WRT3200-ACM-Firmware-Upgrade

Post new topic   Reply to topic    DD-WRT Forum Index -> Marvell MVEBU based Hardware (WRT1900AC etc.)
Author Message
Razan
DD-WRT Novice


Joined: 06 Jan 2022
Posts: 14

PostPosted: Sat Sep 23, 2023 17:21    Post subject: WRT3200-ACM-Firmware-Upgrade Reply with quote
Hello Community,

I contact you because I have some interrogation before upgrading my WRT3200-ACM to new firmware without loosing my fresh configuration.

I read this topic : https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=311117
It explained that if I don't want to loose my configuration, I need connect via SSH / Telnet to identify my current partition in use before upgrading through GUI.

I also found this other link : https://wiki.dd-wrt.com/wiki/index.php/Installation
It is explained that before and after an upgrade, I need to restore the router to defaults with the reset button (30/30/30 ? or 30/30 ?)

So, regarding these different instructions, I contact you to get some light on my fog to use the best method.

Thank you mates

::RAZAN::
Sponsor
egc
DD-WRT Guru


Joined: 18 Mar 2014
Posts: 12507
Location: Netherlands

PostPosted: Sat Sep 23, 2023 17:40    Post subject: Reply with quote
Moved to the appropriate forum.

Please read the forum guidelines:
https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=324087

_________________
Routers:Netgear R7000, R6400v1, R6400v2, EA6900 (XvortexCFE), E2000, E1200v1, WRT54GS v1.
Install guide R6400v2, R6700v3,XR300:https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=316399
Install guide R7800/XR500: https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=320614
Forum Guide Lines (important read):https://forum.dd-wrt.com/phpBB2/viewtopic.php?t=324087
Razan
DD-WRT Novice


Joined: 06 Jan 2022
Posts: 14

PostPosted: Sat Sep 23, 2023 17:48    Post subject: Reply with quote
Hi,

I will read forums rules.

Just, to which link did you move the post please ?

Thank you

::RAZAN::
dale_gribble39
DD-WRT Guru


Joined: 11 Jun 2022
Posts: 1638

PostPosted: Sat Sep 23, 2023 19:32    Post subject: Reply with quote
The nvram is shared. No worry of losing your configuration. But it is not recommended to keep stock firmware on the other partition. We've kept the same configuration on the one currently in the hotseat here without having to do all that nonsense.
_________________
"The woods are lovely, dark and deep,
But I have promises to keep,
And miles to go before I sleep,
And miles to go before I sleep." - Robert Frost

"I am one of the noticeable ones - notice me" - Dale Frances McKenzie Bozzio

<fact>code knows no gender</fact>

This is me, knowing I've ruffled your feathers, and not giving a ****
Some people are still hard-headed.

--------------------------------------
Mac Pro (Mid 2012) - Two 2.4GHz 6-Core Intel Xeon E5645 processors 64GB 1333MHz DDR3 ECC SDRAM OpenSUSE Leap 15.5
SurprisedItWorks
DD-WRT Guru


Joined: 04 Aug 2018
Posts: 1428
Location: Appalachian mountains, USA

PostPosted: Mon Sep 25, 2023 16:23    Post subject: Reply with quote
If you want to keep your configuration through an upgrade, DO NO RESETS because "reset" in dd-wrt refers to resetting the configuration to default for the currently installed firmware. Just do a backup (backs up the configuration) first, for safety, and do the upgrade in dd-wrt using the webflash.bin file, and everything should work out fine.

The WRTxxxx routers have dual firmware partitions in memory. You boot from one, and upgrades load into the other by default, with the boot partition automatically changed to the new one. So if you just upgrade routinely without special tricks, you hop between memory partitions on subsequent upgrades. The special tricks you read about are to suppress the "hopping" and upgrading into the current boot partition, a special situation that will not normally apply.

HOWEVER, do not try this as a way to jump over many, many intermediate builds. If you are jumping more than a year in firmware release dates, you should consider resetting after the upgrade followed by re-entering your configuration by hand. The configuration as stored is a long list of names and values of variables that dd-wrt stores in nvram (one nvram area shared across two firmware partitions, in the case of your router model). Over a long period of time variable names in use can be changed by the developers, and you can find that using an old configuration leads to trouble. A very few years ago, the names of the wifi interfaces changed for the Linksys WRTxxxx models, and that broke everything. We all had to rebuild configs from scratch.

I've seen many times also that the 30/30/30 reset should not be done with the WRTxxxx routers, that it's actually dangerous. I don't know why. But apparently the 30/30/30 thing was for very early routers that are not around anymore. Yes, the dd-wrt wiki has old articles that mislead, and worse, none of them have dates on them!

_________________
2x Netgear XR500 and 3x Linksys WRT1900ACSv2 on 53544: VLANs, VAPs, NAS, station mode, OpenVPN client (AirVPN), wireguard server (AirVPN port forward) and clients (AzireVPN, AirVPN, private), 3 DNSCrypt providers via VPN.
Display posts from previous:    Page 1 of 1
Post new topic   Reply to topic    DD-WRT Forum Index -> Marvell MVEBU based Hardware (WRT1900AC etc.) All times are GMT

Navigation

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum