cat /tmp/var/log/messages' nvram set console_debug=1, serial.
• Firewall NAT: 'iptables -vnL' 'iptables -t nat -vnL' 'iptables -t mangle -vnL' & 'cat /tmp/.ipt'. Debug Analyze: strace tcpdump.
• Gremlins: reboot. cold boot. Reset & reconfigure not restore backup. Search Trac & discuss in forum before opening tickets.
• Include operating & wireless modes (e.g. Gateway, Router, AP, SB, WDS, Mesh) and applicable configurations to reproduce.

Example Template:

[oliver44]

Router Model Linksys WRT1900ACS v2
Firmware VersionDD-WRT v3.0-r53544 std (09/28/23)
Kernel Version Linux 4.9.337 #3999 SMP Thu Sep 28 04:18:50 +07 2023 armv7l
Current Time Thu, 28 Sep 2023 21:26:53
Uptime 2:20

update-browser waterfox, I switched from r53469 with keeping the settings, all ok

connection Type PPPoE - IPv6 Type DHCPv6 with Prefix Delegation 1Gbps
IPv6 Type DHCPv6 with Prefix Delegation-On - all Ok

Operating Mode Gateway/AP
Shortcut Forwarding Engine-On
Schedule Reboot-On,
Web Access Protocol - HTTPS,
SSH (public key)-all ok
Encrypt DNS Enable
Validate DNS Replies (DNSSEC)-all ok
Port Forwarding - all Ok,
USB - System Log -all Ok
Schedule Reboot - At a Set Time - On


Wireless Interface 5GHz-Wireless Mode AP-Wireless Network Mode-AC, Width VHT 80 Mhz-Wireless Channel-36,Extension Channel UU, Short GI, Short Preamble, Single User Beamforming, Radio Scheduling, TX Power-30dBm ,TX Antenna Chains-1+2+3+4, RX Antenna Chains-1+2+3+4, Enable-WPA2 - WPA3 Personal / SAE-CCMP-128 (AES), Regulatory Domain Romania, all-ok

Wireless Interface 2.4GHz-Wireless Mode AP-Wireless Network Mode-N, Width VHT 40 Mhz-Wireless Channel-11, Extension Channel Lower, Short Preamble, Short GI, Radio Scheduling,TX Power-30dBm ,TX Antenna Chains-1+2+3+4, RX Antenna Chains1+2+3+4, Enable-WPA2 - WPA3 Personal / SAE-CCMP-128 (AES) all-ok!

[Wizo]

Router/Version: Linksys WRT1900ACS v2
File/Kernel: Linux 4.9.337 #3999 SMP Thu Sep 28 04:18:50 +07 2023 armv7l
Previous/Reset: DD-WRT v3.0-r53469 std (09/08/23)/ No
Mode/Status: Gateway, SFE (enabled), Access Point 802.11ac, WireGuard-VPN / Uptime 2 hours ish.
Issues/Errors: None so far, Will edit if found.

I switched from r53469 with keeping the settings, all ok

connection Type Automatic config - DHCP
IPv6 Off
UPnP On
Operating Mode Gateway/AP
Shortcut Forwarding Engine-On
Web Access Protocol - HTTP,
SSH (public key)
Wireguard VPN (Surfshark)

Wireless Interface 5GHz-Wireless Mode AP-Wireless Network Mode-AC / N, Width VHT 80 Mhz-Wireless Channel-36,Extension Channel UU+6, Short GI, Short Preamble, Single User Beamforming, Radio Scheduling, TX Power-30dBm ,TX Antenna Chains-1+2+3+4, RX Antenna Chains-1+2+3+4, Enable-WPA2 - WPA3 Personal / SAE-CCMP-128 (AES), Regulatory Domain UK.

Wireless Interface 2.4GHz-Wireless Mode AP-Wireless Network Mode-Mixed, Width VHT 40 Mhz-Wireless Channel-11, Extension Channel Lower, Short Preamble, Short GI, Radio Scheduling,TX Power-30dBm ,TX Antenna Chains-1+2+3+4, RX Antenna Chains1+2+3+4, Enable-WPA2 - WPA3 Personal / SAE-CCMP-128 (AES) , TurboQAM (QAM256)

Thank you for your ongoing support.

[oliver44]

after 4 days of operation 5GHZ WPA2/WPA3 no longer wants to connect, very strange this morning I found in the system log!

[dale_gribble39]

Pretty sure you were already advised not to mix WPA2 and WPA3.