zarkmughal DD-WRT Novice
Joined: 05 Feb 2023 Posts: 33
|
Posted: Sat Apr 08, 2023 18:55 Post subject: TP-LINK TL-MR3620 (EU) V1.0 - NEEDS DD-WRT SUPPORT. |
|
NEEDS DD-WRT SUPPORT FOR TP-LINK TL-MR3620 (EU) V1.0
(AC1350 3G/4G WIRELESS DUAL BAND ROUTER)
JUST DISASSEMBLED THE DEVICE, REMOVED RF SHIELD.
SOC IS QUALCOM ATHEROS QCA9561
16MB FLASH (DIFFICULT TO APPROACH WITH A SOP8/SOIC8 TEST CLIP & PROGRAMMER)
128 MB RAM (SPECS SEAMS SIMILAR TO ARCHER C59)
1X USB 2.0
2ND RADIO CHIP WAS COVERED WITH STICK-ON HEATSINK, SO I DIDN'T REMOVED THAT.
UNFORTUNATELY, TX & RX ARE NOT CONNECTED TO THE UART TERMINALS,
TP4 WILL BE TX (CONFIRMED WITH MULTIMETER 2.5V-2.9V VARYING)
TP5 WILL BE RX (0V)
(X VALUE RESISTORS ARE MISSING - CAN BE CONNECTED WITH A SOLDER BLOB OR 0-OHM)
& WILL NEED THIN JUMPER WIRE TO THE UART TERMINAL WHICH ARE NOT CONNECTED (NC).
THERE IS AN IC 74HC595 WHICH I AM NOT FAMILIAR WITH. (ANYONE CAN COMMENT ON ITS FUNCTION PLEASE).
I HAVE SAVED THE BOOT-LOG AS BELOW. FROM TP4 (TX)
U-BOOT IS ON WEIRD BAUD RATE 120000 (SIMILAR TO TL-WR941N (CN) V6) (OTHERWISE SHOWS GARBLED CHARACTERS)
KERNAL IS ON 115200
REST OF THE SETTING ARE SAME AS OTHER TP-LINK DEVICES. USING PUTTY (LATEST)
PLEASE GUIDE ME, CAN I DUMP/COPY ITS FULL FLASH DUMP FILE WHILE ON STOCK FIRMAWRE USING SSC/SSH??? (FOR BACKUP REASON TOO, MOST IMPORTANTLY. BEFORE TRYING TESTFILE) SO I CAN SHARE IT HERE TOO.
REQUEST TO BRAINSLAYER, FOR DEVICE SUPPORT.
Code: |
U-Boot 1.1.4-gff2db3d2-dirty (Feb 27 2018 - 15:59:11)
ap151 - Dragonfly 1.0
TP-Link Archer MR400
DRAM: 128 MB
Top of RAM usable for U-Boot at: 88000000
Reserving 120k for U-Boot at: 87fe0000
Reserving 32832k for malloc() at: 85fd0000
Reserving 44 Bytes for Board Info at: 85fcffd4
Reserving 36 Bytes for Global Data at: 85fcffb0
Reserving 128k for boot params() at: 85faffb0
Stack Pointer at: 85faff98
Now running in RAM - U-Boot at: 87fe0000
Flash Manuf Id 0xef, DeviceId0 0x40, DeviceId1 0x18
flash size 16MB, sector count = 256
Flash: 16 MB
Using default environment
ath_gmac_enet_initialize: reset mask:c02200
Dragonfly----> S27 PHY *
: cfg1 0x80000000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
eth0 up
ATHRS27: resetting s27
ATHRS27: s27 reset done
: cfg1 0x800c0000 cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :50
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :50
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :50
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :50
eth1 up
eth0, eth1
Setting 0x181162c0 to 0x82
Autobooting in 1 seconds
do_bootm:argc=2, addr=0x9f020000
## Booting image at 9f020000 ...
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 8030d7b0) ...
## Giving linux memsize in bytes, 134217728
Starting kernel ...
|
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
Code: |
console [ttyS0] enabled, bootconsole disabled
[ 0.650000] console [ttyS0] enabled, bootconsole disabled
[ 0.660000] loop: module loaded
[ 0.660000] m25p80 spi0.0: found w25q128, expected m25p80
[ 0.670000] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 0.680000] 7 cmdlinepart partitions found on MTD device spi0.0
[ 0.680000] Creating 7 MTD partitions on "spi0.0":
[ 0.690000] 0x000000000000-0x000000020000 : "boot"
[ 0.690000] 0x000000020000-0x000000160000 : "kernel"
[ 0.700000] 0x000000160000-0x000000fc0000 : "rootfs"
[ 0.710000] mtd: partition "rootfs" set to be root filesystem
[ 0.710000] 0x000000fc0000-0x000000fd0000 : "config"
[ 0.720000] 0x000000fd0000-0x000000fe0000 : "romfile"
[ 0.720000] 0x000000fe0000-0x000000ff0000 : "rom"
[ 0.730000] 0x000000ff0000-0x000001000000 : "radio"
[ 0.740000] Register flash device:flash0
[ 0.740000] flash_chrdev : flash_chrdev_init
[ 0.750000] tun: Universal TUN/TAP device driver, 1.6
[ 0.750000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.780000] ag71xx_mdio: probed
[ 0.900000] ag71xx_mdio: probed
[ 0.910000] spiflash_ioctl_read, Read from 0x00fcf100 length 0x6, ret 0, retlen 0x6
[ 0.920000] read mac from flash(0xFCF100): 70-4F-57-42-14-9D
[ 0.920000] eth0: Atheros AG71xx at 0xba000000, irq 5
[ 1.480000] eth0: Found an AR934X built-in switch 5
[ 2.510000] eth1: Atheros AG71xx at 0xb9000000, irq 4
[ 3.070000] ag71xx ag71xx.0: eth1: connected to PHY at ag71xx-mdio.1:00 [uid=004dd042, driver=Generic PHY]
[ 3.080000] eth1 : connected to PHY at ag71xx-mdio.1:00 [uid=004dd042, driver=Generic PHY]
[ 3.090000] PPP generic driver version 2.4.2
[ 3.090000] NET: Registered protocol family 24
[ 3.090000] Mirror/redirect action on
[ 3.100000] u32 classifier
[ 3.100000] Actions configured
[ 3.110000] Netfilter messages via NETLINK v0.30.
[ 3.110000] nf_conntrack version 0.5.0 (1962 buckets, 7848 max)
[ 3.120000] GRE over IPv4 demultiplexor driver
[ 3.120000] GRE over IPv4 tunneling driver
[ 3.130000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 3.130000] TCP cubic registered
[ 3.140000] NET: Registered protocol family 10
[ 3.140000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 3.150000] IPv6 over IPv4 tunneling driver
[ 3.160000] NET: Registered protocol family 17
[ 3.160000] NET: Registered protocol family 15
[ 3.160000] Ebtables v2.0 registered
[ 3.170000] 8021q: 802.1Q VLAN Support v1.8
[ 3.170000] ### of_selftest(): No testcase data in device tree; not running tests
[ 3.190000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 3.190000] Freeing unused kernel memory: 200k freed
starting pid 431, tty '': '/etc/init.d/rcS'
[ 4.130000] SCSI subsystem initialized
[ 4.600000] usbcore: registered new interface driver usbfs
[ 4.620000] usbcore: registered new interface driver hub
[ 4.660000] usbcore: registered new device driver usb
[ 4.710000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.720000] ehci-platform ehci-platform.0: Generic Platform EHCI Controller
[ 4.730000] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[ 4.770000] ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000
[ 4.790000] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
[ 4.800000] hub 1-0:1.0: USB hub found
[ 4.800000] hub 1-0:1.0: 1 port detected
[ 4.800000] ehci-platform ehci-platform.1: Generic Platform EHCI Controller
[ 4.810000] ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2
[ 4.850000] ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000
[ 4.870000] ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00
[ 4.870000] hub 2-0:1.0: USB hub found
[ 4.880000] hub 2-0:1.0: 1 port detected
[ 4.910000] Initializing USB Mass Storage driver...
[ 4.910000] usbcore: registered new interface driver usb-storage
[ 4.920000] USB Mass Storage support registered.
[ 5.150000] dns_init
[ 5.150000] domain_name:tplinkwifi.net
[ 5.170000] L2TP core driver, V2.0
[ 5.190000] PPPoL2TP kernel driver, V2.0
Please press Enter to activate this console. [err] syslogd[main --763] syslogd : syslogd_init
[ dm_readFile ] 2042: can not open xml file /var/tmp/pc/reduced_data_model.xml!, about to open file /etc/reduced_data_model.xml
[ 6.820000] spiflash_ioctl_read, Read from 0x00fd0000 length 0x10000, ret 0, retlen 0x10000
[ 6.850000] spiflash_ioctl_read, Read from 0x00fd0000 length 0x7f64, ret 0, retlen 0x7f64
[ 6.890000] spiflash_ioctl_read, Read from 0x00fd0000 length 0x10000, ret 0, retlen 0x10000
[ 6.920000] spiflash_ioctl_read, Read from 0x00fd0000 length 0x7f64, ret 0, retlen 0x7f64
[ 6.950000] spiflash_ioctl_read, Read from 0x00fcf400 length 0x29, ret 0, retlen 0x29
[ 6.950000] spiflash_ioctl_read, Read from 0x00fcf100 length 0x6, ret 0, retlen 0x6
[ 6.960000] spiflash_ioctl_read, Read from 0x00fcf200 length 0x4, ret 0, retlen 0x4
[ 6.970000] spiflash_ioctl_read, Read from 0x00020000 length 0x200, ret 0, retlen 0x200
[ 6.980000] spiflash_ioctl_read, Read from 0x00fcf100 length 0x6, ret 0, retlen 0x6
[ 6.990000] ADDRCONF(NETDEV_UP): eth1: link is not ready
sendto /var/tmp/7 msg 2001 error No such file or directory ,pid 503
[ oal_sys_getOldTZInfo ] 650: Open TZ file error!
[ 7.770000] [ eth_vlan_write_proc ] 974: set VLAN Enable...
[ 7.770000] ioctl: No such device
spiflash_ioctl_read, Read from 0x00fcf100 length 0x6, ret 0, retlen 0x6
[ 8.920000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 8.930000] device eth0 entered promiscuous mode
[ 8.950000] device eth0.2 entered promiscuous mode
brctl: bridge br0: Device or resource busy
[ 8.980000] device eth0.3 entered promiscuous mode
brctl: bridge br0: Device or resource busy
[ 9.010000] device eth0.4 entered promiscuous mode
brctl: bridge br0: Device or resource busy
[ 9.040000] device eth0.5 entered promiscuous mode
brctl: bridge br0: Device or resource busy
[ 9.060000] br0: port 1(eth0) entered disabled state
[ 9.070000] [ eth_vlan_write_proc ] 974: set VLAN Enable...
[ 9.070000] ifconfig: ioctl 0x8913 failed: No such device
brctl: iface eth0.6: No such device
ifconfig: ioctl 0x8913 failed: No such device
brctl: iface eth0.6: No such device
*****The first two bytes of 2.4G caldata: 02 02*****
*****The first two bytes of 5.0G caldata: 20 2f*****
[ 9.230000] asf: module license 'Proprietary' taints kernel.
[ 9.230000] Disabling lock debugging due to kernel taint
[ 9.450000] ath_hal: 0.9.17.1 (AR9380, REGOPS_FUNC, WRITE_EEPROM, 11D)
[ 9.520000] ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
insmod: can't insert '/lib/modules/ath_dfs.ko': No such file or directory
[ 9.550000] ath_tx99: Version 2.0
[ 9.550000] Copyright (c) 2010 Atheros Communications, Inc, All Rights Reserved
[ 9.710000] ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
[ 11.580000] __ath_attach: Set global_scn[0]
[ 11.580000] *** All the minfree values should be <= ATH_TXBUF-32, otherwise default value will be used instead ***
[ 11.590000] ACBKMinfree = 48
[ 11.590000] ACBEMinfree = 32
[ 11.600000] ACVIMinfree = 16
[ 11.600000] ACVOMinfree = 0
[ 11.600000] CABMinfree = 48
[ 11.610000] UAPSDMinfree = 0
[ 11.610000] ATH_TXBUF=2700
[ 11.620000] Enterprise mode: 0x03bda000
[ 11.620000] Restoring Cal data from DRAM
[ 11.630000]
[ 11.630000] ART Version : -48.0.0
[ 11.630000] SW Image Version : -48.0.0.0.0
[ 11.640000] Board Revision :
[ 11.640000] ar9300_attach: nf_2_nom -110 nf_2_max -60 nf_2_min -125
[ 11.650000] ath_get_caps[6328] rx chainmask mismatch actual 7 sc_chainmak 0
[ 11.660000] ath_get_caps[6303] tx chainmask mismatch actual 7 sc_chainmak 0
[ 11.680000] ath_tx_paprd_init sc 87378000 PAPRD Enabled
[ 11.700000] wifi0: Atheros 956X: mem=0xb8100000, irq=47
[ 11.700000] ath_pci: (Atheros/multi-bss)
[ 11.710000] ol_ath_pci_probe: PCI device id 0056 :0056
[ 11.710000] ath_pci 0000:00:00.0: BAR 0: assigned [mem 0x12000000-0x121fffff 64bit]
[ 11.720000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 11.730000] *********** Besra *************
[ 11.730000]
[ 11.730000] __ol_ath_attach() Allocated scn 86140380
[ 11.740000] ath_pci 0000:00:00.0: ath DEBUG: sc=0x8719c400
[ 11.740000]
[ 11.740000] ol_ath_pci_configure : num_desired MSI set to 0
[ 11.750000]
[ 11.750000] Using PCI Legacy Interrupt
[ 11.760000] chip_id 0xc chip_revision 0x0
[ 11.770000]
[ 11.770000] CLOCK PLL skipped
[ 11.780000] HIF_PCIDeviceProbed: setting the target pll frac ffffffff intval ffffffff
[ 11.780000] HIF_PCIDeviceProbed: no frac provided, skipping pre-configuring PLL
[ 11.790000] __ol_ath_attach: dev name wifi1
[ 11.800000] ol_ath_attach interface_id 1
[ 11.800000] ol_ath_attach() BMI inited.
[ 11.810000] ol_ath_attach() BMI Get Target Info.
[ 11.820000] Chip id: 0xc, chip version: 0x1000000
[ 11.820000]
[ 11.820000] CE WAR Disabled
[ 11.830000] NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0
[ 11.830000] ol_ath_attach() configure Target .
[ 11.840000]
[ 11.840000] Target Version is 1000000
[ 11.840000]
[ 11.840000] Flash Download Address c0000
[ 11.850000] ol_transfer_bin_file: flash data file defined
[ 11.860000] Cal location [0]: 00004000
[ 11.860000]
[ 11.860000] wifi1 NAND FLASH Select OFFSET 0x5000
[ 11.870000] qc98xx_verify_checksum: flash checksum passed: 0xef05
[ 11.880000] ol_transfer_bin_file 3587: Download Flash data len 12064
[ 11.890000] Board extended Data download address: 0x0
[ 11.910000]
[ 11.910000] Board data initialized
[ 11.920000] ol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000
[ 11.930000]
[ 11.930000] Selecting OTP binary for CHIP Version 0 Type 12
[ 11.940000]
[ 11.940000] OTP filename QCA9888/hw.2/otp.bin
[ 11.940000]
[ 11.940000] ################# QCA9888/hw.2/otp.bin ##################
[ 11.950000] ol_transfer_bin_file 3407: downloading file 0, Download data len 8964
[ 11.990000]
[ 11.990000] First OTP send param 8000
[ 12.240000] ol_ath_download_firmware :First OTP download and Execute is good address:0x5000 return param 4660
[ 12.250000] ol_ath_download_firmware:##Board Id 20 , CHIP Id 0
[ 12.250000] ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000
[ 12.260000] Warning : No board id matched. Selecting default boarddata file
[ 12.270000]
[ 12.270000] wifi1: Selecting board data file name boarddata_0.bin
[ 12.280000] ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=QCA9888/hw.2/boarddata_0.bin
[ 12.290000]
[ 12.290000] ################# QCA9888/hw.2/boarddata_0.bin ##################
[ 12.300000] ol_transfer_bin_file 3407: downloading file 3, Download data len 12064
[ 12.310000] Board extended Data download address: 0x0
[ 12.330000] ol_ath_download_firmware: Using 0x1234 for the remainder of init
[ 12.340000]
[ 12.340000] Selecting OTP binary for CHIP Version 0 Type 12
[ 12.350000]
[ 12.350000] OTP filename QCA9888/hw.2/otp.bin
[ 12.350000]
[ 12.350000] ################# QCA9888/hw.2/otp.bin ##################
[ 12.360000] ol_transfer_bin_file 3407: downloading file 0, Download data len 8964
[ 12.400000]
[ 12.400000] [Flash] : Ignore Module param
[ 12.410000]
[ 12.410000] Second otp download Param 10000
[ 12.670000] ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0
[ 12.680000]
[ 12.680000] Mission mode: Firmware CHIP Version 0
[ 12.680000] ------------------> ol_swap_seg_alloc : filename = QCA9888/hw.2/athwlan.codeswap.bin !
[ 12.680000]
[ 12.700000] ol_swap_seg_alloc: Successfully allocated memory for SWAP size=262144
[ 12.700000] ------------------> ol_swap_wlan_memory_expansion : filename = QCA9888/hw.2/athwlan.codeswap.bin !
[ 12.700000]
[ 12.720000] Swap: bytes_left to copy: fw:16; dma_page:61955
[ 12.720000] Swap: wrong length read:0
[ 12.730000] ol_swap_wlan_memory_expansion: Swap total_bytes copied: 200189 Target address 419530
[ 12.740000] scn=86140380 target_write_addr=419530 seg_info=87190510
[ 12.740000] ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2
[ 12.750000] bin_filename=QCA9888/hw.2/athwlan.bin swap_filename=/lib/firmware/QCA9888/hw.2/athwlan.codeswap.bin
[ 12.760000] ol_transfer_bin_file: Downloading firmware file: QCA9888/hw.2/athwlan.bin
[ 12.770000]
[ 12.770000] ################# QCA9888/hw.2/athwlan.bin ##################
[ 12.780000] ol_transfer_bin_file 3407: downloading file 1, Download data len 351944
[ 14.150000] ol_ath_attach() Download FW done.
[ 14.150000] ol_ath_attach() HT Create .
[ 14.160000] ol_ath_attach() HIF Claim.
[ 14.160000] ol_ath_attach() BMI Done.
[ 14.170000] ol_ath_attach 7584 host_enable 0 nss_nwifi_offload 0
[ 14.170000] ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko)
[ 14.180000] OL_ACBKMinfree : 0
[ 14.180000] OL_ACBEMinfree : 0
[ 14.190000] OL_ACVIMinfree : 0
[ 14.190000] OL_ACVOMinfree : 0
[ 14.190000] ol_ath_attach() WMI attached. wmi_handle 86020000
[ 14.200000] CE_recv_buf_enqueue 877 Populate last entry 512 for CE 5
[ 14.210000] CE_recv_buf_enqueue 886 CE 5 wi 511 dest_ptr 0x5b37020 nbytes 0 recv_ctxt 0x85a85240
[ 14.220000] Startup Mode-0 set
[ 14.220000]
[ 14.220000] <=== cfg max peer id 1056 ====>
[ 14.230000] HTC Service:0x0300 ep:1 TX flow control disabled
[ 14.240000] htt_peer_map_timer_init Enter pdev 85bc0000 hrtimer 85bc47c0
[ 14.240000]
[ 14.240000] htt_alloc_peer_map_mem : Alloc Success : host q vaddr 85448000 paddr 5448000
[ 14.250000]
[ 14.250000] htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts
[ 14.270000] CE_pkt_dl_len_set CE 4 Pkt download length 64
[ 14.270000] ol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from 85080000
[ 14.280000] HTC Service:0x0100 ep:2 TX flow control disabled
[ 14.290000] wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event
[ 14.300000] Firmware_Build_Number:99
[ 14.300000] host/RAM_fw Build Ver Mismatch: H:0x5D, F:0x63 !
[ 14.310000] num_rf_chain:0x00000002 ht_cap_info:0x0000085b vht_cap_info:0x339979f2 vht_supp_mcs:0x0000fffa
[ 14.320000]
[ 14.320000] RES CFG Support wmi_service_bitmap 9778
[ 14.320000]
[ 14.320000] Sending Ext resource cfg: HOST PLATFORM as 1 and fw_feature_bitmap as 50 to TGT
[ 14.330000] ol_ath_service_ready_event: tt_support: 1
[ 14.340000] ol_ath_service_ready_event: periodic_chan_stats: 0
[ 14.340000] Peer Caching Enabled ; num_peers = 530, num_active_peers = 52 num_tids = 104, num_vdevs = 17
[ 14.350000] idx 1 req 2 num_units 1 num_unit_info 12 unit size 256 actual units 53
[ 14.360000] ol_ath_alloc_host_mem_chunk req_id 2 idx 0 num_units 53 unit_len 256,
[ 14.370000] idx 2 req 3 num_units 1 num_unit_info 12 unit size 1024 actual units 53
[ 14.380000] ol_ath_alloc_host_mem_chunk req_id 3 idx 1 num_units 53 unit_len 1024,
[ 14.390000] idx 3 req 4 num_units 1 num_unit_info 12 unit size 4096 actual units 53
[ 14.400000] ol_ath_alloc_host_mem_chunk req_id 4 idx 2 num_units 53 unit_len 4096,
[ 14.400000] idx 0 req 1 num_units 0 num_unit_info 2 unit size 872 actual units 531
[ 14.410000] ol_ath_alloc_host_mem_chunk req_id 1 idx 3 num_units 265 unit_len 872,
[ 14.420000] ol_ath_alloc_host_mem_chunk req_id 1 idx 4 num_units 266 unit_len 872,
[ 14.430000] idx 4 req 5 num_units 0 num_unit_info 2 unit size 1892 actual units 531
[ 14.440000] ol_ath_alloc_host_mem_chunk req_id 5 idx 5 num_units 132 unit_len 1892,
[ 14.450000] ol_ath_alloc_host_mem_chunk req_id 5 idx 6 num_units 133 unit_len 1892,
[ 14.460000] ol_ath_alloc_host_mem_chunk req_id 5 idx 7 num_units 133 unit_len 1892,
[ 14.470000] ol_ath_alloc_host_mem_chunk req_id 5 idx 8 num_units 133 unit_len 1892,
[ 14.470000] chunk 0 len 13568 requested ,ptr 0x5054000
[ 14.480000] chunk 1 len 54272 requested ,ptr 0x50a0000
[ 14.480000] chunk 2 len 217088 requested ,ptr 0x50c0000
[ 14.490000] chunk 3 len 231080 requested ,ptr 0x5100000
[ 14.500000] chunk 4 len 231952 requested ,ptr 0x5140000
[ 14.500000] chunk 5 len 249744 requested ,ptr 0x5180000
[ 14.510000] chunk 6 len 251636 requested ,ptr 0x51c0000
[ 14.510000] chunk 7 len 251636 requested ,ptr 0x5200000
[ 14.520000] chunk 8 len 251636 requested ,ptr 0x5240000
[ 14.550000] wmi_ready_event_rx: WMI UNIFIED READY event
[ 14.550000] ol_ath_connect_htc() WMI is ready
[ 14.560000] target uses HTT version 2.2; host uses 2.2
[ 14.570000] ol_ath_attach() connect HTC.
[ 14.570000] bypasswmi : 0
[ 14.570000] ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0.
[ 14.590000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2) flags 0x2150
[ 14.590000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4) flags 0xa0
[ 14.600000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x8) flags 0xc0
[ 14.610000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x20) flags 0xd0
[ 14.620000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x40) flags 0x150
[ 14.620000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x800) flags 0x10080
[ 14.630000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2000) flags 0x20080
[ 14.640000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4000) flags 0x40080
[ 14.650000] Add VHT80 channel: 5210
[ 14.650000] Add VHT80 channel: 5290
[ 14.650000] Add VHT80 channel: 5530
[ 14.660000] Add VHT80 channel: 5610
[ 14.660000] Add VHT80 channel: 5690
[ 14.660000] Add VHT80 channel: 5775
[ 14.670000] Skipping VHT80 channel 5825
[ 14.670000] OL Resmgr Init-ed
[ 14.680000] rate power table override is only supported for AR98XX
[ 14.690000] ol_ath_attach() UMAC attach .
[ 14.690000]
[ 14.690000] BURSTING enabled by default
[ 14.700000] __ol_ath_attach: needed_headroom reservation 44
[ 14.700000] ol_ath_thermal_mitigation_attach: --
Invalid command : enable_ol_stats
[ 14.940000] wlan_vap_create : enter. devhandle=0x872d0380, opmode=IEEE80211_M_HOSTAP, flags=0x1
[ 14.940000]
[ 14.950000] ieee80211_mbo_vattach:MBO Initialized
[ 14.960000] wlan_vap_create : exit. devhandle=0x872d0380, opmode=IEEE80211_M_HOSTAP, flags=0x1.
[ 14.960000]
[ 14.970000] VAP device ath0 created osifp: (850b5380) os_if: (85fa8000)
ath0
[ 15.170000] [wifi1] FWLOG: [20935] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x94c, 0x94c, 0x0 )
[ 15.180000] [wifi1] FWLOG: [20935] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x94c, 0x94c, 0x0 )
[ 15.180000] [wifi1] FWLOG: [20935] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x94c, 0x94c, 0x0 )
[ 15.190000] [wifi1] FWLOG: [20935] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x94c, 0x94c, 0x0 )
[ 15.200000] [wifi1] FWLOG: [20935] WAL_DBGID_TX_AC_BUFFER_SET ( 0x100, 0x11e1a300 )
[ 15.990000] wlan_vap_create : enter. devhandle=0x872d0380, opmode=IEEE80211_M_STA, flags=0x3
[ 15.990000]
[ 16.000000] wlan_vap_create : exit. devhandle=0x872d0380, opmode=IEEE80211_M_STA, flags=0x3.
[ 16.000000]
[ 16.010000] VAP device ath1 created osifp: (850b7380) os_if: (850bc000)
ath1
[ 17.040000] ieee80211_extap_detect_stop: stop.
[ 17.050000] wlan_vap_create : enter. devhandle=0x872d0380, opmode=IEEE80211_M_HOSTAP, flags=0x1
[ 17.050000]
[ 17.060000] ieee80211_mbo_vattach:MBO Initialized
[ 17.060000] wlan_vap_create : exit. devhandle=0x872d0380, opmode=IEEE80211_M_HOSTAP, flags=0x1.
[ 17.060000]
[ 17.070000] VAP device ath2 created osifp: (85f91380) os_if: (85f8c000)
ath2
[ 17.150000]
[ 17.150000] DES SSID SET=TP-Link_149D
[ 17.230000] siwfreq
[ 17.230000] Set freq vap 0 stop send + 85fa8000
[ 17.240000] Set freq vap 0 stop send -85fa8000
[ 17.270000] Set wait done --85fa8000
[ 17.270000] Set freq vap 0 stop send + 85f8c000
[ 17.270000] Set freq vap 0 stop send -85f8c000
[ 17.310000] Set wait done --85f8c000
[ 17.380000] WARNING: Fragmentation with HT mode NOT ALLOWED!!
Error for wireless request "Set Fragmentation Threshold" (8B24) :
SET failed on device ath0 ; Invalid argument.
Sorry, rule does not exist.
[ 17.440000] Setting Max Stations:32
[ 17.490000]
[ 17.490000] DES SSID SET=TP-Link_Guest_149D
[ 17.540000] Switching to Tx Mode-0
[ 17.560000] WARNING: Fragmentation with HT mode NOT ALLOWED!!
Error for wireless request "Set Fragmentation Threshold" (8B24) :
SET failed on device ath2 ; Invalid argument.
[ 17.600000] Setting Max Stations:32
Reading topology file /var/Wireless/2_4G_topology.conf ...
417.455: Reading radio configuration file /var/Wireless/2_4G_80211g.ap_radio ...
417.455: Reading bss configuration file /var/Wireless/ath0.ap_bss ...
[ 17.920000] ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1
Using interface ath0 with hwaddr 70:4f:57:42:14:9d and ssid 'TP-Link_149D'
[ 18.040000]
[ 18.040000] DES SSID SET=TP-Link_149D
[ 18.050000] Warning: node not in table 0x85072000
417.642: upnp_wps_device_init called
l2_packet_receive - recvfrom: Network is down
Invalid command : vap_ind
[ 18.720000] registe callback function for ath0
atheros_wireless[ 18.750000] 8021q: adding VLAN 0 to HW filter on device ath0
_event_receive:Malformed netlink message: len=1000 left=512 plen=984
512 extra bytes in the end of netlink message
[ 18.780000] registe callback function for ath0
[ 21.520000] ieee80211_extap_detect_stop: stop.
[ 21.590000] device ath0 entered promiscuous mode
[ 21.590000] br0: port 1(ath0) entered forwarding state
[ 21.600000] br0: port 1(ath0) entered forwarding state
atheros_wireless_event_receive:Malformed netlink message: len=996 left=512 plen=[ 21.610000] device ath1 entered promiscuous mode
980
512 extra bytes in the end of netlink message
[ 21.620000] device ath2 entered promiscuous mode
*****The first two bytes of 2.4G caldata: 02 02*****
*****The first two bytes of 5.0G caldata: 20 2f*****
atheros_wireless_event_receive:Malformed netlink message: len=1004 left=512 plen=988
512 extra bytes in the end of netlink message
[ 21.690000] wmi_unified_vdev_create_send: ID = 0 Type = 1, Subtype = 0 VAP Addr = 70:4f:57:42:14:9f:
[ 21.700000] ieee80211_mbo_vattach:MBO Initialized
[ 21.700000] VAP device ath5 created osifp: (85f93b80) os_if: (852cc000)
atheros_wireless_event_receive:Malformed netlink message: len=1000 left=512 plen=984
512 extra bytes in the end of netlink message
ath5
[ 22.170000] [wifi1] FWLOG: [28224] WAL_DBGID_DEV_RESET ( 0xc01d, 0x42b )
[ 22.720000] wmi_unified_vdev_create_send: ID = 1 Type = 2, Subtype = 0 VAP Addr = 76:4f:57:42:14:9f:
[ 22.730000] wmi_unified_set_psmode:set psmode=1
[ 22.730000] VAP device ath6 created osifp: (852e5b80) os_if: (852e0000)
ath6
atheros_wireless_event_receive:Malformed netlink message: len=1000 left=512 plen=984
512 extra bytes in the end of netlink message
[ 23.750000] wmi_unified_set_psmode:set psmode=0
[ 23.760000] wmi_unified_set_psmode:set psmode=0
[ 23.770000] ieee80211_extap_detect_stop: stop.
[ 23.770000] wmi_unified_set_psmode:set psmode=0
[ 23.780000] wmi_unified_set_psmode:set psmode=0
[ 23.790000] wmi_unified_vdev_create_send: ID = 2 Type = 1, Subtype = 0 VAP Addr = 7a:4f:57:42:14:9f:
[ 23.800000] ieee80211_mbo_vattach:MBO Initialized
[ 23.810000] VAP device ath7 created osifp: (852f8380) os_if: (852fc000)
ath7
atheros_wireless_event_receive:Malformed netlink message: len=1000 left=512 plen=984
512 extra bytes in the end of netlink message
[ 23.830000]
[ 23.830000] DES SSID SET=TP-Link_149D_5G
atheros_wireless_event_receive:Malformed netlink message: len=1004 left=512 plen[ 23.850000] [ol_ath_iw_setcountry][1680] *p=44, *(p+1)=45
=988
512 extra [ 23.860000] isCountryCodeValid: EEPROM regdomain 0x0
bytes in the end[ 23.870000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2) flags 0x2150
of netlink mess[ 23.880000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4) flags 0xa0
age
[ 23.880000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x8) flags 0xc0
[ 23.890000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x20) flags 0xd0
[ 23.900000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x40) flags 0x150
[ 23.910000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x800) flags 0x10080
[ 23.910000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x2000) flags 0x20080
[ 23.920000] ol_regdmn_init_channels: !avail mode 0x7f9001 (0x4000) flags 0x40080
[ 23.930000] Add VHT80 channel: 5210
[ 23.930000] Add VHT80 channel: 5290
[ 23.940000] Add VHT80 channel: 5530
[ 23.940000] Add VHT80 channel: 5610
[ 23.940000] Skipping VHT80 channel 5660
[ 23.950000] Skipping VHT80 channel 5680
[ 23.950000] Skipping VHT80 channel 5700
atheros_wireless_event_receive:Malformed netlink message: len=1004 left=512 plen=988
512 extra bytes in the end of netlink message
List Flushed
Following channels are blocked from Channel selection algorithm
[52] [56] [60[ 24.020000] siwfreq
] [64] [100] [10[ 24.030000] Set freq vap 0 stop send + 852cc000
4] [108] [112] [[ 24.030000] Set freq vap 0 stop send -852cc000
116] [120] [124] [128] [132] [136] [140] [149] [153] [157] [161] [165]
[ 24.070000] Set wait done --852cc000
[ 24.070000] Set freq vap 0 stop send + 852fc000
[ 24.070000] Set freq vap 0 stop send -852fc000
[ 24.110000] Set wait done --852fc000
[ 24.140000] ME Pool succesfully initialized vaddr - 85320000 paddr - 0
[ 24.140000] num_elems = 1424 buf_size - 64 pool_size = 102528
[ 24.160000] Enable MCAST_TO_UCAST
[ 24.170000] su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1
[ 24.180000] su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1
[ 24.190000] su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1
[ 24.210000] su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1
[ 24.240000] WARNING: Fragmentation with HT mode NOT ALLOWED!!
Error for wireless request "Set Fragmentation Threshold" (8B24) :
SET failed on device ath5 ; Invalid argument.
Sorry, rule does not exist.
[ 24.280000] Setting Max Stations:32
[ 24.340000]
[ 24.340000] DES SSID SET=TP-Link_Guest_149D_5G
[ 24.400000] WARNING: Fragmentation with HT mode NOT ALLOWED!!
Error for wireless request "Set Fragmentation Threshold" (8B24) :
SET failed on device ath7 ; Invalid argument.
[ 24.440000] Setting Max Stations:32
Reading topology file /var/Wirel[ 24.520000] ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1
ess/5G_topology.conf ...
424.110: Reading radio configuration file /var/Wireless/5G_80211g.ap_radio ...
424.110: Reading bss configuration file /var/Wireless/ath5.ap_bss ...
Using interface ath5 with hwaddr 70:4f:57:42:14:9f and ssid 'TP-Link_149D_5G'
[ 24.650000]
[ 24.650000] DES SSID SET=TP-Link_149D_5G
424.245: upnp_wps_device_init called
l2_packet_receive - recvfrom: Network is down
[ 25.170000] [wifi1] FWLOG: [31289] WAL_DBGID_SECURITY_ENCR_EN ( )
[ 25.180000] [wifi1] FWLOG: [31289] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 )
Invalid command : vap_ind
[ 25.560000] registe callback function for ath5
atheros_wireless[ 25.590000] 8021q: adding VLAN 0 to HW filter on device ath5
_event_receive:Malformed netlink message: len=1000 left=512 plen=984
512 extra bytes in the end of netlink message
atheros_wir[ 25.600000] device ath5 entered promiscuous mode
eless_event_rece[ 25.610000] br0: port 8(ath5) entered forwarding state
ive:Malformed ne[ 25.620000] br0: port 8(ath5) entered forwarding state
tlink message: len=1000 left=512 plen=984
512 extra bytes in the end of netlink[ 25.630000] device ath6 entered promiscuous mode
message
[ 25.640000] device ath7 entered promiscuous mode
[src/cloud_downloadHandler.c:cloud_initPthreadDownloadHandler:241] init download handler success!
[src/cloud_downloadHandler.c:downloadHandler:104] Enter download handler, download firmware from cloud...
[src/cloud_downloadHandler.c:downloadHandler:108] wait semaphore to download firmware to device...
mmmInit():Total mem size=51364, addr=0x0x69c008.
*************************************************************
*************************MMM TABLE DUMP**********************
-------------------------------------------------------------
sendto /var/tmp/8 msg 2030 error No such file or directory ,pid 503
poolhead(40) poolnum dynamictimes chainhead poolend
-------------------------------------------------------------
0x69c008 8 0 (nil) 0x6a88ac
-------------------------------------------------------------
index poolhead(20) size blocks free usage
-------------------------------------------------------------
1 0x69c030 32 256 256 0
2 0x69e448 64 128 128 0
3 0x6a0660 128 64 64 0
4 0x6a2778 256 32 32 0
5 0x6a4810 512 8 8 0
6 0x6a5848 1024 4 4 0
7 0x6a6870 2048 2 2 0
8 0x6a7890 4096 1 1 0
-------------------------------------------------------------
index chainnode(16) magic length prev next
-------------------------------------------------------------
(nil)
*************************************************************
[ 26.170000] [wifi1] FWLOG: [32242] WAL channel change freq=5180, mode=0 flags=0 rx_ok=1 tx_ok=1
[ 26.180000] [wifi1] FWLOG: [32556] WAL channel change freq=5200, mode=0 flags=0 rx_ok=1 tx_ok=1
sendto /var/tmp/9 msg 2004 error No such file or directory ,pid 503
sendto /var/tmp/9 msg 2004 error No such file or directory ,pid 503
sendto /var/tmp/9 msg 2004 error No such file or directory ,pid 503
[ ipsecEntry ] 357: ipsec mkdir error
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
radvd starting
[ modifyL2BridgingFromLantoWan ] 155: Fail to get LANDevice object (eth1), ret = 9806
[ rsl_initEwanObj ] 307: Initialize EWAN failed!
[ 26.940000] [ag71xx_rings_cleanup:348]ag71xx_rings_cleanup
atheros_wireless_event_receive:Malformed netlink message: len=1004 left=512 plen=988
512 extra [ 26.950000] ADDRCONF(NETDEV_UP): eth1: link is not ready
bytes in the end of netlink message
atheros_wireless_event_receive:Malformed netlink message: len=1004 left=512 plen=988
512 extra bytes in the end of netlink message
atheros_wireless_event_receive:Malformed netlink message: len=1004 left=512 plen=988
512 extra bytes in the end of netlink message
atheros_wireless_event_receive:Malformed netlink message: len=1004 left=512 plen=988
512 extra bytes in the end of netlink message
atheros_wireless_event_receive:Malformed netlink message: len=1004 left=512 plen=988
512 extra bytes in the end of netlink message
atheros_wireless_event_receive:Malformed netlink message: len=1004 left=512 plen=988
512 extra bytes in the end of netlink message
[ rsl_initWanIpConnObj ] 752: This connType(dhcp_USB_4G) is not up in current mode!
[ rsl_initWanPppConnObj ] 286: This connType(ppp_USB_3G) is not up in current mode!
[ 27.170000] [wifi1] FWLOG: [32871] WAL channel change freq=5220, mode=0 flags=0 rx_ok=1 tx_ok=1
[ 27.180000] [wifi1] FWLOG: [33185] WAL channel change freq=5240, mode=0 flags=0 rx_ok=1 tx_ok=1
[ 27.190000] [wifi1] FWLOG: [33499] WAL channel change freq=5260, mode=0 flags=0 rx_ok=1 tx_ok=1
[ 27.200000] [wifi1] FWLOG: [33812] WAL channel change freq=5280, mode=0 flags=0 rx_ok=1 tx_ok=1
[ getPidFromPidFile ] 112: Cann't open file: /var/run/zebra.pid.
[ getPidFromPidFile ] 112: Cann't open file: /var/run/ripd.pid.
iptables: Bad rule (does a matching rule exist in that chain?).
insmod: can't insert '/lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_proto_gre.ko': File exists
insmod: can't insert '/lib/modules/kmdir/kernel/net/netfilter/nf_conntrack_pptp.ko': File exists
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
ip6tables v1.4.17: Couldn't find target `FWRULE'
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables v1.4.17: Couldn't find target `INPUT_FWRULE'
Try `ip6tables -h' or 'ip6tables --help' for more information.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
ip6tables: No chain/target/match by that name.
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
ip6tables: Bad rule (does a matching rule exist in that chain?).
[src/cloud_client.c:initSigIntHandler:104] init signal handler success!
[src/cloud_client.c:cloudClientInit:148] Init cloud-client environment successful.
[src/cloud_localMsgHandler.c:cloud_localMsgTask:96] Start cloud local message observer...
ip6tables: Bad rule (does a matching rule exist in that chain?).
ip6tables: Bad rule (does a matching rule exist in that chain?).
Sorry, rule does not exist.
iptables: Bad rule (does a matching rule exist in that chain?).
[ 28.170000] [wifi1] FWLOG: [34127] WAL channel change freq=5300, mode=0 flags=0 rx_ok=1 tx_ok=1
[ 28.180000] [wifi1] FWLOG: [34441] WAL channel change freq=5320, mode=0 flags=0 rx_ok=1 tx_ok=1
[ 28.190000] [wifi1] FWLOG: [34754] WAL channel change freq=5500, mode=0 flags=0 rx_ok=1 tx_ok=1
ip6tables: Bad rule (does a matching rule exist in that chain?).
ip6tables: Bad rule (does a matching rule exist in that chain?).
[ rsl_setStorageServiceObj ] 1394: mountFlag is 3,We start usb server
killall: minidlnad: no process killed
[ 29.170000] [wifi1] FWLOG: [35068] WAL channel change freq=5520, mode=0 flags=0 rx_ok=1 tx_ok=1
[ 29.180000] [wifi1] FWLOG: [35383] WAL channel change freq=5540, mode=0 flags=0 rx_ok=1 tx_ok=1
[ 29.190000] [wifi1] FWLOG: [35697] WAL channel change freq=5560, mode=0 flags=0 rx_ok=1 tx_ok=1
[ 30.170000] [wifi1] FWLOG: [36011] WAL channel change freq=5580, mode=0 flags=0 rx_ok=1 tx_ok=1
[ 30.180000] [wifi1] FWLOG: [36325] WAL channel change freq=5600, mode=0 flags=0 rx_ok=1 tx_ok=1
[ 30.190000] [wifi1] FWLOG: [36638] WAL channel change freq=5620, mode=0 flags=0 rx_ok=1 tx_ok=1
iptables: Bad rule (does a matching rule exist in that chain?).
iptables: Bad rule (does a matching rule exist in that chain?).
ip6tables: Bad rule (does a matching rule exist in that chain?).
[ 30.820000] kcg 333 :GPL NetUSB up!
[ 30.920000] kc 227 : init_DebugD end
[ 30.920000] INFO18D9: NetUSB 1.02.95, 00030308 : Mar 27 2017 11:28:05
[ 30.930000] INFO18DB: 7437: TL-MR3620 :TL-MR3620
[ 30.940000] INFO18DC: AUTH ISOC
[ 30.940000] INFO18DD: filterAudio
[ 30.940000] kc 90 : run_telnetDBGDServer start
[ 30.950000] usbcore: registered new interface driver KC NetUSB General Driver
[ 30.960000] INFO01F9: init proc : PAGE_SIZE 4096
[ 30.970000] INFO17E8: infomap 84e0d47c
[ 30.970000] INFO17EC: bndev : br0
[ 30.980000] INFO17F1: sleep to wait br0 to wake up
[ 30.980000] INFO1610: tcpConnector() started... : br0
[ 31.170000] [wifi1] FWLOG: [36953] WAL channel change freq=5640, mode=0 flags=0 rx_ok=1 tx_ok=1
[ 31.180000] [wifi1] FWLOG: [37267] WAL channel change freq=5660, mode=0 flags=0 rx_ok=1 tx_ok=1
[ 31.190000] [wifi1] FWLOG: [37581] WAL channel change freq=5680, mode=0 flags=0 rx_ok=1 tx_ok=1
[ 31.200000] [wifi1] FWLOG: [37895] WAL channel change freq=5700, mode=0 flags=0 rx_ok=1 tx_ok=1
[ 31.410000] wmi_unified_vdev_down_send for vap 0 (86020000)
[ 31.420000] ieee80211_extap_detect_stop: stop.
[ 31.430000] OL vap_start +
[ 31.430000] wmi_unified_vdev_start_send for vap 0 (86020000)
[ 31.430000] OL vap_start -
[ 31.440000] ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3
[ 31.620000] ol_vdev_start_resp_ev for vap 0 (86020000)
[ 31.630000] su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1
[ 31.640000] wmi_unified_vdev_up_send for vap 0 (86020000)
[ 32.170000] [wifi1] FWLOG: [38214] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )
[ 32.180000] [wifi1] FWLOG: [38214] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )
[ 32.180000] [wifi1] FWLOG: [38228] vap-0 VDEV_MGR_VDEV_START ( 0x143c, 0x2, 0x0, 0x0 )
[ 32.190000] [wifi1] FWLOG: [38228] WAL channel change freq=5180, mode=10 flags=0 rx_ok=1 tx_ok=1
[ 32.200000] [wifi1] FWLOG: [38442] VDEV_MGR_HP_START_TIME ( 0x0, 0x143c, 0x1068000 )
[ 32.210000] [wifi1] FWLOG: [38442] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x1 )
[ 32.220000] [wifi1] FWLOG: [38442] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )
[ 32.220000] [wifi1] FWLOG: [38442] VDEV_MGR_AP_TBTT_CONFIG ( 0x0, 0x143c, 0x0, 0x0 )
[ 34.050000] INFO15C0: Bind to br0
Will output 1024 bit rsa secret key to '/var/tmp/dropbear/dropbear_rsa_host_key'
Generating key, this may take a while...
Public key portion is:
ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAAAgnW/hwg0CvEL5aj5fDAeylCiYYmxHRY6YdEdAxNvjOWcej6jHvPPh5Ad3bly5FlWIxGTEH2+qn8E7MMxx+KuSdKSKGaSOu7H6/CXz/G2IEmLc7wh0YeZrb8fgmsvWxWCsqHEsrbPX+S2UDSsr/AIKhOESpPAJelgyM/wca6sTyF7UBE= admin@TL-MR3620
Fingerprint: md5 94:cf:9c:36:ef:ac:e0:34:fb:9e:06:62:18:26:90:98
Will output 1024 bit dss secret key to '/var/tmp/dropbear/dropbear_dss_host_key'
Generating key, this may take a while...
[ 38.950000] sched: RT throttling activated
Public key portion is:
ssh-dss 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 admin@TL-MR3620
Fingerprint: md5 ae:84:71:19:07:56:b1:8f:18:43:03:93:a7:15:e5:28
451.183: ath0: STA 70:4f:57:42:14:9d IEEE 802.11: disassociated
|
=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
Last edited by zarkmughal on Mon Apr 10, 2023 4:13; edited 1 time in total |
|